Superior VFGL-24MSP-4 SERIES* Operating Instructions, Stop! Read the safety information above

OPERATING INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY

RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

A.This heater has a pilot which must be lit by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE OPERATING smell all around the heater area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electric switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, do not try to repair it, call a qualified service technician. Forced or attempted repair may result in a fire or explosion.

D.Do not use this heater if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

14

	LIGHTING INSTRUCTIONS
1. Stop! Read the safety information above.
	8. With the control knob pressed in, push in and release the
	piezo igniter button to light the pilot.

2.Make sure manual shut-off valve is fully open.

			9.	Hold the control knob in for a further 10 seconds to prevent
3.	Locate gas control knob and piezo.			the flame failure detector from shutting off the gas while the
				probe is warming up.
4.	Depress control knob in and turn clockwise	to the	10.	Release the control knob while turning counterclockwise
	“OFF” position (Figure 19 ).
				to the "ON" Position (Figure 22 ). Then adjust
5. Wait 5 minutes to clear out any gas. Then smell for gas,				"HI"-"LOW" knob to prefered setting.
	including near the floor. If you smell gas, STOP! Follow “B” in			• If the knob does not pop out when released, stop and
	the safety information above. If you do not smell gas, go to the
				immediately call your service technician or gas supplier.
	next step.
6.	The pilot is located on the right side in front of the burner			• If the pilot will not stay lit after several tries, depress and
				turn the gas control knob clockwise		to “OFF”
	(Figure 20 ).			and wait 30 seconds. Depress and turn
7.	Depress control knob in and turn counterclockwise			knob counterclockwise	to
				“IGN” and press igniter button again. If
	to the “PILOT” position (Figure 21 ). Press the control knob all			your pilot does not relight depress and
	the way in for 5 seconds.			turn control knob clockwise
	Note: If you are running the heater for the first time it will be			to “OFF” and call your service technician or gas supplier.
	necessary to press the control knob all the way in for 30		11.	Wait 30 seconds before readjusting the heater when the
	seconds to allow air to bleed out of the gas piping.			control knob has been turned down to a lower setting.

TO TURN OFF GAS TO APPLIANCE

1.Depress and turn control knob clockwise to the “OFF” position (Figure 19 ).

		MANUAL MATCH LIGHTING PROCEDURE — EMERGENCY ONLY
1.	If the pilot cannot be lit with the piezo igniter, the heater can be		3.	Light the match and hold the flame to the end of the pilot and
	manually lit with a match.			ignite the pilot.
2.	With the right hand, depress and turn the control knob		4.	Continue to hold control knob for an additional 10 seconds to
	counterclockwise	to the “ON” position. Hold in the		insure pilot remains lit.
	knob.		5.	Release the control while turning control knob to desired
				setting.