Samsung SSA-P102T Important Safety Instructions, This device may not cause harmful interference

Page 3

5.Keep out of direct sunlight and heat radiation sources. It may cause fire.

6.Install it in a place with good ventilation.

7.Avoid aiming the controller directly towards extremely bright objects such as sun.

8.Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

9.The Mains plug is used as a disconnect device and shall stay readily operable at any time.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :

1)This device may not cause harmful interference, and

2)This device must accept any interference received including interference that may cause undesired operation.

Caution

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in ac- cordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

IMPORTANT SAFETY INSTRUCTIONS

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

13. Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

SAFETY INFORMATION

English _ 3

Image 3
Contents Please visit our website Access Control PanelSafety information Safety informationThis device may not cause harmful interference, Important Safety InstructionsContents Product introduction FeaturesWHAT’S Included Door Open Alarm and Forced Door Open AlarmHoliday Setup Duress ModeMain Board Input #2 Buzzer control settingsPower LED Displays the status of the power supply Input #3Cable Selection Termination Resistor in RS-422 Communication Connecting the Termination Resistor and DiodeTermination Resistor Bypass Diode ConnectionHost PC EARTH-GROUNDING the Communication CablesReader Connection POWER, READER, and I/O ConnectionPower Connection Check the location of the power portInput Connection Output Connection Check the location of the communication port RS-232 Pin Female ConnectorCommunication Line Connection RS-232 Communication Port ConnectionRS-422 Communication Port Connection Standalone RS-232CMAX m SSA-P102 RS-422 Communication Port Connection Multiple UnitsTCP/IP Communication Connection TCP/IP Communication Port ConnectionInitialization Reader Input BIT SetupInitializing the system using the Initialize switch Use the switch to set the valueBoard ID Setting Communication Speed SetupUse the switch to set the value Troubleshooting TroubleshootingProblem Action System is in sync with the PC Service for your helpIrrelevant card number is displayed Properly established D0, D1Product specifications Product SpecificationsCorrect disposal of batteries in this product