Linear AE1000Plus Internal Controls, On-board Pushbuttons, On-board Display

Page 19

Internal Controls

On-board Pushbuttons

Seven pushbuttons are on the main circuit board. Refer to the fi gure for the location of each pushbutton.

UP button adds one to the value on the STATUS/PROGRAM display.

DOWN button subtracts one from value on the STATUS/PROGRAM display. Press with the UP button for one second to enter Programming Mode.

ENTER button accepts the value on the STATUS/PROGRAM display during programming, clears an indication during the supervisory display.

RELAY “A” LATCH press to latch relay “A”, press again to unlatch.

RELAY “B” LATCH press to latch relay “B”, press again to unlatch.

RELAY “C” LATCH press to latch relay “C”, press again to unlatch.

RELAY “D” LATCH press to latch relay “D”, press again to unlatch.

On-board Display

The STATUS/PROGRAM display shows the current system conditions and is used for system setup.

Power-up

When power is applied, the display will show the current mode of operation (AXNET “An” or AccessBase2000 “Ab”) and the version number of the

rmware installed. The default mode of operation is AccessBase2000.

Program Mode

Program Mode uses the display and the UP, DOWN, and ENTER pushbuttons. The setting the network node address, operation mode, and clearing the memory can be performed in Program Mode.

Refer to the following steps to change the system settings:

1.To enter Program Mode, press and hold the UP and DOWN pushbuttons together for one second. While in Program Mode, both decimal points on the display are lit.

2.The display shows the current network node number setting.

3.Press the UP or DOWN button to cycle the display through the options that can be selected (see Program Mode Display Table).

4.When the desired option is displayed, press the ENTER button to select the option.

NOTE: In network installations, a unique network address (1-8 for AccessBase2000, 1-4 for AXNET) must be set before communicating with network.

NOTE: If using AXNET for programming the system, select the An programming option, for AccessBase2000 select Ab.

After the option is selected, the system will restart.

Status Mode

While the system is running, the display will show the current system status. Normally the left digit will show a moving pattern and the right digit will show the unit’s Network Node number.

When a supervisory condition exists, the display will cycle to show the condition(s). When an item is displayed, press the ENTER button to clear the display (clears the display only, the condition may still exist). Refer to the following table for the supervisory condition display codes.

 

STATUS MODE DISPLAY

DISPLAY

CONDITION

01

MGT TRANSMITTER STATUS EXCEPTION

02

MGT TRANSMITTER LOW BATTERY

03

MGT TRANSMITTER TAMPER

04

AC POWER FAIL (BACKUP BATTERY REQUIRED)

05

CHANNEL “A” LOCKED CLOSED

06

CHANNEL “B” LOCKED CLOSED

07

CHANNEL “C” LOCKED CLOSED

08

CHANNEL “D” LOCKED CLOSED

09

MODEM FAILURE

STATUS/PROGRAM

"UP"

 

DISPLAY

 

BUTTON

"DOWN"

 

 

 

 

 

BUTTON

"ENTER"

 

 

BUTTON

 

 

 

 

RELAY "A"

 

 

LATCH

 

 

RELAY "B"

AE1000PLUS

 

LATCH

MAIN CIRCUIT BOARD

 

 

 

RELAY "C"

 

 

LATCH

 

 

RELAY "D"

 

 

LATCH

STATUS/PROGRAM

 

DISPLAY

 

 

SYSTEM IDLE

 

 

RIGHT DIGIT SHOWS NETWORK NODE ADDRESS

LEFT DIGIT CIRCULATES

PROGRAM MODE

DECIMAL POINTS LIGHT, DIGITS SHOW PROGRAMMING OPTION

STATUS MODE

DIGITS SHOW SUPERVISORY CODE

PROGRAM MODE DISPLAY

AccessBase2000 MODE

AXNET MODE

FUNCTION

 

 

 

0.1.

0.1.

SET UNIT TO NODE #1

 

 

 

0.2.

0.2.

SET UNIT TO NODE #2

 

 

 

0.3.

0.3.

SET UNIT TO NODE #3

 

 

 

0.4.

0.4.

SET UNIT TO NODE #4

 

 

 

0.5.

 

SET UNIT TO NODE #5

 

 

 

0.6.

 

SET UNIT TO NODE #6

 

 

 

0.7.

 

SET UNIT TO NODE #7

 

 

 

0.8.

 

SET UNIT TO NODE #8

 

 

 

A.N.

A.b.

SWITCH OPERATION MODE

 

 

 

B.L.

B.L.

RESERVED (DO NOT USE)

 

 

 

C.L.

C.L.

CLEAR UNIT’S MEMORY

19

Image 19
Contents AE1000Plus Operation ContentsProgramming and Cardholder Maintenance IntroductionFeature Overview Hardware FeaturesSoftware Highlights Wiegand Accessories Accessory Overview Pbus AccessoriesComponent Locations Installation NoteThis Wiring Example Shows Wiring DiagramImportant Mounting Requirements Surface Mounting Entry System MountingMounting Preparation Surface MountingPedestal Mounting Recessed MountingRequest-to-Exit Inputs Relay Output WiringDoor or Pedestrian Gate Control Gate ControlRS-232 Port Power, Battery, & Ground WiringPower Wiring Backup Battery / Uninterruptable Power SupplyOptional Radio Antenna Telephone WiringImportant Telephone Wiring Tips Typical Telephone WiringCamera Installation Postal Lock InstallationOptional Postal Lock Wiegand Terminals Pbus AccessoriesWiegand Accessories Route cable from the AE1000Plus to the accessoryNetwork Configurations for Axnet Programming Optional Network ConnectionOptional Network Connections Network Configuration for AccessBase2000 ProgrammingNetwork Network Wiring with Hub RS-485 Network WiringNetwork Daisy-chain Wiring System Diagnostics System AdjustmentsOn-board Pushbuttons Refer to the following steps to change the system settingsDisplay shows the current network node number setting Internal ControlsAE1000Plus Operation Requesting Access with an Entry CodeRequesting Access with a Wireless Transmitter Requesting Access with a Visitor Call18-3/8 Dimension DrawingSpecifications 16-1/4Troubleshooting FCC Notice Linear Limited WarrantyCopyright 2008 Linear LLC
Related manuals
Manual 12 pages 25.92 Kb

AE1000Plus specifications

The Linear AE1000Plus is a sophisticated access control and security system designed to meet the unique needs of residential and commercial environments. This advanced model is part of Linear’s commitment to providing reliable and efficient security solutions. It offers enhanced features, cutting-edge technologies, and exceptional characteristics that set it apart in the market.

One of the standout features of the AE1000Plus is its versatility in handling various access control modes. It supports access via key fobs, keypads, and biometric scanners, allowing for seamless integration with existing systems. This flexibility ensures that users can select the most appropriate method for their security requirements, enhancing convenience without compromising safety.

The AE1000Plus incorporates advanced wireless technology that facilitates easier installation and use. This wireless capability eliminates the need for extensive wiring, significantly reducing installation time and costs. Additionally, the system can communicate with Linear's extensive range of peripherals, including security cameras and alarm systems, providing a comprehensive security solution.

Another notable characteristic is its robust capacity for managing multiple users. The AE1000Plus can store a substantial number of user codes and fobs, making it ideal for larger facilities or properties with frequent visitor access. This feature empowers administrators with control over who can access specific areas while maintaining an audit trail of entries and exits.

The system is built with a user-friendly interface, ensuring ease of operation for both administrators and users. Programming and configuration can be streamlined through intuitive menus, while easily accessible manuals provide guidance for troubleshooting and adjustments. User experience is further enhanced by the AE1000Plus's compatibility with mobile applications, able to manage access remotely.

Security is paramount, and the AE1000Plus excels in implementing high-security standards. It employs encryption protocols that protect transmitted data from unauthorized access, ensuring the integrity and confidentiality of user information. The system is also designed to perform reliably in various environmental conditions, making it suitable for outdoor applications.

In summary, the Linear AE1000Plus combines versatility, advanced technology, and user-oriented design to create a leading access control solution. Its array of features ensures robust security while offering the flexibility to meet the demands of various settings, confirming Linear's position as a trusted name in the security industry. Whether for residential or commercial use, the AE1000Plus stands out as a reliable choice for modern security needs.