Whirlpool WHES48 Water Softener Safety, Your safety and the safety of others are very important

Page 4

Water Softener Safety

Your safety and the safety of others are very important.

We have provided many safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING” These words mean:

You can be killed or seriously injured if you don’t immediatelyfollow instructions.

You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

In the state of Massachusetts: The Commonwealth of Massachusetts plumbing code 248-CMR shall be adhered to. A licensed plumber shall be used for this installation.

In the state of California: You must turn the Salt Efficiency Feature setting to ON. This may initiate more frequent recharges. However, it will operate at 4,000 grains per pound of salt or higher. To turn on the Salt Efficiency Feature, follow the instructions in the “Salt Efficiency” section of this manual.

Before You Start

=The water softener requires a minimum water flow of 3 gallons per minute at the inlet. Maximum allowable inlet water pressure is 125 psi. If daytime pressure is over 80 psi, nighttime pressure may exceed the maximum. Use a pressure reducing valve if necessary (Adding a pressure reducing valve may reduce the flow). If your home is equipped with a back flow preventer, an expansion tank must be installed in accordance with local codes and laws.

=The water softener works on 24 volt, 60 Hz electrical power only, supplied by a direct plug-in transformer (includ- ed). Be sure to use the included transformer and plug it into a nominal 120V, 60 cycle household outlet that is in a dry location only, grounded and properly protected by an overcurrent device such as a circuit breaker or fuse. If transformer is replaced, use only UL, CUL or CSA approved Class 2 transformer with the following specifications:

§Input: 120 VAC, 60 Hz, 13.5 W § Output Voltage: 24 VAC § Output Current: 400 mA

=Do not use this system to treat water that is microbiologically unsafe or of unknown quality without adequate dis- infection upstream or downstream of the system.

European Directive 2002/96/EC requires all electrical and electronic equipment to be disposed of accord- ing to Waste Electrical and Electronic Equipment (WEEE) requirements. This directive or similar laws are in place nationally and can vary from region to region. Please refer to your state and local laws for proper disposal of this equipment.

Do not return the water softener to store.

If you have any questions, or there are missing parts or damage, please call Toll Free 1-866-986-3223, Monday - Friday, 8 am - 7 pm EST, or visit www.ecodynewatertreatment.com

When you call, please be prepared to provide the model, date code and serial number, found on the rating decal, typically located on the rim below the salt lid hinges.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Model WHES48 Water Softener Warranty Model WHES48 Specifications & Dimensions Salt Storage Capacity 200 lbsWater Softener Safety Your safety and the safety of others are very importantInspect Shipment Water Conditioning InformationIron SedimentInstallation Requirements Proper Order to Install Water Treatment EquipmentLocation Requirements Plumbing CodesValve Drain Requirements Inlet / Outlet Plumbing OptionsInstallation Instructions Typical InstallationTurn OFF Water Supply Install the Brine Tank Overflow ElbowMove the Water Softener Into Place Install Salt Storage Tank Overflow Hose Install Valve Drain HoseComplete Inlet and Outlet Plumbing Sanitize the Water Softener / Sanitize After Service Test for LeaksADD Water and Salt to the Salt Storage Tank Plug in the Water SoftenerSetup Procedure Water Softener SetupTouch Screen Programming Your E-Z Touch Water Softener SET Language SET ContrastRecharge NOW Recharge ButtonSET Recharge Time Schedule a Recharge Setup ButtonSET Time SET Hardness SET Iron LevelRetrieving Information from Water Softener Management System Info Information ButtonSET Clean Feature Customizing Features / OptionsSET Clean Time SET Salt Efficiency SET Salt TypeVolume Units SET UnitsTime Format Hardness UnitsPower Outage Memory Restore Factory SettingsRoutine Maintenance Cleaning the Nozzle & VenturiAdding Salt Breaking a Salt BridgeTroubleshooting Automatic Electronic DiagnosticsOther Initial Diagnostics Checking the TurbineManualadvance Regeneration Check Softener Exploded View Softener Parts List PWAValve Exploded View Valve Parts List

WHES48 specifications

The Whirlpool WHES48 is an advanced water softener designed to provide exceptional water quality for both residential and commercial applications. This model stands out in the market due to its effective water treatment capabilities and user-friendly features.

One of the primary characteristics of the WHES48 is its high capacity, which can handle up to 48,000 grains, making it ideal for large families or homes with significant water usage. This capacity allows for efficient removal of hardness minerals such as calcium and magnesium, which can cause scale buildup in plumbing and appliances. By softening the water, the WHES48 helps to extend the lifespan of faucets, water heaters, and other fixtures, providing significant savings over time.

The WHES48 features a modern demand-initiated regeneration system that optimizes salt and water usage. This technology ensures that regeneration only occurs when necessary, reducing waste and conserving resources. The system monitors water consumption patterns, meaning it regenerates during off-peak hours, further enhancing efficiency.

Another significant advantage of the Whirlpool WHES48 is its user-friendly digital control panel. This intuitive interface allows users to easily program the system for their specific needs and provides a clear display of water usage data, remaining salt levels, and system status. Additionally, the softener is equipped with a bypass valve, allowing homeowners to direct hard water to their taps if ever needed.

Installation is a straightforward process, thanks to the compact design and included installation kit. The WHES48 can fit comfortably in most spaces, making it a versatile option for various home layouts.

The Whirlpool WHES48 also emphasizes low maintenance, with a self-cleaning feature that reduces the need for frequent servicing. It uses food-grade salt, making it safe for households with children and pets.

In summary, the Whirlpool WHES48 is a robust and efficient water softener offering advanced features like high capacity, demand-initiated regeneration, and user-friendly monitoring. Combined with its low maintenance requirements, this model serves as an excellent investment for anyone seeking to improve their home’s water quality and protect their plumbing systems.
Top Page Image Contents