CONTROL PANEL
4. TEMP-
•Pressing this button in cooling mode decreases the desired room temperature setting by 1°F (1°C) down to a minimum setting of 63°F (17°C).
•Pressing this button in heating mode decreases the desired room temperature setting by 1°F (1°C) down to a minimum setting of 59°F (15°C).
5. LED DISPLAY
The display shows the current temperature setting.
By pressing the (
) or (
) buttons, the temperature setting can be changed.
When pressing the timer button ( 
), the number of hours is shown until delayed
6. SPEED |
|
|
Pressing this button sets the ventilator fan speed to “ | (low)”, “ | (medium)”, |
“
(high)” or “ 
(automatic)”. When (
) is selected:
•If the set temperature is more than 16.2° F ( 9° C) different than room temperature, the fan will run at full speed.
•If the set temperature is less than 9° F (4° C) different than room temperature, the fan will run at medium speed.
•When the set temperature is reached, the fan will run at low speed. When the temperature becomes more than 9° F (4°C) different than room temperature, the fan will change to medium speed.
7. TIMER
Programmable timer button for delayed
How to program a delayed start-up
This function is used to set the number of hours delay before the appliance comes on. Proceed as follows:
•With the power ON, select the desired Mode of operation (Cool, Heat or Dehumidify)
•Turn the power OFF.
•Press the TIMER button (“00” will blink in the display). While the display is blinking, use the up and down buttons to set the number of hours delay before the unit begins operation.
•Wait a few seconds for the display to show the set temperature. Use the up and down buttons to adjust the set temperature if desired.
•After the set number of hours has expired, the unit starts automatically.
NOTE: If you press the POWER button before the set delay time has expired, the delay setting will cancel and the unit will immediately turn ON.
12
CONTROL PANEL
How to program a delayed shutdown
This function is used to set the number of hours delay before the appliance shuts off. Proceed as follows:
•With the power ON, select the desired Mode of operation (Cool, Heat or Dehumidify).
•Press the TIMER button (“00” will blink in the display). While the display is blinking, use the up and down buttons to set the desired number of hours until shutdown.
•Wait a few seconds for the display to show the set temperature. Use the up and down buttons to adjust the set temperature if desired.
•After the set number of hours has expired, the unit shuts down automatically.
NOTE: If you press the POWER button before the set shutdown time has expired, the unit will shut down immediately.
8. SLEEP
The Sleep mode is ideal for nighttime operation, as it automatically reduces the fan speed and minimizes the compressor running, for the quietest operation.
While the unit is ON, press the SLEEP mode button. The unit will switch to low fan speed.
In COOLING mode, the temperature setting automatically increases by 2° F (1° C) each hour for the first two hours of operation. As a result, the Sleep function provides most cooling when you first go to bed. The two setting increases while you are sleeping compensate for the typical decrease in ambient temperature as the night progresses. If the ambient temperature becomes 2° F (1° C) cooler than the temperature setting, the compressor will turn off. The compressor turns back on when the ambient temperature becomes 2° F (1° C) warmer than the ambient temperature.
In HEATING mode, the temperature setting is automatically DECREASED like above, and the compressor turns off if the ambient temperature becomes 2° F (1° C) BELOW the setting.
If desired, the fan speed can be manually changed while in SLEEP mode. SLEEP mode cannot be activated while the unit is in DEHUMIDIFY mode.
REMOTE CONTROL
INSERTING BATTERIES - This remote control uses two AAA batteries.
•Remove the back cover of the remote control
•Insert two AAA 1.5V batteries, making sure they are in the correct position (see instructions inside battery compartment).
•Replace the cover.
DO NOT mix old and new batteries. DO NOT mix together Alkaline, Standard
Dispose of batteries properly. DO NOT leave batteries in the remote if it will not be used for longer than 2 months.
13