Heat & Glo LifeStyle Cosmo-130 owner manual Placing, Securing and Leveling the Appli- ance

Page 22

CUT AND BEND

FLASHING AS NEEDED

TO FIT CHIMNEY

SEALANT

ADHESIVE

Figure 8.2

•Trim chimney top plate to minimize excess overhang or bend over fl ue tile (see Figure 8.2).

•Place 3/8 inch bead of 300º F silicone on fl ue tile top.

D.Placing, Securing and Leveling the Appli- ance

•Install insert (without surround attached) into existing fi replace while pulling collar slide plate forward.

•Install gas line into hole provided on insert side.

•If applicable install remote control wires into insert side (see Section 8.E).

•Secure collar slide plate to appliance by placing locking handle into position with locking tabs (see Figure 8.1) and secure with #8 screw.

•Level the appliance from side to side and front to back. If necessary, use the leveling legs included with the manual bag to set each corner of the base.

•Position any excess flexible vent pipe back up into chimney without sagging. Twist and push flex vent together to shorten.

•Install fiberglass insulation pieces to back face of surround.

•Attach surround. Follow instructions for surround installation included with the front.

•Push insert into the opening so that it tightly overlaps the fi replace opening.

WARNING! Risk of Fire! Only an approved Hearth & Home Technologies surround may be used to cover inte- gral grills on solid fuel burning fireplaces. No other com- ponents such as shrouds, sheetmetal plates, etc., may be used to seal off vents.

WARNING! Risk of Explosion! Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.

WARNING! Risk of Explosion/Combustion Fumes! Connect vent sections per installation instructions.

•Connect exhaust vent pipe ONLY to exhaust starting collar and termination cap center collar.

•Connect inlet air vent ONLY to inlet air collar on appliance and the termination cap inlet air collar.

•DO NOT allow vent to sag below connection point to appliance.

E. Remote Control

If a remote control kit is used to control blower function, the Auxiliary 300 module can only be placed in the control cavity to the right of the control panel. See Figure 8.3.

AUXILIARY 300 MODULE

Figure 8.3 Location of AUX300 for Remote Control Blower Function

22

Heat & Glo • Cosmo-I30, Cosmo-I35 • 2239-900 Rev. H • 1/11

Page 21 Page 23
Image 22
Page 21 Page 23
Contents What to do if you smell gas Models Cosmo-I30 Cosmo-I35HOT Surfaces Congratulations Homeowner Reference InformationTable of Contents User GuideLimited Lifetime Warranty Limited Lifetime Warranty Listing and Code Approvals Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace IPI Battery Tray/Battery Installation Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Clear SpaceControl Module Operation Module ResetBefore Lighting Fireplace What to do if YOU Smell GAS Lighting Instructions IPIFinal inspection by GAS ValveIssue Solutions Frequently Asked QuestionsAfter Appliance is Lit Glass Cleaning Maintenance and ServiceMaintenance Tasks-Homeowner Remote ControlVenting Maintenance Tasks-Service TechnicianGasket Seal and Glass Assembly Inspection FireboxBurner Ignition and Operation IPI Pilot Flame PatternsGetting Started Typical Appliance SystemTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components TOP View Front View Side View Minimum Fireplace Size Fireplace Size RequirementsMinimum Fireplace Opening COSMO-I35 COSMO-I30Mantel and Wall Projections TOP ViewTermination Locations Vent Termination Minimum ClearancesInstallation Preparation Vent Limits Installing Vent Pipe and ApplianceConnecting Vent Pipe Venting ComponentsLocation of AUX300 for Remote Control Blower Function Placing, Securing and Leveling the Appli- anceFactory Built Wood Burning Installing Adaptor and Termination CapMasonry Damper Flashing Kit OptionalGas Pressure Gas InformationFuel Conversion Gas ConnectionON/OFF Switch Wiring RequirementsIntelliFire Plus Ignition System Wiring Electrical InformationOptional Accessories Requirements FAN BladesFan Wiring with Remote AUX 300 Module FAN WHT GRN BLK BlowersFinishing Clearances to Mantels or other Combustibles above ApplianceAppliance Setup Air Shutter Settings Air Shutter SettingCOSMO-I30 COSMO-I35 Symptom Possible Cause Corrective Action TroubleshootingIntelliFire Plus Ignition System Main burner will not Model Dimensions Appliance Dimension DiagramReference Materials Vent Kits Components Direct Vent Flex Liner KitsContact Information

Cosmo-130 specifications

The Heat & Glo LifeStyle Cosmo-130 is a modern gas fireplace that exemplifies innovation in heating design and functionality. This fireplace blends contemporary style with advanced technology, making it a perfect addition for any contemporary living space. Its sleek and minimalist design ensures that it not only serves as a heat source but also as a striking focal point in your home.

One of the main features of the Cosmo-130 is its impressive viewing area. The large glass front allows for an unobstructed view of the flames, creating an inviting ambiance. The design prioritizes aesthetics, with the fireplace being available in multiple configurations, including linear and traditional styles, enabling it to fit seamlessly into various interior designs.

With a focus on efficiency, the Cosmo-130 operates using an advanced gas burner system, which optimizes fuel use while producing substantial heat output. This fireplace boasts an impressive thermal efficiency rating, ensuring that heat is effectively distributed throughout the room while minimizing energy consumption.

The LifeStyle Cosmo-130 employs cutting-edge technology with its intuitive electronic controls. Homeowners can easily adjust the flame height and heat output to suit their preferences using a remote control or a smartphone app. This level of control contributes not only to comfort but also to energy efficiency, allowing users to personalize their heating experience.

Another notable aspect is the fireplace's customizable media options. Customers can choose from various decorative media, including logs, crystals, or stones, allowing for personalization to match different décor styles. This flexibility enhances the visual appeal of the fireplace and caters to individual tastes.

Safety is paramount in the design of the LifeStyle Cosmo-130. It includes features such as a thermostat that automatically maintains desired temperatures, as well as a safety shut-off system that activates should the unit overheat. This ensures peace of mind for users, especially in homes with children and pets.

With an emphasis on convenience and style, the Heat & Glo LifeStyle Cosmo-130 is an exceptional choice for those looking to enhance their home with a sophisticated heating solution. Its combination of aesthetic appeal, user-friendly technology, and efficient performance make it a standout option in the world of modern fireplaces, promising warmth and elegance in any setting.
Top Page Image Contents