Guardian Technologies DFT 150/175, DVST manual Country specific settings

Page 37

DVST Installation Guide

Modems

7.8MOTOROLA VFAST

Cable required to connect to DVST: (25 to 25 - V24 SYNC)

When installing the VFAST MODEM the following procedure should be followed:

Connect the MODEM and DVST as in the installation chapter.

Power up the DVST (leave the MODEM without power).

Enter the setup mode and configure the DVST for operation with the VFAST MODEM by typing the command MODEM=ATMODE,MODSTR=FAST (default setting).

Power up the MODEM and wait for the self test to finish.

Type SEND then <ENTER>.

The DVST will program the MODEM.

It is good practice to store these values permanently in the MODEM.

Then the values will not be lost if power is removed from the MODEM.

To store these values proceed as follows:

User= AT&Y1&W1 <return>

Send <return>

Moden displays <save completed>

The MODEM will then always power up with the correct operational configuration.

Country specific settings

The answer on number of rings command *AA1 is not valid in some countries (France, xx) and the MINIT string should be reprogrammed with the value *AA2.

The MINIT string is programmed as:

MINIT=AT&M1 &D2 &C1 *FLO *OC1 *DTO *DE12 *AA1

Dedicated Micros Ltd

Page 25

Image 37
Contents Page Page DFT-0150 Installation GuidePage Safety Page FCC and DOC Information Regulatory NotesA. and Canadian Models Only CE MarkPage Table of Contents Modems Demonstration ModeLeased Line Transmission Terminal AdaptersCalls Images and TransmissionGlossary Returns Procedure Alarms & EventsAudio Cable Assemblies1Introduction Event monitoring AlarmsDFT-0150 Transmitter TelemetryPage Items in packing Unpacking the unitPacking the Dvst Page 3Operation Alarms FeatureCallback Offline Frozen Alarm Freeze All AlarmsTrack Last Alarm No Frozen ImagesRear Panel connections 4Installation37 Way Alarm Connections Power InputsSetup using a PC 5SetupWhat you require Dvst Commands Remote SetupAuxiliary Port Define Camera InputsDefine Auxiliary Ports 1,2 Default settings AUX1 N 38400Set Port usage Each field entry is separated by a space. If AUX2 N 38400Demonstration mode Demonstration ModeTech Note Demo CableSingle cable operation Connecting the demo cablePage 7Modems Modem CommandsPstn Connection Modem Modem MBAUD= Set Modem port Async baud rate. default 9600, 19200MODSTR= Set type of modem Fast or Sync default, Fast Modem configuration stringsZyxel US Modems Only USER=... Available for user configuration Default, blankModem Operation Default, AtdtModem dial string Configuration of modem in direct mode Connecting a modem in direct modeCall request Call answer requestGeneral settings for modems in Atmode Using a modem in AtmodeModem Requirements Action required of Modem Possible AT settingsAll modems Synchronous ModemsMINIT=AT&M1 &D2 &C1 *FLO *OC1 *DTO *DE12 *AA1 Country specific settingsTransmission speed No DialtoneUser=ATX3*BDO&Y1&W1 Where AT*MXnDIP Switch Settings Synchronous Operation Syncronous modeMicrocom Trailblazer Async modeSend RET Octocom OSI 8196AModem RET Modems Dvst Installation Guide This page intentionally blank Terminal Adapters Default, onIsdn Connection Terminal Adapter Sets dual Isdn support on or OFFConfiguring a Terminal Adapter for direct mode operation Connecting a terminal adapter in direct modeMaking a Call Answering a CallDirect Connection Gandalf TA1Step Instruction Ascom 5000 / CitamRemarks ISDN0 RET Atret AT&WRET, ESC ISDN1RET Atret ISDN=ATMODE RET DUALISDN=ON RET Isdnstr = Citam RETAT&WRET ESC Quit RET X21Step Instruction Remarks ‘CONF’‘CHNG’ ‘DIPS’ISDN=ATMODE RET Dataflex TAQuit RET LEASED= Leased line operation, options are default, OFF Dvst set up for leased line operationLeased Line Transmission Leased line terminologyLeased line operation SET UP RX or Slave END SET UP TX or Master ENDAscom 64000 Baseband Modem Page PASSWORD= Set system password to PasswordsSet telephone entry n password to 10CallsOn Screen Titling Default, blank Telephone Number Entries / Connection CommandsSet telephone entry n to FormatDefault, 60 seconds Call connection timeout periodDefault, 30 seconds CALLBACK= Set call back on or OFF Default, offImages and Transmission CAMLO=Sets low resolution cameo operationImage size Target Picture SizesPage Alarm Connections Alarms & EventsAlarm Settings Purpose & intended useSet contact nn normally open Images transmitted on alarmSet contact nn normally closed Default is Auto Set alarm outputs Auto / ManualALMODE= ...Set Alarm operation mode Alarms & Events Dvst Installation Guide Equipment required but not supplied 13AudioConnecting the DAL100 Cable Assemblies 14.1 X21 to V35 Cable Assembly 14.2 X21 Cable Assembly 14.3 V24 Sync Modem Cable Assembly 14.4 RS232 Cable Assembly DVST-PC 14.5 RS232 Cable Assembly DVST-DAL Isdn 15GlossaryPage Event of Difficulty Returns ProcedurePage Dvst Installation Guide Returns Procedure Returns Procedure Dvst Installation Guide

DVST, DFT 150/175 specifications

Guardian Technologies has made significant strides in the air purification industry with its innovative DFT 150 and DFT 175 models, designed to enhance indoor air quality for both residential and commercial spaces. These advanced devices leverage cutting-edge technology to deliver clean, fresh air, addressing the increasing need for effective air purification solutions.

One of the standout features of the DFT series is its multi-stage filtration system. Both the DFT 150 and DFT 175 are equipped with a pre-filter that captures large particles, such as dust and hair, followed by a true HEPA filter. This HEPA filter is capable of capturing 99.97% of airborne pollutants as small as 0.3 microns, including allergens, mold spores, and pet dander. This is an essential feature for individuals suffering from allergies or respiratory issues, ensuring that the air they breathe is significantly cleaner.

In addition to the HEPA filtration, Guardian Technologies has incorporated a UV-C light that works in tandem with the filter system. This technology helps to kill airborne bacteria and viruses, providing an extra layer of protection against pathogens, which is particularly crucial in today’s health-conscious environment.

Another characteristic that sets the DFT 150 and 175 apart is their energy efficiency. Both models are designed to operate quietly and consume minimal energy, making them suitable for continuous use in bedrooms, living rooms, or offices without causing a spike in electricity bills. The DFT 175 model features an added air quality sensor, which monitors and adjusts the fan speed automatically based on the detected air quality, ensuring optimal performance without unnecessary energy expenditure.

The sleek, modern design of the DFT series ensures they blend seamlessly into any decor. With portable options, users can easily move these units from one room to another, providing flexibility in air purification.

Moreover, the DFT models come equipped with easy-to-replace filter indicators, notifying users when it’s time to replace the filters. This convenience promotes consistent air quality management without the hassle of manual reminders.

In conclusion, Guardian Technologies' DFT 150 and DFT 175 models represent an excellent investment for anyone looking to improve indoor air quality. Their sophisticated filtration technology, additional UV-C features, energy efficiency, and user-friendly design make them a top choice for air purifiers in the market today.