PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
1)Read all instructions before using the appliance.
2)To avoid fire or shock hazard, plug the appliance directly into a 120V AC electrical outlet.
3)Keep the cord out of heavy traffic areas. DO NOT let the cord hang over the edge of a table or counter. To avoid fire hazard, NEVER put the cord under rugs, near heat registers, radiator, stoves, or heaters.
4)To protect against electrical hazards, DO NOT immerse in water or other liquids. Do not use near water.
5)Close supervision is necessary when any appliance is used by or near children, or by disabled people.
6)Always unplug the fan before moving it, putting on or taking off parts, cleaning, or whenever the fan is not in use. Be sure to pull by the plug and not the cord.
7)Avoid contact with moving parts. DO NOT operate without fan grills properly in place.
8)DO NOT operate any appliance with a damaged cord or plug, if motor fan fails to rotate, after the appliance malfunctions, or if it has been dropped or damaged in any manner. Return appliance to manu- facturer for examination, electrical or mechanical adjustment, or repair.
9)DO NOT operate in the presence of explosive and/or flammable fumes.
10)Use appliance only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by The Holmes Group may cause hazards.
11)DO NOT use outdoors.
12)Always use on a dry, level surface.
13)Keep unit away from heated surfaces and open flames.
14)WARNING: To reduce the risk of fire or electric shock,DO NOT use this fan with any
THIS PRODUCT IS EQUIPPED WITH A POLARIZED AC (Alternating Current) PLUG (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact qualified personnel to install the proper outlet.
DO NOT DEFEAT THE SAFETY PURPOSE OF THIS
POLARIZED PLUG IN ANY WAY
15)DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user serviceable parts. All servicing should be performed by qualified personnel only.
PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
Base / Pole Assembly
Step 1: Push in the small tab on each foot extension and snap into the stand lock.
Step 2: Insert the hollow end of the lower pole into the stand lock until it won’t go any further.
Step 3: Loosen up the adjustable height nut, raise the extension pole, and tighten the nut.
Step 4: Loosen the upper pole nut. Firmly push the upper pole on to the extension pole and tighten the upper pole nut.
Fan Head Assembly
Step 1: Position the rear grill over the motor shaft, making sure the circular opening in the center of the rear grill fits over the prongs on the rear housing. Please make sure the rear grill fits securely against the motor housing.
Step 2: Secure the rear grill in its place using the rear
Step 3: Slide the fan blade, with the hollowed interior of the blade fac- ing towards the rear of the grill firmly onto the motor shaft, until the shaft protrudes from the front of the blade.
Step 4: Secure the fan blade onto the motor shaft by firmly tightening the fan blade nut.
NOTE: TURN THE BLADE NUT
Step 5: Center the front grill by aligning the Holmes logo on the grill hub so it is horizontal and parallel with the floor. Then, holding the front grill against the rear grill, push the translucent grill ring into place at the top and bottom of the fan. (Push directly on the translucent grill ring, not on the grills
Step 6: Align the metal plate with the indentation on the bottom of the grill ring. Pass the screw with the washer through the opening on the bottom of the grill ring and fasten to the metal plate.