Installation Instru ti6hs ontd, Venting contd

Installation Instru ti6hs ( ont'd)

Venting (cont'd)

All vent gases must be completely vented to the outdoors of the structure (dwelling). Installonly the draft hood provided with the new water heater and no other drafthood.

Ven_ pipes must be secured at each ioint with sheet metal screws,

CHIMNEY

RISE PER LINEAR

FOOT

VENT PIPE INSTALLATION

There must be a minimum of 6" clearance between single wall vent pipe and any combustible material. Fill and seal any clear-

ance between single wall vent pipe and combustible material with mortar mix, cement, or other noncombustible substance.

Fot other than single wall, follow vent pipe manufacturer's clear- ance specifications. To insure a tight fit of the vent pipe in a brick chimney, seal around the vent pipe with mortar mix cement.

I	. A WARNING		J
	Failureto have reqmred _	between vent pipingand
	combustiblematerialwill resultin a flr_ hazard,		I

A WARNINGI I Besurevantplpob properlyconnectod pr_mt escapeofI [ den_rous _ gesoswitch €ouldcamedeadtyasphyxiatio_

Gas

AWARNING

take sure the gas suppliedis the same type listed on the nodel rating plate. The inlet gaspeessummust not exceed

0.5in.water column(2.61dPa)for natural gasor 13 in.wa_er column (3.2kPa) for propane (L.R) ga_ The minimum inlet gas pressurelistedon the model radng plate isfor the pur- poseof input

AWARNING

[ ff the gascontrol valveissol.-tedto pressuresexceeding 'AI I poundper squareinch(3.SkPa),the damageto the gascon-J

I trel valve €°uld result in a tire oc _

ion fr°m leak_g ges" J

I. A WARNING

If the main gashne shutoffserving.ai.gasappliancesIis used, aisotorn "OFF" the ps at eachapld*anceLeme. all gesappli-

ancesshut off untilthe water heater installationiscomplete.

A gas line of sufficient size must be run to the water heater. Consult the latest edition of National Fuel Gas Code ANSI

Z223.1, also referred to as NFPA 54 and the gas company con- cerning pipe size.

There must be:

•A readilyaccessible manual shut off valve in the gas supply line serving the water heater, and

•A drip leg (sediment trap) ahead of the gas control valve to help,

prevent dirt and foreign materials from enteting the gas enntroi valve.

•A flexible gas connector or a ground joint union between the shutoffvalve and control valve to permit servicing of the unit.

A WARNING

Be sure to check all the gas piping for leaks before lighting the water heater. Use a soapy water solution, not a march or open throe. Rinse offsoapy solution and wipe dry.

Chemical vapor corrosionof the flue and vent system may occurif air for combustioncontainscertain chemicalvapors.

Spray .canpropellantg cleaningsolvents, refrigerator and air

conditioner refrigerants,swimming pool chemicals,.calcium and sodiumchloride,waxes,bleach,and processthem,cals are

typical compoundswhichare potentiallycorrosive.

Standard Models are for installation up to 3,300 feet above sea level.

fI-_h Altitude Models are for installation from 3,300 to 5,500

tabove sea level.

Ifa standard model is installed above 3,300 feet or a high altitude model is installed above 5,500 feet, the input taring must he reduced at the rate of 4 percent for each 1,000 feet above sea level.

Contact your local Sears Service Center or gas utility for further information.

The appliance and its gasconnection must be leak tested

AWARNINGI

beforeplacingthe appliance in operation.

153.3304OI, 153.330551, 153.330451, 153.330751, 153.330701 specifications

The Kenmore 153 series of dehumidifiers, including models 153.330501, 153.330701, 153.330451, 153.330751, and 153.330551, represent a versatile lineup designed to tackle moisture control in residential spaces. These dehumidifiers are essential appliances for maintaining optimal humidity levels, which can contribute to improved air quality and comfort in homes, especially in areas prone to dampness.

One of the main features of the Kenmore 153 series is their considerable moisture removal capacity. These models are engineered to effectively extract moisture from the air, with capacities ranging from 30 to 70 pints per day, allowing them to handle spaces of various sizes from small rooms to larger basements. This makes them ideal for both typical home environments and more humid settings.

Technologically, the Kenmore 153 series includes advanced humidistats that allow for precise humidity control. This feature enables users to set their desired humidity levels, ensuring that the dehumidifier operates only when necessary, helping to save on energy costs. The series also includes built-in continuous drainage options, which can be a convenient solution for prolonged use, eliminating the need to frequently empty the water tank.

Another noteworthy characteristic is their user-friendly interface. Most models in this series feature digital displays for easy monitoring, along with simple controls that make adjusting settings straightforward. This focus on usability is complemented by quiet operation, ensuring that the dehumidifiers can run unobtrusively in the background without causing significant noise disruption.

Energy efficiency is a crucial aspect of the Kenmore 153 line, as the models are designed to meet Energy Star standards. This means they consume less energy while delivering effective performance, making them an environmentally friendly choice in moisture management.

Additionally, these models often come equipped with features such as washable filters that help to reduce airborne allergens and ensure cleaner air. This is particularly beneficial for individuals with allergies or respiratory issues, creating a healthier indoor environment.

In summary, the Kenmore 153.330501, 153.330701, 153.330451, 153.330751, and 153.330551 dehumidifiers combine powerful moisture removal capabilities with advanced technologies, user-friendly features, and energy efficiency. They are a valuable investment for any homeowner looking to improve air quality and combat humidity-related issues effectively.