Burner Adjustments

(QUALIFIED TECHNICIANS ONLY)

Flame Appearance and Sooting

Proper flame appearance is a flame which is blue at the base and becomes yellowish-orange in the body of the flame. When the appliance is first lit, the entire flame may be blue and will gradually turn yellowish-orange during the first 15 minutes of operation. If after a short period the flame stays lowered blue, or if the flame is orange with evidence of sooting (black tip), the air shutter opening may need to be adjusted.

If the air shutter opening is closed too far, sooting may develop. Sooting is indicated by black puffs developing at the tips of very long orange flames. Sooting results in black deposits forming on the logs, appliance inside surfaces and on exterior surfaces adjacent

Figure 9 - Burner Flame Appearance Model SSDV-3328 Series

to the vent termination. Sooting is caused by incomplete combustion in the flames and lack of combustion air entering the air shutter opening. To achieve a warm yellowish-orange flame with an orange body that does not soot, the shutter opening must be adjusted between these two extremes.

Air Shutter Adjustment Guidelines

•If there is smoke or soot present, first check the log set positioning to ensure that the flames are not impinging on any of the logs. If the log set is properly positioned and a sooting condition still exists, then the air shutter opening should be increased.

•The more offsets in the vent system, the larger the air shutter opening will need to be.

•An appliance operated with the air shutter opened too far, may have flames that appear blue and transparent. These weak, blue and transparent flames are termed anemic.

•Propane models may exhibit flames which candle or appear stringy. If this is present and persists, adjust the air shutter to a more closed position, then operate the appliance for a few more minutes to ensure that the flame normalizes and the flames do not appear sooty.

The following chart is provided to aid you in achieving the correct air shutter adjustment for your installation.

Air Shutter Adjustment Guidelines:

Amount of	Flame	Air Shutter
Primary Air	Color	Adjustment

If air shutter is	Flame will	Air shutter
closed too far	be orange	gap should be
		increased
		increased
If air shutter is	Flame will	Air shutter
open too far	be blue	gap should be
		decreased
		decreased

Burner Air Shutter Adjustment Procedure

1. Locate adjustment rod and adjust air shutter to the standard setting as shown in Figure 10 (adjustment rod is located in the lower control compartment).

Note: Rotating the adjustment rod coun- terclockwise increases air and clockwise decreases air.

2.Light appliance (follow lighting procedure on lighting label in control compartment or see pages 16 and 18).

3.Allow the burner to operate for at least 15 minutes while observing the flame continuously to ensure that the proper flame appearance has been achieved (see Figure 9). If the following conditions are present, adjust accordingly.

•If flame appears weak or sooty, adjust the air shutter, incrementally, to a more open position until the proper flame appearance is achieved.

•If flame stays lowered blue, adjust the air shutter, incrementally, to a more closed position until the proper flame appearance is achieved.

4.Leave the control knob (off/pilot/on) in the ON position and the burner OFF/ON switch OFF (& remote switches, if applicable).

5.When satisfied that the burner flame ap- pearance is normal, close the lower control compartment door.

WARNING

Air shutter adjustment should only be performed by a qualified professional service technician.

WARNING

Ensurefrontglasspanelisinplace and sealed during adjustment.

CAUTION

The air shutter door and nearby appliance surfaces are hot. Exer- cise caution to avoid injury while adjusting flame appearance.

CAUTION

Carbon will be produced if the air shutter is closed too much. Any damage due to carboning result- ing from improperly setting the air shutter is not covered under the warranty.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

SSDVT-3328CNM specifications

The Superior SSDVT-3328CNM is a cutting-edge solid-state drive designed to elevate storage solutions for both personal and professional applications. This model stands out in a saturated market due to its impressive performance metrics, advanced technologies, and robust durability features.

One of the key highlights of the SSDVT-3328CNM is its exceptional read and write speeds. With sequential read speeds exceeding 3500 MB/s and write speeds reaching 3000 MB/s, this SSD allows for rapid data access and transfer, making it an ideal choice for gamers, content creators, and IT professionals. Whether you are booting up your operating system, loading large files, or running demanding applications, the drive’s speed ensures minimal wait times and improved overall efficiency.

The SSDVT-3328CNM utilizes the NVMe 1.3 interface, which harnesses the full potential of the PCIe 3.0 architecture. This interface facilitates a direct connection between the storage medium and the CPU, eliminating bottlenecks that traditional SATA connections often encounter. As a result, users experience faster file transfers, quicker application launches, and improved responsiveness in multitasking scenarios.

In terms of capacity, the SSDVT-3328CNM features a range of options, including 256GB, 512GB, and 1TB variants, allowing users to select the size that best fits their specific storage needs. The drive's 3D NAND flash technology enhances data durability and reliability. With this technology, memory cells are stacked vertically in a three-dimensional structure, which not only increases storage density but also improves endurance by reducing wear on individual cells.

Reliability is another critical aspect of the SSDVT-3328CNM. Designed with built-in error correction and wear leveling algorithms, this SSD ensures data integrity and prolongs the lifespan of the device. Additionally, with thermal throttling capabilities, the SSD can manage heat effectively, preventing performance dips during demanding tasks.

Security features include AES 256-bit hardware encryption, safeguarding sensitive data against unauthorized access and ensuring compliance with data protection regulations. This makes the Superior SSDVT-3328CNM particularly suitable for business environments.

In summary, the Superior SSDVT-3328CNM combines high performance, cutting-edge technology, and robust security features, making it an excellent choice for anyone in need of reliable and fast storage solutions. Whether for gaming, professional use, or everyday computing, this SSD delivers a cutting-edge experience that meets the demands of modern users.