Heat & Glo LifeStyle 6000TV-OAK-IPI owner manual Intermittent Pilot Ignition, Valve Assembly

Page 6

Service Parts	6000TV-OAK-IPI

(NG, LP) Exploded Parts Diagram	Beginning Manufacturing Date: 4-01
	Ending Manufacturing Date: ______

Intermittent Pilot Ignition	11
Valve Assembly	9
8	9
1	7
1	3
	4
	6
2	10
2
	5

ITEM		DESCRIPTION		SERIAL #	PART NO.
1	Flex Ball Valve Assembly				302-320A
2	ON/OFF Rocker Switch				060-521A

3	Valve NG				750-500

3	Valve LP				750-501

4	Flexible Gas Connector		PRE	002324021	477-301A
4	Flexible Gas Connector		POST 002324021		383-302A
			POST 002324021		383-302A
5	Module				593-592
6	Wire Assembly				593-590A
7	Burner Orifice NG (#40C)				582-840
7	Burner Orifice LP (#53C)				582-853
	Burner Orifice LP (#53C)				582-853
8	Pilot Assembly NG		PRE	002324021	385-510A
8	Pilot Assembly NG		POST 002324021		4021-025
			POST 002324021		4021-025
8	Pilot Assembly LP		PRE	002324021	385-511A
8	Pilot Assembly LP		POST 002324021		4021-026
			POST 002324021		4021-026
9	Pilot Bracket				385-164

10	Valve Bracket		PRE	002324021	550-169
10	Valve Bracket		POST 002324021		2025-101
			POST 002324021		2025-101
11	Ground Strap				2025-512
	3V Adaptor Plug				593-593A
	Battery Pack				593-594A
	72" & 80" Wire Assembly				522-504A

6	Heat & Glo • 6000TV-OAK, 6000TV-OAK-IPI • 384-900 Rev. N • 11/05

Image 6

Contents Installation and Operation What to do if you smell gasSafety and Warning Information Table of Contents Service Parts Log Set AssemblyService Parts List 6000TV-OAK, 6000TV-OAK-IPIValve Assembly Intermittent Pilot Ignition6000TV-OAK Standing Pilot Ignition1Approvals and Codes Installation CodesHigh Altitude Installations Appliance CertificationIntroducing the Heat & Glo Gas Fireplaces Pre-install Preparation2Getting Started ANY Such Action MAY Possibly Cause a Fire HazardDiagram of the 6000TV-OAK Locating the Fireplace 3Installing the FireplaceConstructing the Chase Clearance RequirementsFraming the Fireplace Framing DimensionsInstalling Optional Outside Make-up Air Negative Pressure Make-up AirRise to RUN Ratio = Installing the Vent System A. Vent System ApprovalsSystem Components Maximum NO. Of Elbows 2 90o or 4 45oGas Control Systems Vice Must be Wired to the Fireplace Junction BOXPositioning, Leveling, and Securing the Fireplace Roof PitchPressure Natural Gas Propane Gas Supply LineGas Pressure Requirements Standing PilotOptional Accessories Wiring the FireplaceFor Standing Pilot Ignition Wiring Appliance Requirements Wall SwitchFor Intermittent Pilot Ignition IPI Wiring Volt Transformer Operation using Battery PowerInstalling Trim, Logs and Ember Material FinishingBefore Lighting the Fireplace After the InstallationDouble-check for faulty components Lighting the FireplaceFireplace Maintenance 4Maintaining and Servicing Your FireplaceImportant Turn OFF the GAS Before Servicing Your Fireplace