Table of Contents

Section 6 Maintenance

•Long-term exposure to vapors can cause serious injury and illness.

•Avoid prolonged breathing of vapors.

•Keep face away from nozzle and gas tank opening.

•Keep gas away from eyes and skin.

Filling the Fuel Tank

Refer to Figure 6-4

The fuel tank is located on the left side under the seat console. Total fuel capacity is 8 gallons.

When filling the fuel tank, place gear shift in 1st or reverse gear, set park brake, turn off engine and remove ignition key. Tilt seat console forward to access fuel tank. Clean dirt from around fuel cap, remove cap and begin filling. When finished, screw cap back on securely and wipe up any spilled gasoline. Use regular unleaded gasoline with an octane rating of 87 or higher.

IMPORTANT: Never use methanol, gasoline containing methanol and/or gasohol containing more than 10% ethanol. These fuels can damage the vehicle’s fuel system. Do not mix oil with gasoline.

Using a fuel stabilizer/conditioner in the vehicle can provide benefits such as:

1.Keeps gasoline fresh during storage of 90 days or less. The fuel tank should be emptied for longer storage.

2.Cleans the engine during operation.

3.Eliminates gum-like varnish build-up in the fuel system.

IMPORTANT: Do not use fuel additives containing methanol or ethanol.

Add the correct amount of gas stabilizer/conditioner to the gas. Follow the gas stabilizer/conditioner manufacturer’s directions for best results.

Emptying the Fuel Tank

!DANGER

Never siphon a fuel tank by sucking on a hose with your mouth. Gasoline is a poison. Also fuel vapors and gas are harmful to your lungs and can permanently damage them. Always use a siphon pump.

The fuel tank will need emptying when preparing for long term storage or replacing a damaged one.

1.Prepare vehicle for maintenance as outlined in steps 1-6 on page 24.

2.Follow all Fuel Safety Cautions, Warnings and Dangers.

3.Remove fuel cap and siphon fuel through the fuel fill opening with a siphon pump into an approved gas container. Make sure the container is capable of holding all the gas. Do not dump fuel on the ground.

Fuel Cap andFuel Filter Fuel Fill Opening

Fuel Gauge

22080

Figure 6-4

Fuel Filter and Fuel Line Maintenance

Refer to Figure 6-5

The fuel filter (Land Pride Part No. 831-031C) is installed in the fuel line between the fuel tank and engine and should be replaced annually. At the same time check the fuel line hoses for any cracks or leaks. Inspect and replace fuel filter and fuel lines as follows:

1.Prepare vehicle for maintenance as outlined in steps 1-6 on page 24.

2.Safely secure the seat console in the raised position.

3.Following all Fuel Safety Cautions and Warnings, remove clamps securing the fuel filter and remove fuel filter for inspection.

4.Check fuel filter for sediment and water accumulation. Check fuel lines for cracks and leaks.

5.Replace damaged fuel lines with new ones.

6.Replace fuel filter when sediment or water is present.

7.Reattach fuel filter to fuel line with arrow on the filter pointing in the same direction fuel flows in the line. Fuel flows towards the engine.

8.Install hose clamps around fuel filter.

9.Start vehicle and inspect for fuel leaks along fuel line and fuel filter.

10.Shut off vehicle and remove wheel chocks if used.

22079

Figure 6-5

28

4400EX Heavy Duty Off Road Utility Vehicle 720-132M

7/01/05

Page 29 Page 31
Page 30
Image 30
Land Pride 720-132M, 22076, 22081 manual Filling the Fuel Tank, Emptying the Fuel Tank, Fuel Filter and Fuel Line Maintenance
Page 29 Page 31

22081, 22076, 720-132M specifications

Land Pride is renowned for its high-quality agricultural and landscaping equipment, and among its impressive lineup, the Land Pride 720-132M mower stands out as a versatile solution for various mowing applications. Designed with performance and efficiency in mind, the 720-132M mower is perfect for both residential and commercial users looking for a reliable machine capable of handling diverse terrain and mowing conditions.

One of the key features of the 720-132M is its robust cutting deck, which measures 132 inches in width. This wide cutting capability allows for expansive mowing coverage in fewer passes, significantly reducing mowing time and increasing productivity. The deck is constructed from heavy-duty materials, ensuring durability and longevity even when used in challenging environments.

Equipped with a high-performance cutting system, the mower boasts engineered blades that provide a clean and precise cut, promoting healthier lawn growth. The unique blade overlap design ensures consistent cutting performance across the entire width of the deck, reducing the likelihood of uncut areas left behind.

The Land Pride 720-132M features adjustable cutting height settings, giving operators the flexibility to adapt the mower to various grass types and desired finish quality. This adjustability is crucial for achieving optimal results, especially when transitioning from different mowing conditions.

Safety is a top priority for Land Pride, and the 720-132M integrates several safety features to protect both the operator and the equipment. Its robust frame design provides stability during operation, while operator presence controls ensure the mower stops when the operator leaves the seat, mitigating the risk of unintended accidents.

The mower is compatible with a wide range of tractors, allowing for seamless integration with existing equipment. Its simple attachment system enables quick mounting and dismounting, making it user-friendly and convenient for varying mowing tasks.

Another notable technology in the 720-132M is its efficient power transfer system. The mower is designed to maximize performance while minimizing wear and tear on the tractor, ensuring that operators can tackle their mowing tasks with confidence and ease.

Overall, the Land Pride 720-132M mower, with its advanced technologies and features, stands out as a leading choice for those seeking reliable and efficient mowing solutions tailored to both professional and personal landscaping needs.
Top Page Image Contents