Goodman Mfg PG 15 specifications Circulating AIR and Filters, Horizontal Air Flow

Page 10

For unit protection, use a fuse or HACR circuit breaker that is in excess of the circuit ampacity, but less than or equal to the maximum overcurrent protection device. DO NOT EXCEED THE MAXIMUM OVERCURRENT DEVICE SIZE SHOWN ON UNIT DATA PLATE.

All line voltage connections must be made through weatherproof fittings. All exterior power supply and ground wiring must be in approved weatherproof conduit. Low voltage wiring from the unit control panel to the thermostat requires coded cable. See below for ground level and rooftop wiring.

Note:Junction box location shown is optional and is for illustration purposes only.

JUNCTION BOX

Electrical Power Directly To Junction Box

Electrical Power Routed Through Bottom of Unit

Typical Electrical Wiring Unit Voltage

UNIT VOLTAGE

The unit transformer is factory connected for 230V operation. If the unit is to operate on 208V, reconnect the transformer primary lead as shown on the unit wiring diagram. The induced draft blower on some models is equipped with a low speed 230V lead (blue) and a low speed 208V lead (black). If equipped, connect the induced draft blower low speed 208V lead (black) in place of the low speed 230V lead (blue). Place the unused 230V lead on the “PARK” terminal located on ignition control.

HEAT ANTICIPATOR SETTING

The heat anticipator is to be set by measuring the load (amperage) at the “R” circuit. Follow the instructions provided with the thermostat for more details.

CIRCULATING AIR AND FILTERS

AIRFLOW CONVERSION

Units can easily be converted from horizontal to down- discharge airflow delivery. In down-discharge or high static installations, the installer should measure the total external static and review the blower performance charts before performing the installation. In some installations it will be necessary to change the blower speed to provide proper air flow.

Horizontal Air Flow

Single phase models are shipped without horizontal duct covers. If needed, these kits may be ordered through Goodman’s Service Parts department.

Duct Cover Installation

Down Discharge Applications

Cut insulation around bottom openings and remove panels from the bottom of the unit, saving the screws holding the panels in place.

NOTE: Single phase models require installation of horizontal duct kit #20464501PDGK (medium chassis) and #20464502PDGK (large chassis).

DUCTWORK

Duct systems and register sizes must be properly designed for the C.F.M. and external static pressure rating of the unit. Ductwork should be designed in accordance with the recommended methods of Air Conditioning Contractors of America Manual D (Residential) or Manual Q (Commercial).

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents PG 15 Seer M Series Ansi Z21.47CSA-2.3 Central FurnacesIndex Index Replacement Parts Safety InstructionsOutside Slab Installation Unit LocationRooftop Installation Roof Curb InstallationRigging Rigging DetailsGAS Piping Natural Gas ConnectionProper Piping Practice Typical Propane Gas PipingTwo-Stage Heating with Two-Stage Cooling Thermostat Diagram Electrical WiringPropane Gas Pipe Sizing Circulating AIR and Filters Duct Cover Installation Down Discharge ApplicationsHorizontal Air Flow Condensate Drain Filter InstallationVenting Drain ConnectionNormal Sequences of Operation STARTUP, ADJUSTMENTS, and ChecksHeat Anticipator Setting Rollout Protection ControlSecondary Limit Control Pre-Operation Checks With Power And Gas OffWith Power And Gas On Gas Supply And Manifold CheckManifold Gas Pressure Range Nominal Temperature Rise CheckBlower Speed Adjustments Gas Input Natural Gas Only CheckTroubleshooting Check wiring Maintenance Flame SensorFunctional Parts List Accessories and Functional PartsManifold Assembly Burner FlameAppendix Ignition Control Diagnostic Indicator Chart Dimension Medium Large YL/BK BL/PK LPS 0140G00533 REV a PG15*****41B* Wiring Diagram PG15*****41B* Wiring Diagram Unit Ton 2 Ton 2 -/ 4 Ton= Outside of Temperature Rise Range Not Recommended Before Calling Your Servicer

PG 15 specifications

Goodman Manufacturing's PG 15 series stands out in the competitive HVAC market as a high-efficiency, cost-effective option for both residential and light commercial applications. This product line is particularly valued for its reliable performance and innovative technologies, which focus on energy efficiency, durability, and user comfort.

One of the main features of the PG 15 is its SEER (Seasonal Energy Efficiency Ratio) rating, which reflects its ability to provide superior cooling while using less energy. The higher the SEER rating, the more efficiently the unit operates, leading to significant savings on energy bills. The PG 15 boasts an impressive SEER rating, making it an ideal choice for conscientious consumers looking to lower their utility costs.

Incorporating advanced technologies, the PG 15 features a high-efficiency scroll compressor. This design minimizes vibration and noise, providing a quieter operation that enhances overall comfort in the living or working environment. Additionally, the compressor is designed for longevity, reducing maintenance needs and enhancing the unit's lifespan.

Another notable characteristic of the PG 15 is its durable construction. The unit is built with a galvanized steel cabinet that is protected with a rust-resistant finish, ensuring it withstands the rigors of harsh weather conditions. The 15-inch fan motor and multi-speed blower also contribute to efficient airflow and improved indoor air quality, while the refrigerant management system aids in efficient cooling performance.

Installation versatility is another advantage of the PG 15 series. Designed to accommodate a range of installation setups, this system can easily integrate into existing frameworks, making it suitable for both new constructions and retrofits.

Furthermore, Goodman Mfg places emphasis on customer satisfaction and support. The PG 15 series comes with a comprehensive warranty, offering peace of mind to homeowners and business owners alike. This commitment to quality and customer service has helped Goodman establish a reputation for reliability and performance in the HVAC industry.

In summary, the Goodman PG 15 stands out due to its energy-efficient design, advanced technologies, durable construction, and versatile installation options, making it a compelling choice for anyone seeking an effective and reliable HVAC solution.
Top Page Image Contents