Heat & Glo LifeStyle Cosmo-130 Gas Information, Fuel Conversion, Gas Pressure, Gas Connection

Page 24

9 Gas Information

A. Fuel Conversion

•Make sure the appliance is compatible with available gas types.

•Conversions must be made by a qualified technician (NFI certifi ed or factory-trained) using Hearth & Home Technologies specifi ed and approved parts.

B. Gas Pressure

•Optimum appliance performance requires proper input pressures.

•Gas line sizing requirements will be determined in ANSI Z223.1 National Fuel Gas Code in the USA and CAN/ CGA B149 in Canada.

•Pressure requirements are:

Gas Pressure

Natural Gas

Propane

Minimum inlet pressure

5.0 in. w.c.

11.0 in. w.c.

Maximum inlet pressure

10.0 in. w.c.

13.0 in. w.c.

Manifold pressure

3.5 in. w.c.

10.0 in. w.c.

C. Gas Connection

•Refer to Reference Section 15 for location of gas line access in appliance.

•Gas line may be run through knockout(s) provided.

•The gap between supply piping and gas access hole may be caulked with caulk with a minimum of 300ºF continuous exposure rating or stuffed with non-combustible, unfaced insulation to prevent cold air infiltration.

•Ensure that gas line does not come in contact with outer wrap of the appliance. Follow local codes.

•Pipe incoming gas line into valve compartment.

•Connect incoming gas line to the 1/2 in. (13 mm) connection on manual shutoff valve.

WARNING! Risk of Fire/Explosion! Support control when attaching pipe to prevent bending gas line.

• A small amount of air will be in the gas supply lines.

WARNING! Risk of Fire/Explosion! Gas build-up during line purge could ignite.

WARNING! Risk of Fire/Explosion! High pressure will damage valve. Low pressure may cause explosion.

•Verify inlet pressures. Verify minimum pressures when other household gas appliances are operating.

•Install regulator upstream of valve if line pressure is greater than 1/2 psig.

WARNING

Fire Risk. Explosion Hazard.

High pressure will damage valve.

• Disconnect gas supply piping BEFORE pressure testing gas line at test pressures above 1/2 psig.

•Close the manual shutoff valve BEFORE pressure testing gas line at test pressures equal to or less than 1/2 psig.

Note: Have the gas supply line installed in accordance with local codes, if any. If not, follow ANSI 223.1. Installation should be done by a qualifi ed installer approved and/or licensed as required by the locality. (In the Commonwealth of Massachusetts installation must be performed by a licensed plumber or gas fi tter).

Note: A listed (and Commonwealth of Massachusetts ap- proved) 1/2 inch (13 mm) T-handle manual shut-off valve and fl exible gas connector are connected to the 1/2 inch (13 mm) control valve inlet.

•If substituting for these components, please consult local codes for compliance.

•Purge should be performed by technician certified by NFI or factory-trained.

•Ensure adequate ventilation.

•Ensure there are no ignition sources such as sparks or open flames.

Light the appliance. It will take a short time for air to purge from lines. When purging is complete the appliance will light and operate normally.

WARNING! Risk of Fire, Explosion or Asphyxiation! Check all fittings and connections with a non-corrosive commercially available leak-check solution. DO NOT use open flame. Fittings and connections could have loos- ened during shipping and handling.

WARNING! Risk of Fire! DO NOT change valve settings. This valve has been preset at the factory.

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 2000 feet elevation:

•In the USA: Reduce burner orifice 4% for each 1000 feet above 2000 feet.

•In the CANADA: Reduce burner orifice 10% for elevations between 2000 feet and 4500 feet. Above 4500 feet, consult local gas utility.

24

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Models Cosmo-I30 Cosmo-I35 What to do if you smell gasHOT Surfaces Congratulations Homeowner Reference InformationTable of Contents User GuideLimited Lifetime Warranty Limited Lifetime Warranty Listing and Code Approvals Gas Fireplace Safety Operating Instructions User GuideYour Fireplace Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesIPI Battery Tray/Battery Installation Clear SpaceModule Reset Control Module OperationBefore Lighting Fireplace Lighting Instructions IPI Final inspection byWhat to do if YOU Smell GAS GAS ValveFrequently Asked Questions Issue SolutionsAfter Appliance is Lit Maintenance and Service Maintenance Tasks-HomeownerGlass Cleaning Remote ControlMaintenance Tasks-Service Technician Gasket Seal and Glass Assembly InspectionVenting FireboxBurner Ignition and Operation IPI Pilot Flame PatternsGetting Started Typical Appliance SystemDesign and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Fireplace Size Requirements Minimum Fireplace OpeningTOP View Front View Side View Minimum Fireplace Size COSMO-I35 COSMO-I30Mantel and Wall Projections TOP ViewTermination Locations Vent Termination Minimum ClearancesInstallation Preparation Installing Vent Pipe and Appliance Connecting Vent PipeVent Limits Venting ComponentsLocation of AUX300 for Remote Control Blower Function Placing, Securing and Leveling the Appli- anceInstalling Adaptor and Termination Cap MasonryFactory Built Wood Burning Damper Flashing Kit OptionalGas Information Fuel ConversionGas Pressure Gas ConnectionWiring Requirements IntelliFire Plus Ignition System WiringON/OFF Switch Electrical InformationOptional Accessories Requirements FAN BladesFan Wiring with Remote AUX 300 Module FAN WHT GRN BLK BlowersFinishing Clearances to Mantels or other Combustibles above ApplianceAppliance Setup Air Shutter Setting Air Shutter SettingsCOSMO-I30 COSMO-I35 Troubleshooting Symptom Possible Cause Corrective ActionIntelliFire Plus Ignition System Main burner will not Appliance Dimension Diagram Model DimensionsReference Materials Vent Kits Components Direct Vent Flex Liner KitsContact Information

Cosmo-130 specifications

The Heat & Glo LifeStyle Cosmo-130 is a modern gas fireplace that exemplifies innovation in heating design and functionality. This fireplace blends contemporary style with advanced technology, making it a perfect addition for any contemporary living space. Its sleek and minimalist design ensures that it not only serves as a heat source but also as a striking focal point in your home.

One of the main features of the Cosmo-130 is its impressive viewing area. The large glass front allows for an unobstructed view of the flames, creating an inviting ambiance. The design prioritizes aesthetics, with the fireplace being available in multiple configurations, including linear and traditional styles, enabling it to fit seamlessly into various interior designs.

With a focus on efficiency, the Cosmo-130 operates using an advanced gas burner system, which optimizes fuel use while producing substantial heat output. This fireplace boasts an impressive thermal efficiency rating, ensuring that heat is effectively distributed throughout the room while minimizing energy consumption.

The LifeStyle Cosmo-130 employs cutting-edge technology with its intuitive electronic controls. Homeowners can easily adjust the flame height and heat output to suit their preferences using a remote control or a smartphone app. This level of control contributes not only to comfort but also to energy efficiency, allowing users to personalize their heating experience.

Another notable aspect is the fireplace's customizable media options. Customers can choose from various decorative media, including logs, crystals, or stones, allowing for personalization to match different décor styles. This flexibility enhances the visual appeal of the fireplace and caters to individual tastes.

Safety is paramount in the design of the LifeStyle Cosmo-130. It includes features such as a thermostat that automatically maintains desired temperatures, as well as a safety shut-off system that activates should the unit overheat. This ensures peace of mind for users, especially in homes with children and pets.

With an emphasis on convenience and style, the Heat & Glo LifeStyle Cosmo-130 is an exceptional choice for those looking to enhance their home with a sophisticated heating solution. Its combination of aesthetic appeal, user-friendly technology, and efficient performance make it a standout option in the world of modern fireplaces, promising warmth and elegance in any setting.
Top Page Image Contents