Speco Technologies HTINT650S, HTINT650W manual Camera function setting

HTINT650S, HTINT650W

2.Camera function setting

Page 1

	Function		Select			Sub
	setting							Summary
			menu		menu
	menu
				BRIGHT			Adjust the brightness of the screen
				NESS,			(Range : 1~70, Default : 25)
		DC IRIS		IRIS			Adjust the Iris speed of the DC lens
ADJUST				SPEED,			(Range : 1~50, Default : 3)
				FOCUS			Focus addition : To adjust the lens
LENS
				ADD.			focus correctly
		MANUAL		BRIGHT			Manual mode is not recommended
				NESS			using built-in the DC Lens(Default :
							25)
		BRIGHT-					Brightness ADJ. : Adjust the bright-
							ness of the screen when using the
		NESS
							DC lens(Range : 1~70, Default : 25)
		E-		MANUAL			Auto setting is not selectable
						FLK,
		SHUTTER		- - -			when selected DC Lens
							OFF : Deactivates function
							LOW : Auto selection between
		AUTO			OFF,		5.3dB and 32dB
					LOW,		HIGH : Auto selection between
EX-		GAIN
					HIGH		5.3dB and 37dB(You can not
POSURE
							use the DIS, Day&Night when
							AGC is off)
		SENS-		OFF,			OFF : Deactivates function
							AUTO : Using sense up when it is
		UP		AUTO
							low luminance(x2~x512 selectable)
		RETURN					Save the value then move back
							to previous menu
		*Notes : If		the AGC is off, the sense-up function is not
		available. As the sense-up level increases, an after-
		image will appear.
		ATW					Color temperature 1,700~11,000°K
		OUT-					Color temperature 1,700~11,000°K
		DOOR
COLOR		INDOOR					Color temperature 4,500~8,500°K
		MANUA					Adjust the Red or Blue values to
TEMP
		L					shift the color of the screen
		AWC →					Find the optimal white balance for
							current luminance environment
		SET					(The camera focus must towards
							to white paper)
WDR		OFF					Deactivates function
							Wide dynamic range function(1
SET		ON
							~15 level selec-table, Default : 8)
		OFF					Deactivates function
				LEVEL,
				TOP,			User programmable SLC zone
		SLC		BOTTOM,			and compensation level
				LEFT,
				RIGHT
				LEVEL,
SLC SET				LIMIT,
				MASK
				COLOR,			Removed HIGH LIGHT, It enable
		HLC		MASK
				TONE,			us to watch license plate clearly
				TOP,
				BOTTO
				M, LEFT,
				RIGHT
							Reduce noise in low illumination
SPECO		ON		Level			(Reduction level is selectable,
							Default : 20)
DNR		OFF					Deactivates function
		*Notes : If the AGC is off, the DNR function is not available
				BURST
				MODE
				COLOR			Day : Color↔Night : B/W
		AUTO		→ B/W,			(Switching time & speed adjust-
				B/W →			able)
				COLOR,
DAY &				RETURN
		EXT					Change the color↔B/W by ex-
NIGHT
							ternal signal (Not available)
		COLOR					Fixed at color(LED OFF)
				BURST
		B/W		MODE			Fixed at B/W(LED ON)
				(OFF/ON),
				RETURN
		*Notes : If the AGC is off, this function is unavailable
Page 2							Please refer to "Page 2"
		SAVE					Save the value and exit menu
EXIT		NOT					Exit the main menu without save
		SAVE
		DE-					Reset the camera setup value
		FAULTS					to the factory default

					Page 2
	Special		Select		Sub
	setting						Summary
			menu		menu
	menu
		V-REV				Set a vertical image inversion
		H-REV				Set a horizontal image inversion
		DIGI-				Max 16x digital zoom available
		ZOOM				(Default : X1.0)
		FONT				Change the color of OSD
ADJUST		COLOR				(Default : Blue, 5 color is available)
						The image outline will be strong
		CLARITY				and clear according to sharpness
						level increasing(Default : 13)
						If this function is Off, it may looks
						like un-focused
		RETURN				Save the value then move back
						to previous menu
				GAMMA,
				PED
				LEVEL,
		LCD		COLOR
				GAIN,
				DEFAULT
				SET
				GAMMA,
MONI-				PED		You can change the settings value of
				LEVEL,
TOR		USER		COLOR		video appropriate to your monitor
				GAIN,
				DEFAULT
				SET
				PED
				LEVEL,
		CRT		COLOR
				GAIN,
				DEFAULT
				SET
CAM		OFF				No title displays on the screen
						Display the camera's title on the
TITLE		ON				screen(Max. 15character, position
						adjustable)
SYNC		INT				Internal Sync with 12V DC power
						Setting the phase is selectable when
TYPE		LL
						used 24VAC(Dual power only)
		SENSITI		AREA1~		When sensitivity number is high,
		VITY		AREA8		also motion detection sensitivity
						will increase
		AREA		OFF, ON		Determines whether to use the MD
		MODE				area selected in SENSITIVITY
				L_TOP,
				R_TOP,		Determines which of the 4 vertices
		SEL		L_BOT-
		POS		TOM,		of each MD area is to be used
				R_BOT-
V				TOM
		XPOS				Determines the coordinate of the
MOTION						horizontal axis for SEL POS
		YPOS				Determines the coordinate of the
						vertical axis for SEL POS
						Fill the color in selected area(The
		FILL →				color of filling is sequentially se-
						lected as brown, orange, blue,
		SET
						cyan, yellowish green, yellow, ma-
						genta and red.)
		RETURN				Save the value then move back
						to previous menu
		*Notes :		If the camera detected motion, "MOTION
		DETECTED" will appear on the screen
		AREA		AREA1~
		SEL		AREA12
		AREA		ON, OFF
		MODE
				GREEN,
				RED,
		MASK		BLUE,
		COLOR		BLACK,		Make a zone for your privacy
				WHITE,		You can select privacy zone up
PRIVACY				GRAY		to 12 area
		MASK		1~10
		TONE
		TOP
		BOTTOM
		LEFT
		RIGHT
		RETURN				Save the value then move back
						to previous menu
STABI			ON,				This function can be mitigates
							image movement from external
-LIZE			OFF
							factors
LAN-						Select language
GUAGE
PAGE 1						Select this to save the special menu
						settings and return to the main menu

ㆍThe "" icon appeared with desired function, press the set button to move sub menu.

ㆍThe "---" icon appeared with function that is una-vailable according to function setting.

Speco Technologies is constantly developing product improvements. We reserve the right to modify product design and specifications without notice and without incurring any obligation.

Rev. 7/7/10.

3B15011B