Bacharach 2072-0400 manual Instruction

Page 25

MAC2000

Operation

3.After entering the Charge mode, the following options are available:

•Press the Enter key to accept the 2.00 pound Default.

•Press the Weight Convert key to change the “Set charge weight” units.

•Use the Increase or Decrease keys to set the desired charge amount. Select the next higher value if the exact charge amount cannot be entered. Press Enter to accept the charge amount shown on the screen.

Note: The MAC2000 charges in one-ounce increments, regardless of which unit of measure is selected. This means that sometimes the exact charge amount cannot be entered. For example, the A/C system may require a 1.03 kg charge. The MAC2000 will only allow a setting of 1.02 kg or 1.04 kg. In this instance, always select the next higher value. This difference is only 0.3 of an ounce, which will not affect the vehicle’s A/C performance.

4.By default the MAC2000 charges liquid refrigerant directly into the high side of the A/C system. A technician, however, may choose to charge into both the high and low side by pressing the Low side ON-OFFfunction key. Pressing this key toggles the low-side option on and off. Important! Charging liquid directly into the low side of the compressor could slug the compressor and cause permanent damage. Check with the compressor manufacture before proceeding.

5.The screen should now show the amount of refrigerant set for charging. Press the Start key to begin the charging process.

During the charging process, liquid refrigerant is drawn from the unit’s internal storage tank and charged through the high side (and optionally the low side) of the vehicle’s A/C system. The screen will show the progress of this charging process.

Important! Do not disturb or bump the MAC2000 during charging as any jarring movement can affect the charge accuracy.

Note: If an insufficient pressure differential exists between the tank and the system, charging suspends and the MCR2000 goes into a power-charge mode to increase tank pressure to complete the charge. This normally occurs only when the unit has been in a very cold environment prior to use.

6.When charging is complete, the red light and beeper signal that the process is complete. The MAC2000 automatically goes into the Snap-Shot mode, thus allowing a technician to obtain an after- service snap-shot of important operating parameters of the A/C system. Refer to Section 3.2 for details.

Instruction 2072-0400

21

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Instruction Register Your Warranty by Visiting Table of Contents Operating Notes Introduction General Operating Guidelines Glossary of TermsMAC2000 Control Panel Component Location and DescriptionMAC2000 Front View MAC2000 Right-Side View MAC2000 Left-Side View MAC2000 Back View Introduction MAC2000 Using the Function Keys Introduction MAC2000 Initial Set-Up Instructions Initial Set-UpInitial Set-Up MAC2000 Checking Vehicles for Possible Contaminated Systems External Source Tank TestingInitial Set-Up MAC2000 MAC2000 Operational Overview OperationRecovery Vacuum Charge Snapshot Next Tank air Data Change Diagnosing A/C System Operation Using the Snap-Shot ModeSnap-Shot Transmitter Main Capture Reset Recover Menu Print Recovery Mode Vacuum Mode Evacuation Charge Mode Instruction System Flush Mode Oil Flush Instruction Refrigerant Management System Internal Tank Manual Refill Identify Refrigerant System Set UpCheck Internal Tank for Air Operation MAC2000 Changing the Filter Drier MaintenanceReplacing the External Source Tank Replacing the Printer Paper Replacing the Refrigerant Identifier Filter Parts Parts and ServiceCalifornia Canada Service CentersPage World Headquarters Hunt Valley Circle, New Kensington, PA

2072-0400 specifications

Bacharach 2072-0400 is a state-of-the-art combustion analyzer that stands out in the field of HVAC and building performance testing. Designed primarily for technicians and professionals, this innovative device is equipped with advanced sensing technologies that enable accurate measurement of multiple combustion parameters, ensuring that heating systems operate efficiently and safely.

One of the main features of the Bacharach 2072-0400 is its ability to measure combustion gases, including carbon monoxide, carbon dioxide, oxygen levels, and flue gas temperature. This capability allows technicians to conduct thorough analyses of heating systems, ensuring that they are not only efficient but also compliant with safety standards. By providing real-time data, the device assists technicians in identifying potential issues before they escalate, ultimately contributing to improved system longevity and reduced emissions.

Another highlight of the Bacharach 2072-0400 is its user-friendly design. The device boasts a clear, backlit LCD screen that presents data in an easy-to-read format. Intuitive navigation through its menus ensures that users can quickly access various functions without extensive training. Additionally, the compact and lightweight design of the analyzer makes it convenient for on-site use in a variety of environments.

In terms of technology, the Bacharach 2072-0400 incorporates state-of-the-art sensors that enhance measurement accuracy and reliability. The device utilizes infrared technology for measuring carbon dioxide and temperature, while electrochemical sensors are employed for carbon monoxide detection. These technologies collectively ensure that users receive precise readings, contributing to more informed decision-making during system evaluations.

Furthermore, the Bacharach 2072-0400 includes features such as data logging capabilities, which allow users to store and retrieve measurements for later analysis. This functionality is particularly beneficial for contractors needing to document system performance or for those who must comply with regulatory requirements.

The analyzer also supports easy connectivity options, enabling users to transfer data to laptops or mobile devices for further analysis or reporting. This level of connectivity ensures that the results can be easily communicated to clients or stakeholders, enhancing the professional image of technicians using the device.

Overall, the Bacharach 2072-0400 is an indispensable tool for modern HVAC professionals. With its comprehensive measurement capabilities, advanced sensor technology, user-friendly interface, and data management features, the device sets a new standard in combustion analysis. As energy efficiency and environmental impact become increasingly important, the Bacharach 2072-0400 provides the essential insights needed to optimize combustion systems effectively.
Top Page Image Contents