Gas Connections

The gas supply lines must meet all requirements of the National Fuel Gas Code (ANSI Z223.1-Latest Edition), or in Canada CAN/CGA B149.1 Natural Gas Installation Code (Latest Edition) or CAN/CGA B149.2 Propane Installation Code (Latest Edition).

The minimum permissible gas supply pressure for the purpose of input adjustment is one (1.0) inch (0.25 kPa) water column above the operating manifold pressure. See the rating plate and gas valve for the manifold pressure and gas type. The maximum permissible gas supply pressure is fourteen (14.0) inches (3.5 kPa) water column for natural gas and liquefied petroleum gases/propane gas.

1.Connect this water heater only to the type of gas (Natural or Propane gas) as shown on the rating plate. Use clean black iron pipe or equivalent material approved by local codes and ordinances. (Dirt and scale from the pipe can enter the gas valve and cause it to malfunction). The inlet gas line must have a minimum length of three (3) inches (7.6 cm) drip leg (sediment trap) installed as close to the water heater’s gas valve as possible. A ground joint union must be installed as close to the water heater as possible in the gas supply line feeding the water heater to permit servicing of the water heater. Compounds used on the threaded joints of the gas piping must be resistant to the action of liquefied petroleum gases/propane gas. DO NOT apply pipe dope to the gas valve inlet and make certain that no pipe dope has become lodged in the inlet screen of the gas valve. Extreme care must be taken to ensure no pipe dope enters the gas valve. Avoid excessive torque when tightening the gas supply line to the gas valve. Excessive torque may result in cracking of the gas valve housing and could create a gas leak. When tightening gas supply line to L.P. control, it is recommended to hold the inlet body of the control securely with an adequate wrench. The suggested maximum torque is 31.5 ft. lbs. (4.4 kg-m).

WARNING

The manufacturer of this water heater will not be liable for any damage or injury caused as a result of a cracked gas inlet as a result of excessive torque.

2.This water heater and its gas connection must be leak tested before placing the water heater in operation. Check for gas leaks with a soap and water solution and a brush or a commercial leak detector fluid. NEVER USE A MATCH OR

OPEN FLAME FOR TESTING!

CAUTION

The water heater and individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of the system at test pressures in excess of 1/2 psi (3.5 kPa). The water heater must be isolated from the gas supply piping system by closing its manual shutoff valve during any pressure testing of the gas supply system at test pressures equal to or less than 1/2 psi (3.5 kPa). The supply line must be capped when not connected to the water heater.

3.While checking for leaks care must be taken to prevent solution from

contacting the electrical connections at the control. If electrical connections at the control become wet, they must be thoroughly dried before attempting to operate the water heater.

Gas Water Heater, 238-47969-00A specifications

The Honeywell 238-47969-00A Gas Water Heater is a premium choice for those seeking efficiency and reliability in their water heating solutions. This model stands out due to its advanced technology and innovative features, making it ideal for residential and commercial applications.

One of the key attributes of the Honeywell 238-47969-00A is its high efficiency design. It utilizes a powerful gas burner system that ensures quick heating of water, reducing wait times for hot water and enhancing user convenience. The energy-efficient operation not only conserves natural resources but also translates to lower utility bills, a benefit that is increasingly important for homeowners and businesses alike.

The water heater is equipped with an advanced control system that allows precise temperature regulation. This feature ensures that the water is heated to the desired temperature without fluctuations, providing consistent performance over time. Additionally, the unit includes a high-quality thermostat that monitors the water temperature, further optimizing energy consumption and performance.

Safety is a top priority for Honeywell, and the 238-47969-00A comes with multiple built-in safety features. These include flame failure protection, which automatically turns off the gas supply in the event of a flame out, and a temperature control mechanism that prevents overheating. Such features provide peace of mind and help guard against potential hazards.

Another noteworthy characteristic of the Honeywell 238-47969-00A is its durability. Constructed with high-grade materials, including corrosion-resistant components, the water heater is designed to withstand the rigors of everyday use. This durability not only extends the lifespan of the unit but also minimizes maintenance requirements.

Installation of the Honeywell gas water heater is straightforward, thanks to its user-friendly design. It is compatible with standard gas lines and is designed for easy integration into existing plumbing systems, which reduces installation time and costs.

In conclusion, the Honeywell 238-47969-00A Gas Water Heater combines efficiency, safety, and durability in a single package. Its advanced technology and user-centric features make it a standout choice in the competitive water heating market, ensuring reliable hot water access for years to come. Whether for a home or a commercial space, this gas water heater is poised to deliver exceptional performance while maximizing energy savings.