Kenmore 153.337072, 153.337002 Leakage Checkpoints, Primary anode rod fitting may be leaking

Page 26

Troubleshooting Guide (cont'd)

Leakage Checkpoints

Use this guide to check a "Leaking" water heater. Many suspect-

ed "Leakets" are not leaking tanks. Often the source of the water can be found and corrected.

lfyou are not thoroughly familiar with your local gas codes your

water heater, and safety practices, contact the Sears Service to check the water heater.

ACAUTION--_

Read this manual first. Then before checking the water I heater make sure the gas supply has been turned I "OFF", and never turn the gas "ON" before the tank is I

completely fu of water.

A CAUTION

I

Never use this water heater unless it is completely filled I with water. To prevent damage to the tank, the tank must be filled with water. Water must flow from the hot I water faucet before turning "ON" gas to the water

heater.

Water at the draft hood is water vapor which has con- densed out of the combustion products. This is caused by a

problem in the vent. Contact the Sears Service Center,

*Condensation may be seen on pipes in humid weather or pipe connections may be leaking.

*The primary anode rod fitting may be leaking.

Small amounts of water from temperature-pressure relief valve may be due to thermal expansion or high water pres-

sure in your area.

0

o

®

®

*The temperature-pressure relief valve may be leaking at the tank fitting.

Water from a drain valve may be due to the valve opened

slightly.

*The drain valve may be leaking at the tank fitting.

Combustion products contain water vapor which can con- dense on the cooler surfaces of the tank. Droplets form and drip into the fire or run on the floor. This is common at

the time of startup after installation and when incoming water is cold.

®Water in the water heater bottom or on the floor may be

from condensation, loose connections, or the relief valve. DO NOT replace the water heater until a full inspection of all possible water sources is made and necessary correc-

tive steps taken. Leakage from other appliances, water lines, or ground seepage should also be checked.

NOTE: To check where threaded portion enters tank, insert cotton swab between jacket opening and fitting. If cotton is wet, follow "Draining" instructions in the "Service and Adjustment" section and then remove fit- ting. Put pipe dope or teflon tape on the threads and

replace. Then follow "Filling the Water Heater" instructions in the "Installation Instructions" section.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents For Your Safety What to do if YOU Smell GASSafety Precautions Serious BodilyAwarning Ifro Contents Specifications Customer ResponsibilitiesMaterials Needed Additional Tools Needed When Sweat SolderingMaterials and Basic Tools Needed Basic ToolsInstallation Instructions Removing the Old Water HeaterAwarning Installation Instructions contdTypical Installation Facts to Consider About Location AcautionVentilation For Appliances Located in Unconfined Spaces Room InstallationCombustion Air Water Piping Temperature-Pressure Relief Valve Relief Valve OpeningVenting Vent Pipe InstallationFilling the Water Heater Inches Venting contdSquare DEATH, Serious Bodily INJUR, or Property DamageGAS Piping with ContdGas Piping contd Model Rating Plate Installation ChecklistBefore Lighting the Pilot Check for Leaks Operating InstructionsLighting Not Force Operating Instructions contdWhattodoif Yousmellgas PilotburnerTemperature Regulation Hotierwatercan SCALDWater heatersare intendedtoBurner Cleaning Service and AdjustmentTank Sediment Cleaning Venting System InspectionDraining Service and Adjustment contdService HousekeepingStrange Sounds Troubleshooting GuideStart Up Conditions Troubleshooting Guide contd Start Up Conditions contdWater is TOO HOT High Temperature Shut OFF SystemNot Enough or no HOT Water Leakage Checkpoints Primary anode rod fitting may be leakingPage Page Page Parts Order List Parts Order List contd Kenmorecommercialgaswater Heaters Model NumbersWarranty

153.337002, 153.337072 specifications

The Kenmore 153.337072 and 153.337002 represent a duo of high-efficiency window air conditioning units that have become popular choices for consumers seeking effective cooling solutions. Engineered with modern technology, these models promise to deliver optimal performance while maintaining energy efficiency.

One of the standout features of the Kenmore 153.337072 is its dual cooling and heating functionality. This versatility allows it to not only cool spaces during the hot summer months but also provide warmth during the chillier seasons. With a cooling capacity of 7,000 BTUs, it is suitable for rooms up to 350 square feet, making it ideal for bedrooms or small living areas. On the other hand, the 153.337002, while also a cooling unit, focuses solely on cooling performance, boasting a similar BTU capacity tailored for energy-efficient cooling.

Both models incorporate advanced energy-saving technologies. They are equipped with Energy Efficiency Ratio (EER) ratings that exceed the minimum standards set by energy regulatory bodies. This means consumers can enjoy a comfortable indoor climate without incurring high electricity bills. With features like programmable timers and sleep modes, users can manage cooling more effectively, adjusting temperature settings to minimize energy consumption.

In terms of user convenience, both units come with user-friendly remote controls, allowing easy adjustments from anywhere in the room. The digital control panel is intuitive, featuring clear LCD displays for monitoring settings. They also include multiple fan speeds and cooling modes to cater to individual preferences, ensuring a personalized experience.

Maintenance is simplified with the inclusion of washable and reusable air filters, which enhance indoor air quality by reducing dust and allergens. A filter replacement indicator alerts users when a cleaning is required, promoting optimal performance and hygiene.

In conclusion, the Kenmore 153.337072 and 153.337002 embody a blend of efficiency, user convenience, and advanced cooling technology. Whether you are looking for a unit that provides both heating and cooling or one focused solely on cooling, these models offer reliable solutions to keep indoor spaces comfortable year-round. Their commitment to energy efficiency not only benefits consumers economically but also aligns with environmentally conscious practices, making them a noteworthy choice in the air conditioning market.
Top Page Image Contents