Bosch Appliances DVA-12T installation manual Power Supply Units, Cooling Modules

Page 13

RAID Subsystem DVA-12T Installation ManualIntroduction en 13

 

ies to their full capacity. It normally requires approximately twelve (12) hours for the battery

 

to be fully charged. If the battery is not fully charged after twelve (12) hours, there is a prob-

 

lem with the BBU module and you should contact your subsystem vendor immediately. While

 

the battery is being charged, the LED on the BBU rear panel and the sixth LED on the rear

 

panel of the controller module will flash. (See Section 4.2.5 BBU Module LED and

 

Section 4.2.6 PSU LEDsfor details on the LED indicators.)

 

You can check the status of the battery’s charge via RAIDWatch or the firmware utility screen.

2.3.7

Power Supply Units

i

The RAID subsystem is equipped with two (2) redundant, hot-swappable, 350W PSUs, which are accessed through the rear of the enclosure. The PSU is permanently mounted into a 2U (dual-level) bracket especially designed to house both the PSU and a cooling module, which is mounted in the lower part of the 2U bracket.

NOTICE!

Hot-swapping the PSU also removes the cooling module at the lower slot.

As shown in Figure 2.11, each PSU comes with a single power socket for power cord plug-in, and a power switch on the right to turn the subsystem on and off. Two (2) embedded cooling fans provide sufficient airflow to keep the PSU cool. A single LED indicates the PSU status.

When any power supply failure occurs, such as over-voltage or fan failure, the LED shines red. A handle at the back of the PSU has been especially designed to enable you to remove the PSU from the subsystem while the subsystem is online. This should only be done if the PSU has failed and needs to be replaced.

A retention screw at the top of the PSU module secures the PSU to the enclosure. To remove the PSU, the retention screw must be removed first. When installing a new PSU module, make sure that the retention screw has been firmly secured.

 

Fig. 2.11 PSU Module

 

For the PSU specifications, please refer to Section 8 Spare Parts and Accessories.

2.3.8

Cooling Modules

 

The two subsystem models are all equipped with three (3) 1U, single-fan, hot-swappable cool-

ing modules. They are installed in the cooling module slots located underneath the controller module and PSU modules (see Figure 2.12.) The cooling fans operate at two (2) fan speed lev- els. When the subsystem is running in normal ambient temperature, the fans operate at the lower speed. When the upper temperature threshold is exceeded, the fans automatically raise

Bosch Security Systems

F.01U.027.798 V1 2006.06

Image 13
Contents RAID Subsystem DVA-12T Page Table of Contents 01U.027.798 V1 Bosch Security Systems Precautions and Instructions Safety PrecautionsESD Precautions 3Certification01U.027.798 V1 Bosch Security Systems Product Overview IntroductionISCSI Host Ports Chassis Overview Enclosure Chassis3Hard Drive Numbering 2Front Panel OverviewRear Panel Overview Backplane Board Subsystem ComponentsFront Handles RAID Controller Module Drive TraysDimm Module 4Controller Module Interfaces6BBU Cooling Modules Power Supply Units4Audible Alarms LED IndicatorsSubsystem Monitoring I2C busHot-swap Capabilities Hot-swappable ComponentsComponents Normalized AirflowInstallation Prerequisites Hardware InstallationPrecautions and Instructions IntroductionStatic-free Installation General Installation Procedure7Drive Tray Installation Rack/Cabinet InstallationInstallation Procedure Flowchart Installation Procedure DoneFront View of an Individual Drive Tray Drive Tray Key-lock Rotation Subsystem Monitoring Overview Subsystem MonitoringBrief Overview of the LEDs Status-indicating LEDsDrive Tray LEDs Ethernet Port LEDs 3Controller Module LEDsName Color Status PSU LEDs BBU Module LEDDefault Threshold Values Audible Alarm7Cooling Module LEDs Failed Devices 4I2C MonitoringSubsystem Connection and Operation Channel Default Settings Model Host Channels Drive Channels1Cabling Host Connection TopologiesDirect-Attached, Single Connection 2Connection through an Ethernet Switches Power On Procedure Power OnPower On Enclosure Check List4Power On Status Check 4Power Off ProcedureMaintenance Subsystem Maintenance and UpgradingGeneral Notes on Component Replacement OverviewReplacing Controller Module Components Controller Module Maintenance OverviewRemoving the Controller Module Replacing the Controller Module 3DIMM Module Replacement1DIMM Module Considerations Push Back the Module Clips on the Sides of the Dimm Module Dimm Module Replacement ProcedureBBU Warnings and Precautions Replacing a Faulty BBU Module2Procedure PSU Module Overview Replacing a Failed PSU ModuleReplacing the PSU Module PSU Parts Identification Cooling Module Overview Cooling Module Maintenance2Replacing a Cooling Module 7Replacing a Failed Hard Drive Hard Drive Maintenance Overview11 Front View of an Individual Drive Tray Replacing a Hard DriveInstall the new hard drive Technical Specifications SpecificationsSpecification Controller SpecificationsPower Supply Specifications Drive Tray SpecificationsCooling Module Specifications 6RAID ManagementNPC Fault Tolerance ManagementAccessories Spare Parts and AccessoriesSpare Parts Model Name DescriptionCOM1 Cable DB9 and Audio Jack Pin Outs Pin OutsEthernet Port Pin Outs CN1 Pin Number Pin NamePin Pin Name Main PowerPage Numerics IndexLAN XOR Page Page Bosch Security Systems

DVA-12T specifications

The Bosch Appliances DVA-12T is a standout in the field of kitchen ventilation, offering a seamless blend of high performance, modern design, and innovative technology. This under-cabinet range hood is engineered to deliver top-notch airflow while maintaining a surprisingly quiet operation, making it an ideal choice for both professional and home chefs.

One of the primary features of the DVA-12T is its powerful ventilation system, which boasts an impressive airflow capacity of 400 CFM. This ensures that even the most intense cooking sessions are met with adequate ventilation, effectively removing smoke, odors, and grease from the kitchen environment. The appliance is equipped with a three-speed fan that allows users to choose the appropriate level of airflow based on cooking needs, from simmering to high-heat sautéing.

In terms of design, the Bosch DVA-12T exemplifies contemporary aesthetics with its sleek stainless steel finish, which not only enhances the kitchen's appearance but is also easy to clean. Its low-profile design allows it to fit neatly under cabinets, making it a space-saving solution that does not compromise on power or effectiveness.

The DVA-12T is fitted with an advanced lighting system that includes LED lights, providing bright and efficient illumination over the cooking area. These lights enhance visibility while cooking and contribute to energy savings compared to traditional incandescent lights.

Moreover, the DVA-12T features a dishwasher-safe baffle filter that efficiently captures grease and enhances the longevity of the appliance. This user-friendly feature simplifies maintenance, allowing consumers to keep their range hood functioning optimally without hassle.

One notable characteristic of the Bosch DVA-12T is its quiet operation. With noise levels that remain as low as 46 decibels, this range hood ensures that you can enjoy conversations and the ambiance of your kitchen while cooking. This is achieved through advanced engineering that minimizes turbulence and promotes smooth airflow.

In conclusion, the Bosch Appliances DVA-12T stands out for its powerful ventilation, stylish design, user-friendly features, and quiet operation. It's an ideal choice for anyone looking to enhance their culinary environment while maintaining a serene atmosphere in the kitchen. Whether for everyday cooking or gourmet meals, this range hood represents the essence of Bosch's commitment to quality and innovation.