Table of Contents

Section 6 Maintenance

Engine Torques

For engine torque values, see engine owner’s manual.

All Other Torques

For all other torques refer to “Torque Values Chart” page 48.

6.Work may now be performed on the vehicle. Be sure to properly torque all bolts that were loosened. Wheel bolts should be torqued after the vehicle is lowered to the ground.

7.Lower the vehicle by first jacking the vehicle up high enough to remove the jack stands. Then carefully lower the jack until the vehicle is on the ground.

Tire Maintenance

Use only tires recommended by Land Pride.

It is important for your safety and the safety of others that the tires have correct air pressure. Check air pressure in all four tires before each use. Visually inspect tires for loss of air throughout each day of operation. See Tire Inflation Chart below for correct tire pressure.

Tire Inflation Chart

Tire

Inflation PSI

 

 

Front Tires

15*

 

 

Rear Tires

20*

 

 

*Maximum tire pressure is noted on tire side wall.

Jacking the Vehicle

!DANGER

For your safety and safety of others, a jacked vehicle must be supported properly with jack stands before working under and around it. Also the wheels on the ground must be chocked on both sides to prevent the vehicle from rolling forward or backward.

IMPORTANT: Use a hydraulic jack, floor jack, or scissor type jack to lift vehicle. Do not use a handyman jack or bumper jack and don’t jack against the bumper, body, differential case, axles or hydraulic lines.

1.Prepare vehicle for maintenance as outlined in steps 1-6 on page 24.

2.Loosen the lug nuts on a wheel being removed approximately 1/2 turn counterclockwise while it is still on the ground.

3.See important note above. Place proper jack under vehicle as follows:

a.Front tires: Refer to Figure 6-1.Place jack under the main frame just behind the axle.

b.Rear tires: Refer to Figure 6-2.Place jack under the main frame just in front of the axle.

4.Jack vehicle only high enough to do the work intended.

5.Support vehicle securely with jack stands before working under and around the vehicle.

8. Remove wheel chocks.

.

21350

Figure 6-1

21351

Figure 6-2

Seat Belts

Refer to Figure 4-7and Figure 4-8on page 17

Periodically check the seat belt webbing, retractor, buckle and mounting hardware for wear and damage. Always check seat belts for wear and damage after a collision. Replace a damaged seat belt with genuine Land Pride parts before putting the vehicle back into service.

Occasionally the seat belt webbing can become twisted, tangled or jammed. Free seat belt webbing before putting the vehicle into service using the following procedures:

1.Pull the lap belt all the way out of the retractor. Untwist the belt and remove any objects that are jamming the belt.

2.Hand feed the lap belt into the retractor. If the belt does not fully retract, pull it out and retract until it is completed retracted.

3.Once the belt has retracted, pull it fully out again and feed it back into the retractor several more times to make sure it is working properly.

7/01/05

4400EX Heavy Duty Off Road Utility Vehicle 720-132M 25

Page 26 Page 28
Page 27
Image 27
Land Pride 720-132M, 22076, 22081 manual Tire Maintenance, Jacking the Vehicle, Seat Belts, Engine Torques All Other Torques
Page 26 Page 28

22081, 22076, 720-132M specifications

Land Pride is renowned for its high-quality agricultural and landscaping equipment, and among its impressive lineup, the Land Pride 720-132M mower stands out as a versatile solution for various mowing applications. Designed with performance and efficiency in mind, the 720-132M mower is perfect for both residential and commercial users looking for a reliable machine capable of handling diverse terrain and mowing conditions.

One of the key features of the 720-132M is its robust cutting deck, which measures 132 inches in width. This wide cutting capability allows for expansive mowing coverage in fewer passes, significantly reducing mowing time and increasing productivity. The deck is constructed from heavy-duty materials, ensuring durability and longevity even when used in challenging environments.

Equipped with a high-performance cutting system, the mower boasts engineered blades that provide a clean and precise cut, promoting healthier lawn growth. The unique blade overlap design ensures consistent cutting performance across the entire width of the deck, reducing the likelihood of uncut areas left behind.

The Land Pride 720-132M features adjustable cutting height settings, giving operators the flexibility to adapt the mower to various grass types and desired finish quality. This adjustability is crucial for achieving optimal results, especially when transitioning from different mowing conditions.

Safety is a top priority for Land Pride, and the 720-132M integrates several safety features to protect both the operator and the equipment. Its robust frame design provides stability during operation, while operator presence controls ensure the mower stops when the operator leaves the seat, mitigating the risk of unintended accidents.

The mower is compatible with a wide range of tractors, allowing for seamless integration with existing equipment. Its simple attachment system enables quick mounting and dismounting, making it user-friendly and convenient for varying mowing tasks.

Another notable technology in the 720-132M is its efficient power transfer system. The mower is designed to maximize performance while minimizing wear and tear on the tractor, ensuring that operators can tackle their mowing tasks with confidence and ease.

Overall, the Land Pride 720-132M mower, with its advanced technologies and features, stands out as a leading choice for those seeking reliable and efficient mowing solutions tailored to both professional and personal landscaping needs.
Top Page Image Contents