Heat & Glo LifeStyle MTL-INSERT owner manual Lighting Appliance, Standing Pilot Ignition

Page 26

B. Lighting Appliance

Standing Pilot Ignition

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

LIGHTING

INSTRUCTIONS

1.Turn off all electric power to the appliance.

2.Push in gas control knob slightly and turn clockwise to “OFF”.

A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electric switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•If you cannot reach your gas sup- plier, call the fire department.

C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explo- sion.

D. Do not use this appliance if any part has been under water. Im- mediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

NOTE: Knob cannot be turned from “PILOT” to “OFF” unless knob is pushed in slightly. Do not force.

3.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the Safety Informa- tion located on the left side of this label. If you don’t smell gas, go to next step.

4.Find the pilot. The pilot is inside combustion chamber next to the main burner.

5.Turn knob on gas control counter clockwise

to “PILOT”.

6. Push in control knob all the way and hold in. Im-

mediately depress red or black piezo button. It may

require several depressions of the red or black

piezo button until PILOT lights. If PILOT light does

WARNING: CAUTION:

not light after 10 seconds, return to step 3. Continue to

hold the control knob in for about one minute after the

pilot is lit. Release knob and it will pop back out. Pilot

should remain lit. If it goes out, repeat steps 3 through 6.

DO NOT CONNECT 110 VAC TO THE CONTROL VALVE.

Improper installation, adjustment, al- teration, service or maintenance can cause injury or property damage. Re- fer to the owner’s information manual provided with this appliance.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

If not installed, operated, and main- tained in accordance with the man- ufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which are known to the State of California to cause can- cer, birth defects, or other reproduc- tive harm.

Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

Hot while in operation. Do not touch. Keep children, clothing, furniture, gaso- line and other liquids having flammable vapors away.

Do not operate the appliance with panel(s) removed, cracked or broken. Replacement of the panel(s) should be done by a licensed or qualified service person.

NOT FOR USE

WITH SOLID FUEL

For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.

Also Certified for Installation in a Bedroom or a Bedsitting Room.

For assistance or additional informa- tion, consult a qualified installer, ser- vice agency or the gas supplier.

• If knob does not pop up when released, stop and im-

 

mediately call your service technician or gas supplier.

•

If the pilot will not stay lit after several tries, turn

 

the gas control knob to “OFF” and call your service

 

technician or gas supplier.

7.

Turn gas control knob counterclockwise to

“ON”.

8.To light Burner, flip the on/off switch to the “ON” position, and close access grille.

9.Turn on all electric power to the appliance.

TO TURN OFF GAS TO APPLIANCE

1. Turn off all electric power to the appliance if service is to be performed.

2.

Open control access panel.

3.

Move switch to “OFF” position.

4.

Push in gas control knob slightly and turn clock-

 

wise

to OFF”. Do not force.

For additional information on operating your

Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.

5.

Close control access panel.

 

464-903G

26

Heat & Glo • MTL-Insert • 2145-900 Rev. D • 3/08

Page 25 Page 27
Image 26
Page 25 Page 27
Contents HOT Surfaces Model MTL-InsertWhat to do if you smell gas Homeowner Reference Information XxxxxxxxTable of Contents Listing and Code Approvals Tools and Supplies Needed Design and Installation ConsiderationsGetting Started Inspect Appliance and ComponentsFireplace Size Requirements Minimum Fireplace OpeningClearances Clearances to Mantels or other Combustibles above ApplianceTermination Locations Vent Termination Minimum ClearancesHorizontal Venting Vent Information and DiagramsVent Table Key Measuring StandardsInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Placing, Securing and Leveling the Appliance Damper Flashing Kit Optional Installing Termination CapFactory Built Wood Burning Class a PipeGas Pressures Gas InformationFuel Conversions Gas Connection High Altitude Installations Check for GAS LeaksElectrical Information Wiring the ApplianceON/OFF Switch Appliance RequirementsOptional Junction Box Installation Optional AccessoriesVariable Speed Control Junction BOX BLK Finishing Mantel ProjectionsAccessories Appliance SetupClean the Appliance Ember PlacementLog Set Assembly LOGS-SXT Positioning the LogsHeat & Glo MTL-Insert 2145-900 Rev. D 3/08 Heat & Glo MTL-Insert 2145-900 Rev. D 3/08 Removing Glass Assembly Glass AssemblyAir Shutter Setting Replacing Glass AssemblyBefore operating this appliance have a qualified technician Operating InstructionsBefore Lighting Appliance What to do if YOU Smell GAS Lighting ApplianceStanding Pilot Ignition After Appliance is Lit Initial Break-in ProcedureCheck Pilot Flame Appearance Frequently Asked Questions Issue SolutionsStanding Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Troubleshooting Symptom Possible Cause Corrective ActionMaintenance Tasks Maintaining and Servicing ApplianceInspect Maintenance Tasks Doors, SurroundsAppliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsPart number list on following Log Set AssemblyService Parts At Depot Service PartsStocked Standing Pilot Valve Assembly Limited Lifetime Warranty Limited Lifetime Warranty Heat & GLO GAS Appliance ProductsContact Information

MTL-INSERT specifications

The Heat & Glo LifeStyle MTL-INSERT is a remarkable gas fireplace insert that combines elegance, innovation, and cutting-edge technology to enhance the comfort and atmosphere of your home. Designed to seamlessly fit into existing masonry or factory-built fireplaces, the MTL-INSERT transforms any living space with minimal installation effort, making it a practical choice for both renovations and new builds.

One of the standout features of the LifeStyle MTL-INSERT is its contemporary style, which includes clean lines and a sleek facade. This insert is available in various sizes and configurations, allowing homeowners to select the ideal fit for their specific fireplace and aesthetic needs. The large viewing area provided by the expansive glass front ensures that the mesmerizing dance of the flames can be enjoyed from multiple angles in any room.

The MTL-INSERT is equipped with a powerful heat output, efficiently warming spaces without the need for additional heating sources. It utilizes advanced heat distribution technologies, including a blower system that circulates warm air throughout the room, making it not only a beautiful addition but also a functional one. With an impressive BTU range, it excels in heating capacities, ensuring comfort even in colder climates.

One of the key innovations of the LifeStyle MTL-INSERT is its use of the IntelliFire® technology. This patented system allows for easy control of the fireplace with a remote control, wall switch, or smart home integration, providing convenience and accessibility. The IntelliFire® technology also features an automatic ignition system, allowing for fast and reliable lighting of the flames without the hassle of manual starters.

Additionally, the LifeStyle MTL-INSERT is designed with safety and efficiency in mind. The unit is equipped with an oxygen depletion sensor (ODS) that automatically turns off the gas supply if the oxygen levels in the room become too low. This ensures peace of mind while enjoying the warmth and ambiance of the fireplace.

With environmentally friendly options, including a variety of fuel types such as natural gas or propane, the MTL-INSERT can cater to different homeowner preferences while maintaining optimal efficiency. The incorporation of high-quality materials and craftsmanship guarantees durability and longevity, ensuring that this investment will serve as a centerpiece in your home for years to come.

In conclusion, the Heat & Glo LifeStyle MTL-INSERT stands out as an exceptional choice for those seeking a modern and efficient gas fireplace insert. Its blend of advanced technologies, stylish design, and powerful heating capabilities make it a sought-after addition to any home, providing both comfort and an inviting atmosphere that families can enjoy together.
Top Page Image Contents