Goodman Mfg PG 15 specifications 0140G00533 REV a

*PG15*****41A* WIRING DIAGRAM

HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING.

MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.

L1			SUPPLY VOLTAGE					L2
			208-230/1/60
CC	T1		R			T2	CC
L1			C			C
	LO		S		H			L2
INTEGRATED IGNITION CONTROL
	HI			CM	F			INTEGRATED IGNITION CONTROL
	LO						L2
	HI			VM			L2
	L1			EM			L2
	L1				SEE NOTE 2		L2
P1 2 TH		F			TR
			ALS	LS		RS

		1	HLO
R		3	HLI		PS
			PSW
W 1		6
W 2		8	PSW
	TO	9	MVL			M
	MICRO						GV
			MVH
Y2		7				HI
C		5	MVC			C
Y1		P2 1	COM
	CONTROL	4
		5			HPS
			LPS
		3
	IGNITION						SEE NOTE 7
					SEE NOTE 8
	INTERGRATED	6		1	ECON	5	CC
		2		2	ECON	5
					SOL
			ECON	3	ECON	4
			LO HEAT
G	TO		HI HEAT				EM C
			LO COOL
	MICRO
			HI COOL

COMPONENT LEGEND		FACTORY WIRING
ALS	AUXILLARY LIMIT SWITCH	LINE VOLTAGE
COMP	COMPRESSOR	LOW VOLTAGE
CM	CONDENSER MOTOR	OPTIONAL HIGH VOLTAGE

CCCONTACTOR

ECON ECONOMIZER

EM	EVAPORATOR MOTOR	FIELD WIRING
F	FUSE	HIGH VOLTAGE
FS	FLAME SENSOR	LOW VOLTAGE
GND	EQUIPMENT GROUND
GV	GAS VALVE	WIRE CODE
IIC	INTEGRATED IGNITION CONTROL	BK	BLACK
IGN	IGNITOR
		BL	BLUE
LS	LIMIT SWITCH
		BR	BROWN
PS	PRESSURE SWITCH	GR	GREEN
RCCF	RUN CAPACITOR FOR COMPRESSOR/FAN	OR	ORANGE
RS	ROLLOUT SWITCH	PK	PINK
SOL	SOLENOID (2ND STAGE COOL)	PU	PURPLE
TR	TRANSFORMER	RD	RED
VM	VENT MOTOR	WH	WHITE
		YL	YELLOW

NOTES

1.REPLACEMENT WIRE MUST BE THE SAME SIZE AND TYPE OF INSULATION AS ORIGINAL.(USE COPPER CONDUCTOR ONLY).

2.FOR 208 VOLT TRANSFORMER OPERATION MOVE BLACK WIRE FROM TERMINAL 3 TO TERMINAL 2 ON TRANSFORMER.

3.USE COPPER CONDUCTORS ONLY.

4.FOR 208V OPERATION, REMOVE BLUE LEAD FROM INDUCER LOW TERMINAL. MOVE BLACK LEAD FROM PARK TERMINAL ONTO INDUCER LOW TERMINAL. PLACE BLUE LEAD ON PARK TERMINAL.

5.USE NEC CLASS 2 WIRE FOR THERMOSTAT FIELD WIRING.

6.COMPRESSOR 2ND STAGE SOLENOID NOT PRESENT ON ALL MODELS.

7.OPTIONAL REFRIGERANT SWITCHES

8.FOR ECONOMIZER, REMOVE PLUG FROM ECONOMIZER HARNESS. CONNECT PLUG FROM ECONOMIZER TO HARNESS.

DIAGNOSTIC	STATUS	CHECK
LED - RED
ON	NORMAL OPERATION	-
OFF	NO POWER OR	CHECK INPUT POWER
	INTERNAL CONTROL	CHECK FUSE(S)
	FAULT
		GAS FLOW
1 FLASH	IGNITION FAILURE	GAS PRESSURE
		GAS VALVE
		FLAME SENSOR
2 FLASHES	PRESSURE SWITCH OPEN	CHECK PRESSURE SWITCH
		CHECK TUBING
		CHECK VENT MOTOR
3 FLASHES	PRESSURE SWITCH CLOSED	CHECK PRESSURE SWITCH
	WITHOUT INDUCER ON	CHECK WIRING FOR SHORTS
4 FLASHES	OPEN LIMIT SWITCH	CHECK MAIN LIMIT SWITCH
		CHECK AUXILIARY LIMIT SW.
		CHECK ROLLOUT LIMIT SW.
5 FLASHES	FALSE FLAME DETECTED	CHECK GAS VALVE
		CHECK FOR SHORTS IN
		FLAME SENSOR WIRING
6 FLASHES	COMPR. SHORT CYCLE DELAY	3 MIN COMP. SHORT
		CYCLE DELAY

DIAGNOSTIC	STATUS	CHECK
LED - RED
7 FLASHES	LIMIT OPEN 5 TIMES IN	CHECK MAIN LIMIT SWITCH
	SAME CALL FOR HEAT	CHECK AUXILIARY LIMIT SW.
		CHECK JUMPER BETWEEN
		1 AND 4 ON 6-CIRCUIT
8 FLASHES	IDT/ODT OPEN	CONNECTOR
		CHECK OPTIONAL
		REFRIGERANT SWITCHES
9 FLASHES	PSW/LOC OPEN	CHECK REFRIGERANT
		SWITCHES FOR LOSS OF
		CHARGE OR HIGH HEAD
		PRESSURE
DIAGNOSTIC	STATUS	CHECK
LED - AMBER
OFF	NO FLAME PRESENT	-
ON	NORMAL FLAME PRESENT	-
1 FLASH		GAS FLOW
	LOW FLAME SIGNAL	GAS PRESSURE
		GAS VALVE
		FLAME SENSOR
2 FLASHES	FALSE FLAME DETECTED	CHECK GAS VALVE
		CHECK FOR SHORTS IN
		FLAME SENSOR WIRING

0140G00533 REV A

Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.

23