Heat & Glo LifeStyle MTL-INSERT Electrical Information, Wiring the Appliance, ON/OFF Switch

Page 16

9 Electrical Information

A. Wiring the Appliance

Appliance Requirements

Note: Electrical wiring must be installed by a licensed electrician.

Note: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electric Code, CSA C221.1.

CAUTION

•Prevent accidental appliance operation when not attended.

•Unplug or remove batteries from remote control if absent or if appliance will not be used for an extended period of time.

•Property damage possible from elevated temperatures.

•This appliance DOES NOT require 110-120 VAC to operate.

•It is recommended that a 110 VAC junction box be connected for use with fan or remote control. (See Figure 9.2 for junction box wiring).

WARNING

Wire 110V to electrical junction box.

Do NOT wire 110V to valve.

Do NOT wire 110V to wall switch.

•Incorrect wiring will damage millivolt valves.

•Incorrect wiring will override IPI safety lockout and may cause explosion.

ON/OFF Switch

• An ON/OFF switch is included with the door/front and should be attached to the door/front. The location of the ON/OFF switch varies depending on model. It may be installed on the valve cover plate or included with the decorative surround. (See Installation instructions for remote control).

• If desired an additional wall switch or thermostat may be added to system as shown in Figure 9.1. Follow directions included with the optional wall switch.

STANDING

 

PILOT

 

 

 

REMOTE SWITCH

 

 

PIGTAIL

 

 

ON

 

 

OFF

 

VALVE

ON/OFF

 

SWITCH

 

 

 

WHT

 

 

RED

OPTIONAL WALL SWITCH,

 

 

THERMOSTAT OR REMOTE

Î Figure 9.1

Standing Pilot Ignition Wiring Diagram

 

16

Heat & Glo • MTL-Insert • 2145-900 Rev. D • 3/08

Page 15 Page 17
Image 16
Page 15 Page 17
Contents What to do if you smell gas Model MTL-InsertHOT Surfaces Homeowner Reference Information XxxxxxxxTable of Contents Listing and Code Approvals Design and Installation Considerations Getting StartedTools and Supplies Needed Inspect Appliance and ComponentsFireplace Size Requirements Minimum Fireplace OpeningClearances Clearances to Mantels or other Combustibles above ApplianceTermination Locations Vent Termination Minimum ClearancesVent Information and Diagrams Vent Table KeyHorizontal Venting Measuring StandardsInstallation Preparation Connecting Vent Pipe Installing Vent Pipe and ApplianceVenting Components Placing, Securing and Leveling the Appliance Installing Termination Cap Factory Built Wood BurningDamper Flashing Kit Optional Class a PipeFuel Conversions Gas Connection Gas InformationGas Pressures High Altitude Installations Check for GAS LeaksWiring the Appliance ON/OFF SwitchElectrical Information Appliance RequirementsOptional Junction Box Installation Optional AccessoriesVariable Speed Control Junction BOX BLK Finishing Mantel ProjectionsAppliance Setup Clean the ApplianceAccessories Ember PlacementLog Set Assembly LOGS-SXT Positioning the LogsHeat & Glo MTL-Insert 2145-900 Rev. D 3/08 Heat & Glo MTL-Insert 2145-900 Rev. D 3/08 Glass Assembly Air Shutter SettingRemoving Glass Assembly Replacing Glass AssemblyBefore Lighting Appliance Operating InstructionsBefore operating this appliance have a qualified technician Standing Pilot Ignition Lighting ApplianceWhat to do if YOU Smell GAS Check Pilot Flame Appearance Initial Break-in ProcedureAfter Appliance is Lit Frequently Asked Questions Issue SolutionsSymptom Possible Causes Corrective Action TroubleshootingStanding Pilot Ignition System Troubleshooting Symptom Possible Cause Corrective ActionMaintenance Tasks Maintaining and Servicing ApplianceInspect Maintenance Tasks Doors, SurroundsAppliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsService Parts Log Set AssemblyPart number list on following Stocked Service PartsAt Depot Standing Pilot Valve Assembly Limited Lifetime Warranty Limited Lifetime Warranty Heat & GLO GAS Appliance ProductsContact Information

MTL-INSERT specifications

The Heat & Glo LifeStyle MTL-INSERT is a remarkable gas fireplace insert that combines elegance, innovation, and cutting-edge technology to enhance the comfort and atmosphere of your home. Designed to seamlessly fit into existing masonry or factory-built fireplaces, the MTL-INSERT transforms any living space with minimal installation effort, making it a practical choice for both renovations and new builds.

One of the standout features of the LifeStyle MTL-INSERT is its contemporary style, which includes clean lines and a sleek facade. This insert is available in various sizes and configurations, allowing homeowners to select the ideal fit for their specific fireplace and aesthetic needs. The large viewing area provided by the expansive glass front ensures that the mesmerizing dance of the flames can be enjoyed from multiple angles in any room.

The MTL-INSERT is equipped with a powerful heat output, efficiently warming spaces without the need for additional heating sources. It utilizes advanced heat distribution technologies, including a blower system that circulates warm air throughout the room, making it not only a beautiful addition but also a functional one. With an impressive BTU range, it excels in heating capacities, ensuring comfort even in colder climates.

One of the key innovations of the LifeStyle MTL-INSERT is its use of the IntelliFire® technology. This patented system allows for easy control of the fireplace with a remote control, wall switch, or smart home integration, providing convenience and accessibility. The IntelliFire® technology also features an automatic ignition system, allowing for fast and reliable lighting of the flames without the hassle of manual starters.

Additionally, the LifeStyle MTL-INSERT is designed with safety and efficiency in mind. The unit is equipped with an oxygen depletion sensor (ODS) that automatically turns off the gas supply if the oxygen levels in the room become too low. This ensures peace of mind while enjoying the warmth and ambiance of the fireplace.

With environmentally friendly options, including a variety of fuel types such as natural gas or propane, the MTL-INSERT can cater to different homeowner preferences while maintaining optimal efficiency. The incorporation of high-quality materials and craftsmanship guarantees durability and longevity, ensuring that this investment will serve as a centerpiece in your home for years to come.

In conclusion, the Heat & Glo LifeStyle MTL-INSERT stands out as an exceptional choice for those seeking a modern and efficient gas fireplace insert. Its blend of advanced technologies, stylish design, and powerful heating capabilities make it a sought-after addition to any home, providing both comfort and an inviting atmosphere that families can enjoy together.
Top Page Image Contents