Roberts Gorden CRV-B-8, CRV-B-6, CRV-B-2, CRV-B-4 Selecting the Burners, Radiant Distribution

Page 16

CRV-SERIES DESIGN MANUAL

EXAMPLE 2:

Given a building with a calculated heat loss of 500,000 Btu/h, what is the installed capac- ity required of a CRV-Series system mounted at 50' (15 m)?

CORAYVAC® Installed Capacity = Heat Loss x Radiant Adjustment x Height Adjustment.

For CORAYVAC® systems, a .80 radiant adjust- ment factor is used.

The height adjustment is 1% per foot over 20' (3% per meter over 6 meters), or 1.30.

∴CORAYVAC® Installed Capacity = 500,000 (Btu/h) x .80 x 1.30 = 520,000 (Btu/h).

Note in Example 2, if equipment had been convention- ally sized based on thermal output only, a nearly iden- tical input requirement would result. For mounting heights above 60' (18 m), no further correction is gen- erally necessary if the floor level radiant intensity is sufficient to establish a reserve capacity (hence, radi- ant comfort), and the heat loss

requirement is satisfied based on thermal output.

Due to the complexity of installations with mounting heights over 60' (18 m), it is advisable to contact Rob- erts-Gordon for further information regarding the spe- cific application.

4.3 Selecting the Burners

The number of burners and input for each must be specified in the design layout. The following factors should be considered when selecting burner input:

•Heat gain and distribution required.

•Mounting height.

•Flow loading restrictions.

•Length of radiant branches.

•Distance required between burners.

•Desired radiation intensity.

In general, lower burner inputs can be used for lower mounting heights and where lower heat gains are required. Higher burner inputs are used primarily with higher mounting heights and where high heat gain is required.

The number of burners required can be calculated by dividing the input rating of the selected sizes into the

calculated CRV-Series system required installed capacity.

4.4 Radiant Distribution

Radiant heat distribution at occupant level must be considered in the burner and design selection process.

Distribution of heat between radiant branches at floor level is more critical at the perimeter of buildings. This is where the heat loss is highest. Therefore, it may be possible to combine different applications of distribu- tion within the same building. The following figures show three different applications of rules to determine distribution.

4.4.1 Radiant Distribution (Average Coverage)

The aim of this distribution is to provide average or lighter than average radiant intensity and works well for general building heating. See Page 11, Figure 11. The distance between radiant branches can vary between 2.5 to 4 (or more) times the mounting height.

This distribution is commonly used in applications such as warehouses and lower heat loss areas of a building.

Lighter coverage can be used in areas where occu- pant traffic is low.

4.4.2 Radiant Distribution (Increased Coverage)

The aim of this distribution is to provide continuous radiant intensity. See Page 11, Figure 12. The distance between radiant branches is about 2 times the mounting height.

This distribution is commonly used in areas bordering high heat loss areas or areas requiring increased radi- ant intensity to achieve occupant comfort.

4.4.3 Radiant Distribution (Heavy Coverage)

The aim of this distribution is to provide increased radi- ant intensity in areas that range from sedentary work to spot heating for loading docks. See Page 11, Figure 13. The y dimensions in the diagram is the height above floor level where overlap of the radiant output will occur.

In practice, y = 6' (1.83 m) is commonly used in areas where occupant comfort doing sedentary work is an important factor. In loading bays, spot heating and areas of high heat loss, the horizontal distance (x) between branches can be as little as 0.5 times the mounting height.

10

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Design Manual Page Roberts-Gordon LLC Page Table of Figures Page Concept CRV-SERIES System SafetyZero Regulator Assembly Overview Two Branch System Shown Fuel Savings and Comfort Clearances to combustibles at all times for safety Standard Reflector ONE Side ReflectorUniversal SHIELD, Position Foot Deco Grille Radiant Adjustment to Heat Loss Radiant Height Adjustment FactorSizing and Design Considerations ExampleSelecting the Burners Radiant DistributionRadiant Distribution Average Coverage Radiant Distribution Increased Coverage= mounting height Flow Loading Radiant Branch FlowBurner Flow Units Tailpipe Flow Pump CapacityPump Exhaust Length Requirements Radiant Tube and Tailpipe Radiant Tube LengthMinimum Radiant Tube Length Maximum Radiant Tube LengthDesign Parameters Pump Model Series Maximum LoadingCRV-Series Design Methods Flow Units Per BranchAfter Each Burner Allowable Tailpipe Lengths Burner ModelTailpipe Design Method Rule of Thumb Unshared CalculationsSystem with EP-300 Series Pump To Calculate the Total System TailpipeDamper Couplings Possible Damper Coupling Locations Example CRV-SERIES System Layouts Example System Layout Option12 m 10 3 m 20 6 m 12 m Tailpipe 10 3 m 100 30 m Example System Layout Option 7, 8 Roberts Gordon System Control P/N Control MethodsRoberts Gordon Ultravac Pressure Switch AIR Supply System PressurizedNon-Pressurized Pressurized SystemsDuct Design Rules Pipe sizingBlower P/N 90707501 Performance 112 Flow Units Sample Layout for Pressurized Outside Air Systems Roberts Gordon Ultravac Design Requirements CRV-SERIES Equipment Specifications Page Maintain Clearance Side Clearance below
Related manuals
Manual 72 pages 5.13 Kb

CRV-B-4, CRV-B-2, CRV-B-6, CRV-B-8 specifications

Roberts Gorden is renowned for its innovative heating solutions, particularly the CRV series of infrared radiant heaters, which include models CRV-B-2, CRV-B-4, CRV-B-6, and CRV-B-8. These heaters are designed to provide effective and efficient heating, making them ideal for various industrial, commercial, and agricultural applications.

One of the standout features of the Roberts Gorden CRV series is its advanced infrared heating technology. Unlike conventional heating systems that heat the air, infrared heaters warm objects and people directly, allowing for a more energy-efficient and comfortable environment. This makes the CRV series particularly effective in large spaces, such as warehouses, manufacturing facilities, and greenhouses.

The CRV-B models are engineered for versatility and can be mounted in various configurations, including horizontal and vertical placements, providing installation flexibility. Each model is available in different sizes and heating outputs, ensuring that users can select a unit tailored to their specific heating requirements. The CRV-B-2, for instance, is ideal for smaller spaces, while the CRV-B-8 offers higher power for larger areas.

Moreover, these heaters come equipped with advanced control systems that allow for precise temperature regulation. The units can be integrated with building management systems, enabling users to monitor and adjust settings remotely. This feature not only enhances comfort but also contributes to energy savings, as the heaters can be programmed to operate only during necessary hours.

Structural durability is another significant characteristic of the CRV series. Constructed with high-quality materials, the heaters are designed to withstand the rigors of industrial environments while maintaining optimal performance over time. The reflective surfaces enhance heat distribution, ensuring that warmth is evenly distributed throughout the space.

Safety is paramount with Roberts Gorden’s CRV heaters. They are designed with built-in safety mechanisms, including overheat protection and automatic shut-off features to prevent accidents.

Overall, the Roberts Gorden CRV-B-2, CRV-B-4, CRV-B-6, and CRV-B-8 models exemplify cutting-edge infrared heating technology, delivering effective, efficient, and reliable heating solutions tailored to diverse applications. With a combination of flexibility, advanced control capabilities, and safety features, these heaters are an excellent choice for anyone in need of powerful heating solutions.
Top Page Image Contents