Heat & Glo LifeStyle Cosmo-130 owner manual Installing Vent Pipe and Appliance, Vent Limits

Page 21

8 Installing Vent Pipe and Appliance

A. Vent Limits

The abbreviations listed in this vent table key are used in the vent diagrams.

B. Venting Components

CAUTION! Risk of Cuts/Abrasions/Flying Debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp.

Description

Minimum Vertical Run Length 10 ft.

Maximum Vertical Run Length 50 ft.

Horizontal venting is NOT allowed.

Vertical terminations are measured to top of chimney.

This appliance is listed for use with LINK-DV systems and components only. It is permissible to extend venting above existing chimney (within specifi ed maximum verti- cal limits) using SL-D series or Dura Vent GS series 4 in. x 6-5/8 in. gas direct-vent pipe. Connection is made us-

ing DV-46DVA-GK. The vent must be terminated with the cap supplied with the LINK-series vent kit.

WARNING! Risk of Fire/Explosion/Asphyxiation! Do NOT connect this gas appliance to a chimney flue serving a separate solid fuel or gas burning appliance.

•May impair safe operation of this appliance or other appliances connected to the flue.

•Vent this appliance directly outside.

•Use separate vent system for this appliance.

CAUTION! ALL vent specifications MUST be followed. This product is tested and listed to these specifications. Appliance performance will suffer if specifications are not followed.

The vertical vent termination system installed on this model includes:

•Flexible vent pipe for exhaust air (included with vent kit).

•One length of 3-inch fl exible vent pipe for combustion air (included with vent kit).

•One pipe-to-cap adaptor (included with vent kit).

•One vertical termination cap (included with vent kit).

C. Connecting Vent Pipe

Reference instructions in the termination kit.

•Install the 3-inch fl exible vent pipe(s) down through the chimney.

•Secure the exhaust flexible vent pipe to the exhaust starting collar on top of the appliance with three screws and seal with stove cement rated for continuous exposure to 1200ºF or higher. See Figure 8.1.

•Use 3 screws to attach the section of inlet air vent to the inlet collar on the collar slide plate and seal with stove cement rated for continuous exposure to 1200ºF or higher. See Figure 8.1. NOTE: The collar slide plate may be removed from appliance to aid installation.

 

TERMINATION

 

ADAPTER

CAP

 

 

 

 

INLET

 

 

COLLAR

 

 

EXHAUST

 

 

COLLAR

 

 

 

INLET AIR STARTING COLLAR

 

EXHAUST

LOCKING TAB

 

AIR

 

 

V = 10 FT. MINIMUM

VENT PIPE

 

 

 

50 FT. MAXIMUM

 

 

 

 

STARTING COLLAR BRACKET

HANDLE

 

 

 

 

EXHAUST STARTING COLLAR

 

INLET AIR

 

 

VENT PIPE

 

 

INLET AIR STARTING COLLAR

 

 

 

NOTE: TO ACHIEVE OPTIMUM PERFOR-

 

 

MANCE OF INSERT, MINIMIZE OR AVOID

 

STARTING COLLAR BRACKET

BENDS IN EXHAUST VENT PIPE.

 

 

 

EXHAUST STARTING COLLAR

 

Figure 8.1

 

 

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Models Cosmo-I30 Cosmo-I35 What to do if you smell gasHOT Surfaces Homeowner Reference Information CongratulationsUser Guide Table of ContentsLimited Lifetime Warranty Limited Lifetime Warranty Listing and Code Approvals Gas Fireplace Safety Operating Instructions User GuideYour Fireplace Remote Controls, Wall Controls and Wall Switches Fixed Glass AssemblyIPI Battery Tray/Battery Installation Clear SpaceModule Reset Control Module OperationBefore Lighting Fireplace Final inspection by Lighting Instructions IPIWhat to do if YOU Smell GAS GAS ValveFrequently Asked Questions Issue SolutionsAfter Appliance is Lit Maintenance Tasks-Homeowner Maintenance and ServiceGlass Cleaning Remote ControlGasket Seal and Glass Assembly Inspection Maintenance Tasks-Service TechnicianVenting FireboxIPI Pilot Flame Patterns Burner Ignition and OperationTypical Appliance System Getting StartedDesign and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Minimum Fireplace Opening Fireplace Size RequirementsTOP View Front View Side View Minimum Fireplace Size COSMO-I35 COSMO-I30TOP View Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsInstallation Preparation Connecting Vent Pipe Installing Vent Pipe and ApplianceVent Limits Venting ComponentsPlacing, Securing and Leveling the Appli- ance Location of AUX300 for Remote Control Blower FunctionMasonry Installing Adaptor and Termination CapFactory Built Wood Burning Damper Flashing Kit OptionalFuel Conversion Gas InformationGas Pressure Gas ConnectionIntelliFire Plus Ignition System Wiring Wiring RequirementsON/OFF Switch Electrical InformationFAN Blades Optional Accessories RequirementsAUX 300 Module FAN WHT GRN BLK Blowers Fan Wiring with RemoteClearances to Mantels or other Combustibles above Appliance FinishingAppliance Setup Air Shutter Setting Air Shutter SettingsCOSMO-I30 COSMO-I35 Troubleshooting Symptom Possible Cause Corrective ActionIntelliFire Plus Ignition System Main burner will not Appliance Dimension Diagram Model DimensionsReference Materials Direct Vent Flex Liner Kits Vent Kits ComponentsContact Information

Cosmo-130 specifications

The Heat & Glo LifeStyle Cosmo-130 is a modern gas fireplace that exemplifies innovation in heating design and functionality. This fireplace blends contemporary style with advanced technology, making it a perfect addition for any contemporary living space. Its sleek and minimalist design ensures that it not only serves as a heat source but also as a striking focal point in your home.

One of the main features of the Cosmo-130 is its impressive viewing area. The large glass front allows for an unobstructed view of the flames, creating an inviting ambiance. The design prioritizes aesthetics, with the fireplace being available in multiple configurations, including linear and traditional styles, enabling it to fit seamlessly into various interior designs.

With a focus on efficiency, the Cosmo-130 operates using an advanced gas burner system, which optimizes fuel use while producing substantial heat output. This fireplace boasts an impressive thermal efficiency rating, ensuring that heat is effectively distributed throughout the room while minimizing energy consumption.

The LifeStyle Cosmo-130 employs cutting-edge technology with its intuitive electronic controls. Homeowners can easily adjust the flame height and heat output to suit their preferences using a remote control or a smartphone app. This level of control contributes not only to comfort but also to energy efficiency, allowing users to personalize their heating experience.

Another notable aspect is the fireplace's customizable media options. Customers can choose from various decorative media, including logs, crystals, or stones, allowing for personalization to match different décor styles. This flexibility enhances the visual appeal of the fireplace and caters to individual tastes.

Safety is paramount in the design of the LifeStyle Cosmo-130. It includes features such as a thermostat that automatically maintains desired temperatures, as well as a safety shut-off system that activates should the unit overheat. This ensures peace of mind for users, especially in homes with children and pets.

With an emphasis on convenience and style, the Heat & Glo LifeStyle Cosmo-130 is an exceptional choice for those looking to enhance their home with a sophisticated heating solution. Its combination of aesthetic appeal, user-friendly technology, and efficient performance make it a standout option in the world of modern fireplaces, promising warmth and elegance in any setting.
Top Page Image Contents