Heat & Glo LifeStyle MTL-INSERT Maintaining and Servicing Appliance, Maintenance Tasks

Page 31

14 Maintaining and Servicing Appliance

A. Maintenance Tasks

Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualified service technician should perform an appliance checkup at the beginning of each heating season.

WARNING

Risk of injury or property damage.

Before servicing:

•Turn off gas.

•Turn off electricity to appliance.

•Disable remote control, if one is present.

•Ensure appliance is completely cooled.

After servicing:

•Replace any screen or barrier that was removed.

•Reseal and reinstall any venting removed for servicing.

WARNING

Annual inspection by qualified technician recommended.

Check:

•Condition of doors, surrounds and fronts.

•Condition of glass, glass assembly and glass seal.

•Obstructions of combustion and ventilation air.

•Condition of logs.

•Condition of firebox.

•Burner ignition and operation.

•Burner air shutter adjustment

•Gas connections and fittings.

•Obstructions of termination cap.

Clean:

• Glass

•Air passageways, grilles, control compartment

•Burner, burner ports

Risk of:

•Fire

•Delayed ignition or explosion

•Exposure to combustion fumes

•Odors

CAUTION

Handle glass assembly with care.

NOTE: Clean glass after initial 3-4 hours operation.

Longer operation without cleaning glass may cause a permanent white film on glass.

When cleaning glass door:

•Avoid striking, scratching or slamming glass.

•Do NOT use abrasive cleaners.

•Use a hard water deposit glass cleaner on white film.

•Do NOT clean glass when hot.

•Turn off appliance after 3-4 hours of operation and

ALLOW TO COOL.

•Remove and clean glass assembly.

•Replace glass assembly and operate appliance for additional 12 hours.

Refer to maintenance instructions.

WARNING

Inspect external vent cap regularly.

•Ensure no debris blocks cap.

•Combustible materials blocking cap may ignite.

•Restricted air flow affects burner operation.

Heat & Glo • MTL-Insert • 2145-900 Rev. D • 3/08

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents What to do if you smell gas Model MTL-InsertHOT Surfaces Xxxxxxxx Homeowner Reference InformationTable of Contents Listing and Code Approvals Inspect Appliance and Components Design and Installation ConsiderationsGetting Started Tools and Supplies NeededMinimum Fireplace Opening Fireplace Size RequirementsClearances to Mantels or other Combustibles above Appliance ClearancesVent Termination Minimum Clearances Termination LocationsMeasuring Standards Vent Information and DiagramsVent Table Key Horizontal VentingInstallation Preparation Connecting Vent Pipe Installing Vent Pipe and ApplianceVenting Components Placing, Securing and Leveling the Appliance Class a Pipe Installing Termination CapFactory Built Wood Burning Damper Flashing Kit OptionalFuel Conversions Gas Connection Gas InformationGas Pressures Check for GAS Leaks High Altitude InstallationsAppliance Requirements Wiring the ApplianceON/OFF Switch Electrical InformationOptional Accessories Optional Junction Box InstallationVariable Speed Control Junction BOX BLK Mantel Projections FinishingEmber Placement Appliance SetupClean the Appliance AccessoriesPositioning the Logs Log Set Assembly LOGS-SXTHeat & Glo MTL-Insert 2145-900 Rev. D 3/08 Heat & Glo MTL-Insert 2145-900 Rev. D 3/08 Replacing Glass Assembly Glass AssemblyAir Shutter Setting Removing Glass AssemblyBefore Lighting Appliance Operating InstructionsBefore operating this appliance have a qualified technician Standing Pilot Ignition Lighting ApplianceWhat to do if YOU Smell GAS Check Pilot Flame Appearance Initial Break-in ProcedureAfter Appliance is Lit Issue Solutions Frequently Asked QuestionsSymptom Possible Causes Corrective Action TroubleshootingStanding Pilot Ignition System Symptom Possible Cause Corrective Action TroubleshootingMaintaining and Servicing Appliance Maintenance TasksDoors, Surrounds Inspect Maintenance TasksReference Materials Appliance Dimension DiagramDirect Vent Flex Liner Kits Vent Kits ComponentsService Parts Log Set AssemblyPart number list on following Stocked Service PartsAt Depot Standing Pilot Valve Assembly Limited Lifetime Warranty Heat & GLO GAS Appliance Products Limited Lifetime WarrantyContact Information

MTL-INSERT specifications

The Heat & Glo LifeStyle MTL-INSERT is a remarkable gas fireplace insert that combines elegance, innovation, and cutting-edge technology to enhance the comfort and atmosphere of your home. Designed to seamlessly fit into existing masonry or factory-built fireplaces, the MTL-INSERT transforms any living space with minimal installation effort, making it a practical choice for both renovations and new builds.

One of the standout features of the LifeStyle MTL-INSERT is its contemporary style, which includes clean lines and a sleek facade. This insert is available in various sizes and configurations, allowing homeowners to select the ideal fit for their specific fireplace and aesthetic needs. The large viewing area provided by the expansive glass front ensures that the mesmerizing dance of the flames can be enjoyed from multiple angles in any room.

The MTL-INSERT is equipped with a powerful heat output, efficiently warming spaces without the need for additional heating sources. It utilizes advanced heat distribution technologies, including a blower system that circulates warm air throughout the room, making it not only a beautiful addition but also a functional one. With an impressive BTU range, it excels in heating capacities, ensuring comfort even in colder climates.

One of the key innovations of the LifeStyle MTL-INSERT is its use of the IntelliFire® technology. This patented system allows for easy control of the fireplace with a remote control, wall switch, or smart home integration, providing convenience and accessibility. The IntelliFire® technology also features an automatic ignition system, allowing for fast and reliable lighting of the flames without the hassle of manual starters.

Additionally, the LifeStyle MTL-INSERT is designed with safety and efficiency in mind. The unit is equipped with an oxygen depletion sensor (ODS) that automatically turns off the gas supply if the oxygen levels in the room become too low. This ensures peace of mind while enjoying the warmth and ambiance of the fireplace.

With environmentally friendly options, including a variety of fuel types such as natural gas or propane, the MTL-INSERT can cater to different homeowner preferences while maintaining optimal efficiency. The incorporation of high-quality materials and craftsmanship guarantees durability and longevity, ensuring that this investment will serve as a centerpiece in your home for years to come.

In conclusion, the Heat & Glo LifeStyle MTL-INSERT stands out as an exceptional choice for those seeking a modern and efficient gas fireplace insert. Its blend of advanced technologies, stylish design, and powerful heating capabilities make it a sought-after addition to any home, providing both comfort and an inviting atmosphere that families can enjoy together.
Top Page Image Contents