Superior SSDVT-3328CNM manual Front Glass Enclosure Panel, Removal and Installation, Glass Door

Page 6

Do not attempt to repaint the appliance until the finish is completely cured (see Burn-In Period on Page 3). If the surface later becomes stained or marred, it may be lightly sanded and touched up with spray paint.

Front Glass Enclosure Panel, Removal and Installation

WARNING

Do not operate appliance with the glass front removed, cracked or broken. Replacement of the glass should be done by a licensed or qualified service technician.

WARNING

Do not attempt to substitute the materials used on this door, or replace cracked or broken glass with any materials other than those provided by the appliance manufacturer.

WARNING

Handle this glass with extreme care! Tempered glass is suscep- tible to damage – do not scratch or handle roughly while rein- stalling the glass door frame.

WARNING

Do not attempt to touch the front enclosure glass with your hands while the fireplace is in use.

WARNING

The glass door of this appli- ance must only be replaced as a complete unit as provided by the manufacturer. Do not attempt to replace broken, cracked or chipped glass separately.

These are direct-vent appliances. They are designed to operate only when the front glass enclosure panel is installed. Generally the front glass enclosure panel should not be removed ex- cept to gain access to the components within the firebox, and the appliance may only be operated without the front glass enclosure panel in place for very brief periods of time during appliance checkout and adjustment.

Note: The flame appearance will be dimin- ished while the front glass enclosure panel is removed.

During this appliance checkout and adjust- ment period, a potential safety hazard exists

-EXERCISE EXTREME CAUTION to prevent the occurrence of any burn injuries from the exposed flames or hot surfaces. Also note, that while the front glass enclosure panel (or any of the panels) is removed, the flame appearance will appear to be smaller than normal.

 

Top Flange on

 

Glass Door

 

Glass Door

Bottom Vee-flange

 

Glass Door

Firebox Floor

 

Glass Door Latch

Figure 6 - INSTALLING GLASS DOOR

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Removing Glass Enclosure Panels

(see Figure 6)

1.Remove the top louver assembly by lifting it up and pulling it out.

2.Remove the control compartment access door (see removal instructions on Page 3 - Removing Control Compartment Door).

3.Locate the two (2) latches at the top of the control compartment. To disengage the two latches from the bottom vee-flange of the glass enclosure panel, reach for the handles located towards the back of the latches and pull the handles down toward the front of the appliance.

4.Swing the bottom of the door out and raise it slightly to lift the top flange of the door frame away from the appliance.

Installing Glass Enclosure Panels

(see Figure 6)

1.Visually inspect the gasket on the backside of the glass panel. The gasket surface must be clean, free of irregularities and seated firmly.

2.Position the glass enclosure panel in front of the firebox opening at a 45 degree angle and engage the top flange over the lip at the top of the firebox opening. See Figure 6.

3.Swing the glass enclosure panel down and back. Ensure the gasket seats evenly as the panel draws shut. Engage the Vee-flange at the bottom of the panel with the latches and close the latches to secure the panel.

4.Reinstall top louver assembly and control compartment door see installation instruc- tions on Page 3, Reinstalling Control Compartment Door).

Page 5 Page 7
Image 6
Page 5 Page 7
Contents For Your Safety What to do if you smell gas 725,045M REV. N/C 09/2007OTL Report No -F-29-5 Table of Contents Gas Controls / Control Compartment Access Burn-in PeriodOperation and care of your appliance Maintenance See Maintenance Schedule,Removing Glass Enclosure Panels Front Glass Enclosure Panel, Removal and InstallationInstalling Glass Enclosure Panels Glass DoorFirebox Accessories / Parts Install Logs, Volcanic StoneGlowing Ember/Volcanic Stone Placement Glowing EmbersPage Burner Air Shutter Adjustment Procedure Burner AdjustmentsAir Shutter Adjustment Guidelines Flame Appearance and SootingElectronic Pilot Assembly Wiring DiagramSchematic Representation Only Wiring DiagramsMillivolt Wiring Diagram Warranty Replacement partsPage Accessory Components Product Reference Information Accessory Components Touch-Up Paint Kit Arch Door KitsPiece Door Trim Kits Forced Air KitTo Turn OFF GAS to Appliance For Your Safety Read Before LightingLighting Instructions What to do if YOU Smell GASInstructions Dallumage Pour Fermer LE GAZ QUI Alimente L’APPAREILTo shut off Honeywell Electronic Gas Control Valve On / OFF SwitchWhat to do if YOU Smell GAS Front ViewFermez la porte du compartiment de contrôle du bas Instructions D’ALLUMAGEPour Éteindre L’APPAREIL Fermez la soupape d’arrêt de la canalisation principaleMaintenance Task Maintenance ScheduleMaintenance Task Accomplishing Person Procedure Manual. Do not touch or attempt to clean glassTroubleshooting Symptom Possible Causes Corrective ActionTroubleshooting Procedure Electronic Ignition System Description Replacement Parts ListNatural GAS Controls SIT MillivoltReplacement Parts Diagrams 24 P/N 725,045M REV. N/C 09/2007West Taft Avenue Orange, CA

SSDVT-3328CNM specifications

The Superior SSDVT-3328CNM is a cutting-edge solid-state drive designed to elevate storage solutions for both personal and professional applications. This model stands out in a saturated market due to its impressive performance metrics, advanced technologies, and robust durability features.

One of the key highlights of the SSDVT-3328CNM is its exceptional read and write speeds. With sequential read speeds exceeding 3500 MB/s and write speeds reaching 3000 MB/s, this SSD allows for rapid data access and transfer, making it an ideal choice for gamers, content creators, and IT professionals. Whether you are booting up your operating system, loading large files, or running demanding applications, the drive’s speed ensures minimal wait times and improved overall efficiency.

The SSDVT-3328CNM utilizes the NVMe 1.3 interface, which harnesses the full potential of the PCIe 3.0 architecture. This interface facilitates a direct connection between the storage medium and the CPU, eliminating bottlenecks that traditional SATA connections often encounter. As a result, users experience faster file transfers, quicker application launches, and improved responsiveness in multitasking scenarios.

In terms of capacity, the SSDVT-3328CNM features a range of options, including 256GB, 512GB, and 1TB variants, allowing users to select the size that best fits their specific storage needs. The drive's 3D NAND flash technology enhances data durability and reliability. With this technology, memory cells are stacked vertically in a three-dimensional structure, which not only increases storage density but also improves endurance by reducing wear on individual cells.

Reliability is another critical aspect of the SSDVT-3328CNM. Designed with built-in error correction and wear leveling algorithms, this SSD ensures data integrity and prolongs the lifespan of the device. Additionally, with thermal throttling capabilities, the SSD can manage heat effectively, preventing performance dips during demanding tasks.

Security features include AES 256-bit hardware encryption, safeguarding sensitive data against unauthorized access and ensuring compliance with data protection regulations. This makes the Superior SSDVT-3328CNM particularly suitable for business environments.

In summary, the Superior SSDVT-3328CNM combines high performance, cutting-edge technology, and robust security features, making it an excellent choice for anyone in need of reliable and fast storage solutions. Whether for gaming, professional use, or everyday computing, this SSD delivers a cutting-edge experience that meets the demands of modern users.
Top Page Image Contents