Heat & Glo LifeStyle Cosmo-130 owner manual Troubleshooting, IntelliFire Plus Ignition System

Page 31

13 Troubleshooting

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualifi ed technician in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualifi ed technician. Contact your dealer to arrange a service call by a qualifi ed technician.

A. IntelliFire Plus™ Ignition System

Symptom

Possible Cause

Corrective Action

 

 

 

1. Pilot won’t light.

A. Incorrect wiring.

Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are

The ignitor/module

 

connected to correct terminals on module and pilot assembly.

makes noise, but no

 

 

B. Loose connections or electrical

Verify no loose connections or electrical shorts in wiring from mod-

spark.

 

shorts in the wiring.

ule to pilot assembly. Verify connections underneath pilot assembly

 

 

are tight; also verify igniter and fl ame sense wires are not grounding

 

 

out to metal chassis, pilot burner, pilot enclosure, mesh screen if

 

 

present, or any other metal object.

 

 

 

 

C. Ignitor gap is too large.

Verify gap of igniter to right side of pilot hood. The gap should be

 

 

approximately .17 in. or 1/8 in. (3 mm).

 

 

 

2. Pilot won’t light,

A. No power, transformer installed

Verify that transformer is installed and plugged into module. Check

there is no noise or

incorrectly, or depleted batteries.

voltage of transformer at connection to module. Acceptable read-

spark.

 

ings of a good transformer are between 6.4 and 6.6 volts AC. Bat-

 

 

tery power supply voltage must be at least 4 volts. If below 4 volts,

 

 

replace batteries.

 

 

 

 

B. A shorted or loose connection in

Remove and reinstall the wiring harness that plugs into module.

 

wiring confi guration or wiring har-

Verify there is a tight fi t. Verify pilot assembly wiring to module. Re-

 

ness.

move and verify continuity of each wire in wiring harness. Replace

 

 

any damaged components.

 

 

 

 

C. Improper wall switch wiring.

Verify that 120/VAC power is “ON” to junction box.

 

 

 

 

D. Module not grounded.

Verify black ground wire from module wire harness is grounded to

 

 

metal chassis of appliance.

 

 

 

3. Pilot sparks, but

A. Gas supply.

Verify that incoming gas line ball valve is “open”. Verify that inlet

Pilot will not light.

 

pressure reading is within acceptable limits.

 

 

 

 

B. Ignitor gap is too large.

Verify gap of igniter to right side of pilot hood. The gap should be

 

 

approximately .17 in. or 1/8 in. (3 mm).

 

 

 

 

C. Module is not grounded.

Verify module is securely grounded to metal chassis of appliance.

 

 

 

 

D. Pilot valve solenoid

Verify that 1.5 to 1.8 VDC is supplied to pilot solenoid from module.

 

 

If below 1.5 volts, replace module. If 1.5 volts or greater, replace

 

 

valve.

 

 

 

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents What to do if you smell gas Models Cosmo-I30 Cosmo-I35HOT Surfaces Homeowner Reference Information CongratulationsUser Guide Table of ContentsLimited Lifetime Warranty Limited Lifetime Warranty Listing and Code Approvals Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches IPI Battery Tray/Battery InstallationControl Module Operation Module ResetBefore Lighting Fireplace GAS Valve Lighting Instructions IPIFinal inspection by What to do if YOU Smell GASIssue Solutions Frequently Asked QuestionsAfter Appliance is Lit Remote Control Maintenance and ServiceMaintenance Tasks-Homeowner Glass CleaningFirebox Maintenance Tasks-Service TechnicianGasket Seal and Glass Assembly Inspection VentingIPI Pilot Flame Patterns Burner Ignition and OperationTypical Appliance System Getting StartedTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components COSMO-I35 COSMO-I30 Fireplace Size RequirementsMinimum Fireplace Opening TOP View Front View Side View Minimum Fireplace SizeTOP View Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Vent LimitsPlacing, Securing and Leveling the Appli- ance Location of AUX300 for Remote Control Blower FunctionDamper Flashing Kit Optional Installing Adaptor and Termination CapMasonry Factory Built Wood BurningGas Connection Gas InformationFuel Conversion Gas PressureElectrical Information Wiring RequirementsIntelliFire Plus Ignition System Wiring ON/OFF SwitchFAN Blades Optional Accessories RequirementsAUX 300 Module FAN WHT GRN BLK Blowers Fan Wiring with RemoteClearances to Mantels or other Combustibles above Appliance FinishingAppliance Setup Air Shutter Settings Air Shutter SettingCOSMO-I30 COSMO-I35 Symptom Possible Cause Corrective Action TroubleshootingIntelliFire Plus Ignition System Main burner will not Model Dimensions Appliance Dimension DiagramReference Materials Direct Vent Flex Liner Kits Vent Kits ComponentsContact Information

Cosmo-130 specifications

The Heat & Glo LifeStyle Cosmo-130 is a modern gas fireplace that exemplifies innovation in heating design and functionality. This fireplace blends contemporary style with advanced technology, making it a perfect addition for any contemporary living space. Its sleek and minimalist design ensures that it not only serves as a heat source but also as a striking focal point in your home.

One of the main features of the Cosmo-130 is its impressive viewing area. The large glass front allows for an unobstructed view of the flames, creating an inviting ambiance. The design prioritizes aesthetics, with the fireplace being available in multiple configurations, including linear and traditional styles, enabling it to fit seamlessly into various interior designs.

With a focus on efficiency, the Cosmo-130 operates using an advanced gas burner system, which optimizes fuel use while producing substantial heat output. This fireplace boasts an impressive thermal efficiency rating, ensuring that heat is effectively distributed throughout the room while minimizing energy consumption.

The LifeStyle Cosmo-130 employs cutting-edge technology with its intuitive electronic controls. Homeowners can easily adjust the flame height and heat output to suit their preferences using a remote control or a smartphone app. This level of control contributes not only to comfort but also to energy efficiency, allowing users to personalize their heating experience.

Another notable aspect is the fireplace's customizable media options. Customers can choose from various decorative media, including logs, crystals, or stones, allowing for personalization to match different décor styles. This flexibility enhances the visual appeal of the fireplace and caters to individual tastes.

Safety is paramount in the design of the LifeStyle Cosmo-130. It includes features such as a thermostat that automatically maintains desired temperatures, as well as a safety shut-off system that activates should the unit overheat. This ensures peace of mind for users, especially in homes with children and pets.

With an emphasis on convenience and style, the Heat & Glo LifeStyle Cosmo-130 is an exceptional choice for those looking to enhance their home with a sophisticated heating solution. Its combination of aesthetic appeal, user-friendly technology, and efficient performance make it a standout option in the world of modern fireplaces, promising warmth and elegance in any setting.
Top Page Image Contents