Superior SSDVT-3328CNM manual Install Logs, Volcanic Stone, Glowing Embers, Reference

Page 7

INSTALL Logs, VOLCANIC STONE and

GLOWING EMBERS

Carefully position the ceramic fiber logs and twigs over the burner according to the following steps, while referring to Figure 7.

1.Set the rear log on the raised log support brackets at the rear of the firebox, fitting the slots in the logs over the brackets.

2.Position the front log with the pins for the two side twigs in the up position, and the two vertical burner tabs recessed into the two notches at the rear of the log. Check for recessing of brackets into log notches (by touch) to verify correct log placement.

3.Insert the alignment hole of the left twig over the front log's left pin. Rotate the left twig until it just touches the edge of the ember bracket.

4.Insert the alignment hole of the right twig over the front log's right pin. Rotate the right twig until it almost touches the front panel glass.

Note: Proper twig placement is critical in the gaps between the flame peaks and should be positioned so that at no time they impinge the flames.

Glowing Ember/Volcanic Stone Placement

Remove the replacement rockwool (Glowing Embers) from the packaging and tear into quarter size pieces (see Figure 8 ).

Spread rockwool (quarter-sized pieces) on and along the length of the burner screen. Do not use more than is necessary. To many quarter- sized pieces on the front burner section will cause poor combustion.

When properly positioned, the rockwool will unevenly cover approximately 85% of the burner screen, with no appreciable gaps or openings.

To install Decorative Volcanic Stone, mound up a portion of the volcanic stone in front of the burner in a pattern to suite individual taste.

WARNING

Logs get very hot and will remain hot up to one hour after gas supply is turned off. Handle only when logs are cool. Turn off all electricity to the appli- ance before you install grate and logs.

WARNING

DO NOT attemptto install the logs until the appliance installation has been completed, the gas line connected and tested for leaks and the initial burner operation has been checked out.

WARNING

The size and position of the log set was engineered to give the appli- ance a safe, reliable and attrac- tive flame pattern. Any attempt to use a different log set in the fireplace will void the warranty and will result in incomplete combustion, sooting, and poor flame quality.

WARNING

This appliance is not designed to burn wood. Any attempt to do so could cause irreparable damage to appliance and prove hazardous to your safety.

Separate into Quarter

Size (separate) Pieces

Bag of Glowing

Embers (rockwool)

Figure 8 - Glowing Embers

REFERENCE

Firebox Accessories / Parts

Cat. No.

Model No.

Description

 

 

 

88L53

FGE

Bag of Glowing Embers

 

 

(1 oz. rockwool)

 

 

 

80L42

FDVS

Bag of Decorative

Volcanic Stone

 

 

 

 

 

Table 8

Figure 7 - Log Set (Shown With Optional Log Rack)

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 725,045M REV. N/C 09/2007 For Your Safety What to do if you smell gasOTL Report No -F-29-5 Table of Contents Burn-in Period Gas Controls / Control Compartment AccessOperation and care of your appliance See Maintenance Schedule, MaintenanceGlass Door Front Glass Enclosure Panel, Removal and InstallationInstalling Glass Enclosure Panels Removing Glass Enclosure PanelsGlowing Embers Install Logs, Volcanic StoneGlowing Ember/Volcanic Stone Placement Firebox Accessories / PartsPage Flame Appearance and Sooting Burner AdjustmentsAir Shutter Adjustment Guidelines Burner Air Shutter Adjustment ProcedureWiring Diagram Electronic Pilot AssemblyWarranty Replacement parts Wiring DiagramsMillivolt Wiring Diagram Schematic Representation OnlyPage Accessory Components Product Reference Information Accessory Components Forced Air Kit Arch Door KitsPiece Door Trim Kits Touch-Up Paint KitWhat to do if YOU Smell GAS For Your Safety Read Before LightingLighting Instructions To Turn OFF GAS to AppliancePour Fermer LE GAZ QUI Alimente L’APPAREIL Instructions DallumageFront View Honeywell Electronic Gas Control Valve On / OFF SwitchWhat to do if YOU Smell GAS To shut offFermez la soupape d’arrêt de la canalisation principale Instructions D’ALLUMAGEPour Éteindre L’APPAREIL Fermez la porte du compartiment de contrôle du basManual. Do not touch or attempt to clean glass Maintenance ScheduleMaintenance Task Accomplishing Person Procedure Maintenance TaskSymptom Possible Causes Corrective Action TroubleshootingTroubleshooting Procedure Electronic Ignition System GAS Controls SIT Millivolt Replacement Parts ListNatural Description24 P/N 725,045M REV. N/C 09/2007 Replacement Parts DiagramsWest Taft Avenue Orange, CA

SSDVT-3328CNM specifications

The Superior SSDVT-3328CNM is a cutting-edge solid-state drive designed to elevate storage solutions for both personal and professional applications. This model stands out in a saturated market due to its impressive performance metrics, advanced technologies, and robust durability features.

One of the key highlights of the SSDVT-3328CNM is its exceptional read and write speeds. With sequential read speeds exceeding 3500 MB/s and write speeds reaching 3000 MB/s, this SSD allows for rapid data access and transfer, making it an ideal choice for gamers, content creators, and IT professionals. Whether you are booting up your operating system, loading large files, or running demanding applications, the drive’s speed ensures minimal wait times and improved overall efficiency.

The SSDVT-3328CNM utilizes the NVMe 1.3 interface, which harnesses the full potential of the PCIe 3.0 architecture. This interface facilitates a direct connection between the storage medium and the CPU, eliminating bottlenecks that traditional SATA connections often encounter. As a result, users experience faster file transfers, quicker application launches, and improved responsiveness in multitasking scenarios.

In terms of capacity, the SSDVT-3328CNM features a range of options, including 256GB, 512GB, and 1TB variants, allowing users to select the size that best fits their specific storage needs. The drive's 3D NAND flash technology enhances data durability and reliability. With this technology, memory cells are stacked vertically in a three-dimensional structure, which not only increases storage density but also improves endurance by reducing wear on individual cells.

Reliability is another critical aspect of the SSDVT-3328CNM. Designed with built-in error correction and wear leveling algorithms, this SSD ensures data integrity and prolongs the lifespan of the device. Additionally, with thermal throttling capabilities, the SSD can manage heat effectively, preventing performance dips during demanding tasks.

Security features include AES 256-bit hardware encryption, safeguarding sensitive data against unauthorized access and ensuring compliance with data protection regulations. This makes the Superior SSDVT-3328CNM particularly suitable for business environments.

In summary, the Superior SSDVT-3328CNM combines high performance, cutting-edge technology, and robust security features, making it an excellent choice for anyone in need of reliable and fast storage solutions. Whether for gaming, professional use, or everyday computing, this SSD delivers a cutting-edge experience that meets the demands of modern users.
Top Page Image Contents