Goodman Mfg Goodman 90%-95% Gas Furnace Units, GCVC9/GMVC95 Furnace Specifications ACVC9

FURNACE SPECIFICATIONS			ACVC9
	M O D E L	A C V C 90 70 4C X *	A C V C 90 90 5D X *
	B tuh Input (U S ) High F ire	69,000	92,000
	O utput (U S ) High F ire	65,300	86,500
	B tuh Input (U S ) Low F ire	48,000	64,000
	O utput (U S ) Low F ire	45,000	60,100
	A . F .U .E .	93. 3%	92. 7%
	R ated E x ternal S tatic (" w .c .)	.10 - .50	.10 - .50
	Tem perature Ris e (°F )	30 - 60	30 - 60
	H igh S tage P res s ure S witc h Trip P oint (" w .c . )	-0. 55	-0 .55
	Low S tage P res s ure S w itc h Trip P oint (" w . c .)	-0. 20	-0 .20
	F ront Cover P res s ure S witc h Trip P oint (" w .c )	-0. 37	-0 .37
	B lower W heel (D " x W ")	10 x 10	11 x 10
	B lower H ors epower	3/4	1
	B lower S peeds	R efer to airflow c harts in this m anual.
	M ax C F M @ 0.5 E .S .P .
	P ow er S upply	115-60 -1	115-60 -1
	M inim um Circ uit A m pac ity (M CA )	14 .1	14 .4
	M ax im um O verc urrent Devic e	15	15
	Trans form er (V A )	40	40
	H eat A ntic ipator (A m ps )	0. 7	0 .7
	P rim ary Lim it S etting (°F )	160	170
	A ux iliary Lim it S etting (°F )	220	180
	R ollout Lim it S etting (°F )	220	210
	F an D elay O n H eating	30 s ec s .	30 s ec s .
	O ff Heating *	150 s ec s .	150 s ec s .
	F an D elay O n C ooling	5 s ec s .	5 s ec s .
	O ff Cooling	45 s ec s .	45 s ec s .
	F an D elay O n - F an O nly	5 s ec s .	5 s ec s .
	G as S upply P res s ure (N atural/P ropane) (" w .c .)	7 / 11	7 / 11
	M anifold P res s ure (N atural/P ropane) H igh S tage (" w . c . )	3 .5 / 10	3 .5 /10
	M anifold P res s ure (N atural/P ropane) Low S tage ("w .c .)	1. 9 / 6 .0	1 .9 / 6 .0
	O rific e S iz e (N atural/P ropane)	#43 / #55	#43 / #55
	N um ber of B urners	3	4
	V ent Connec tor D iam eter (inc hes )	2	2
	C om bus tion A ir Connec tor D iam eter (inc hes )	2	2
	S hipping W eight (lbs .)	157	172

* O ff H e a tin g - Th is fa n d e la y tim in g is a d ju s ta b le (9 0 , 1 2 0 , 1 5 0 o r 1 8 0 s e co n d s ), 1 5 0 s e co n d s a s s h ip p e d .

1.These furnaces are manufactured for natural gas operation. Optional Kits are available for conversion to propane gas operation.

2.For elevations above 2000 ft. the rating should be reduced by 4% for each 1000 ft. above sea level. The furnace must not be derated, orifice changes should only be made if necessary for altitude.

3.The total heat loss from the structure as expressed in TOTAL BTU/HR must be calculated by the manufactures method in accordance with the "A.S.H.R.A.E. GUIDE" or "MANUAL J-LOAD CALCULATIONS" published by the AIR CONDITIONING CONTRACTORS OF AMERICA. The total heat loss calculated should be equal to or less than the heating capacity. Output based on D.O.E. test procedures, steady state efficiency times output.

4.Minimum Circuit Ampacity calculated as: (1.25 x Circulator Blower Amps) + I.D. Blower Amps.

20