Louisville Tin and Stove DVCF407B-R PEK KIT Instructions, Units with Terminal Board Step #

Page 15

14-PEK KIT INSTRUCTIONS

(14’ PLUG EXTENSION KIT)

FOR NON-RECESSED INSTALLATIONS ONLY

90Degree

Outside Corner

1

3FT.

SECTION

2

3FT.

SECTION

3

BOTTOM

SECTION 4

UNITS WITH TERMINAL BOARD

STEP #

1.Turn heater off following Section 3 in “Lighting Instructions” and allow to cool.

2.Turn off all electricity to heater.

3.Remove top louver assembly, fan shroud and fan blade.

4.Loosen two screws on romex connector.

5.Remove junction box cover plate.

6.Disconnect three power cord terminals and pull power cord out of top of heater.

7.Insert power cord provided in kit through romex connector and plug onto terminal board following wiring diagram found in lighting and operating instructions.

8.Tighten two screws on romex connector.

9.Replace junction box cover plate.

10.Replace fan blade, fan shroud and top louver assembly.

11.Snap 90 degree outside corner (Ref. 1) onto 3 foot section (Ref. 2) plastic raceway. Insert power cord and remove blue backing from adhesive strip on raceway and apply to side of heater.

12.Insert power cord into second 3-foot section of raceway (Ref. 3) and remove blue backing and apply to side of heater, butting up against bottom of other section.

13.Cut 14-inch long bottom section to required length (see chart), insert power cord, remove backing and apply to side of heater.

14.Plug power cord into wall receptacle.

15.Light the heater following lighting instructions.

 

LENGTH OF BOTTOM

 

SECTION (REF. 4)

MODEL NO.

PLASTIC RACEWAY

DVCF40

5-5/16 Inches

DVCF55

14 Inches

DVCF65

14 Inches

NOTE: Above lengths terminate approximately 2 inches above floor.

Page 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents NAT. GAS DVCF403B-R DVCF653B-R DVCF404B-R DVCF654B-R NAT. GAS DVCF407B-R DVCF557B-R DVCF408B-R DVCF558B-RWhat to do if YOU Smell GAS Introduction ContentsSafety Rules Vent Terminal Clearances Floor ClearancesDIA Wall Installation Electrical ROUGH-INLocations ROUGH-IN GAS SupplyGAS Connection Installing the FurnaceThermostat Installation Locate Vent OpeningTo Turn OFF GAS to Appliance Lighting InstructionsA fire or explosion Pilot Adjustment To Remove Main Burner forProper Burner Flame DVCF403B, DVCF404B Standing Pilot Pictorial SchematicDVCF403 DVCF404 Ladder Schematic DVCF653 DVCF654 Ladder SchematicMotor DVCF407 DVCF408 Ladder SchematicDVCF557 DVCF558 Ladder Schematic DVCF407B, DVCF408BTerminal Block Wiring Diagram Manual Reset SwitchMaintenance Instruction ROUGH-INS for Side Discharge Side KIT no SRB Side Register W/BOOTOptional Side Discharge Kits Side Discharge on Casing KIT no SR Side Register Flush14’ Plug Extension KIT For NON-RECESSED Installations only PEK KIT InstructionsUnits with Terminal Board Step # Symptom Possible Causes Corrective Action Trouble Shooting ChartSymptom Possible Causes Corrective Action Service RecordDVCF40B-R, DVCF55B-R, DVCF65B-R Series Spark Igniter Thermostat Burner AssemblyDirect Vent Counterflow Wall Furnace Vent AssemlbyPart List Part Description Price HOW to Properly Order PartsPart Description Critical Safety Points to Remember Your GAS Control and Pilot Light SystemTampering is Dangerous Table a Louisville TIN and Stove Company

DVCF557B-R, DVCF653B-R, DVCF654B-R, DVCF403B-R, DVCF408B-R specifications

The Louisville Tin and Stove DVCF series offers a range of innovative and versatile vented gas fireplaces, designed to enhance the aesthetic appeal and comfort of any space. Key models in this series include the DVCF404B-R, DVCF654B-R, DVCF653B-R, DVCF557B-R, and DVCF407B-R. Each fireplace is engineered with advanced features and technologies, ensuring an efficient and enjoyable heating experience.

The DVCF404B-R is a compact yet powerful model, perfect for smaller areas. It delivers a heat output of up to 30,000 BTUs, providing ample warmth while maintaining energy efficiency. Its sleek design and modern appearance make it an attractive focal point in any room. The DVCF654B-R, on the other hand, boasts a larger heating capacity, ideal for more spacious environments. With BTUs reaching 38,000, this fireplace ensures that larger areas remain comfortably warm even during harsh winter months.

The DVCF653B-R combines functionality with elegance, featuring a contemporary linear design that fits well into various interior styles. Its advanced venting technology ensures easy installation and optimal performance, allowing homeowners to enjoy the flames' beauty without compromising on safety or efficiency. Meanwhile, the DVCF557B-R is particularly noteworthy for its customizable options, which enable users to choose from various finishes and decorative media, personalizing their fireplace to match their unique tastes.

Lastly, the DVCF407B-R offers a blend of traditional and modern aesthetics, making it a versatile choice for different decor styles. Its efficient heating capabilities and advanced safety features, such as automatic shut-off and a glass front for reduced emissions, make it a reliable option for families.

Overall, the Louisville Tin and Stove DVCF series not only enhances home decor but also prioritizes efficiency, safety, and ease of use. Each model embodies quality craftsmanship and modern technological advancements, making them exceptional choices for anyone looking to invest in a gas fireplace. The comprehensive features, from customizable designs to high BTU outputs, make the DVCF series a standout in the market for homeowners seeking comfort and style.
Top Page Image Contents