GE 60-639-95R-OD, 60-639-43-EUR-OD Programming, Final Testing, Maintenance, Replacing Batteries

Page 6

1.Determine which detection zone/lens segment needs a masking label.

2.Peel the desired mask label from its backing and apply to the inside of the lens segment to be blocked.

Programming

Refer to the panel installation instructions for information on programming the sensor into the

 

panel.

 

 

 

 

 

 

 

 

 

 

 

 

Final Testing

Final testing should be done to verify radio signal integrity and confirm control panel program-

 

ming and response. The actual transmitter range can be determined by performing a sensor test as

 

follows:

 

 

 

 

 

 

 

 

 

 

1. After the sensor has been mounted, remove it from its mounting plate and activate the tamper

 

switch to start the walk test mode.

 

2. Replace the sensor in its mounting plate.

 

3. Place the control panel in test mode. Move across the detection pattern until the sensor’s LED

 

turns on. STOP your motion.

 

4. Listen for the appropriate system response. If the system does not respond, proceed to the

 

“Troubleshooting” section.

 

 

 

Maintenance

At least once a year, the range and coverage should be verified for proper operation. The end user

 

should be instructed to put the sensor in walk test mode and walk through the far end of the cov-

 

erage pattern to verify proper detection.

 

Replacing Batteries

 

When battery replacement is necessary, observe proper polarity (as shown in the battery compart-

 

ment) when installing the new battery. The sensor may be damaged if installed incorrectly. As

 

you look at the battery compartment, on the left side the positive battery end is down and on the

 

right side the positive end is up. When the battery is replaced, wait at least 3 minutes after install-

 

ing the battery before activating the walk test mode. See Figure 8 for battery locations.

 

!

Replace only with two AA 1.5V Alkaline batteries. Dispose of used batteries

 

according to manufacturer’s instructions and local government authorities.

 

 

 

 

 

 

 

 

 

 

 

Caution

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PIR

 

 

2

AA

 

 

 

Cover

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ba

tt

1

.5 V

 

 

 

 

 

 

e

 

 

ol

 

 

 

 

 

ries

 

t

 

 

 

 

 

 

 

 

 

 

PWB

 

 

 

 

 

 

 

 

 

 

Cover

 

 

 

 

 

 

 

Lens

 

 

 

 

 

 

 

 

 

Tabs

Sensor

Body

Tamper

Switch

Mounting

Plate

Figure 8. PIR Components

Troubleshooting Follow these guidelines if the system does not respond correctly when the sensor is activated.

•Check programming and re-program sensor into panel if necessary.

•Move the sensor to another location and test for correct response.

6

Indoor/Outdoor PIR Motion Sensors Installation Instructions

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Installation Indoor Installation GuidelinesProduct Summary Outdoor Installation Guidelines Mounting Use the following procedure to mount the sensor Indoor Motion Sensor Lens Replacement Setting the SensitivityAnimal Alley Lens Guidelines Coverage TestingOutdoor Motion Sensor MaskingProgramming Final TestingMaintenance Replacing BatteriesSpecifications Declaration of ConformityMeans of Conformity Approved for use in the countries marked with a check

60-639-95R, 60-639-43-EUR, 60-639-43-EUR-OD, 60-639-95R-OD specifications

The GE 60-639-43-EUR-OD and its associated models, including the 60-639-43-EUR, 60-639-95R, and 60-639-95R-OD, represent a significant advancement in engineering solutions from General Electric, designed to meet diverse industrial needs. These models are recognized for their robust functionality and reliability in demanding operational environments.

One of the main features of these models is their versatility in application. They are engineered to cater to a variety of sectors including manufacturing, transportation, and energy. Their adaptability allows them to be seamlessly integrated into existing systems, offering enhanced performance without requiring extensive modifications.

The GE 60-639 series is fortified with advanced technologies that enhance efficiency and productivity. Key among these technologies is their use of smart monitoring systems, which provide real-time data and insights into performance metrics. This feature not only aids in predictive maintenance, minimizing downtime but also optimizes the overall workflow.

In terms of characteristics, these models are designed with a focus on energy efficiency. They utilize innovative power management technologies that reduce energy consumption while maintaining peak performance. This not only lowers operational costs but also aligns with global sustainability efforts aimed at reducing carbon footprints.

Moreover, the build quality of the GE 60-639 series is exceptional. They are constructed using high-grade materials that ensure durability and resilience against harsh operational conditions. This ruggedness translates into longer service life and lower replacement costs, making them a wise investment for businesses.

The user interface of these models is intuitive, allowing for easy operation and management. With streamlined controls and comprehensive diagnostic features, users can effectively monitor and manage system performance with minimal training.

In conclusion, the GE 60-639-43-EUR-OD, along with its counterparts, exemplifies GE’s commitment to innovation and reliability. With their versatile application, advanced technologies for efficiency, and robust construction, these models stand out as ideal solutions for modern industrial challenges. Organizations looking to enhance their operational capabilities would benefit significantly from integrating these reliable systems into their operations.
Top Page Image Contents