Heat & Glo LifeStyle 6000TV-OAK-IPI 2Getting Started, Introducing the Heat & Glo Gas Fireplaces

Page 9

2Getting Started

Introducing the Heat & Glo Gas Fireplaces

Heat & Glo B-type vent gas fireplaces are designed to op- erate with all exhaust gases expelled to the outside of the building.

The information contained in this Installers Guide, unless noted otherwise, applies to all models and gas control systems. Gas fireplace diagrams, including the dimensions, are shown in this section.

Pre-install Preparation

This gas fireplace and its components are tested and safe when installed in accordance with this Installers Guide. Report to your dealer any parts damaged in shipment, particularly the condition of the glass. Do not install any unit with damaged, incomplete, or substitute parts.

The vent system components, gas logs and trim doors are shipped in separate packages. Log installation instructions are provided in the manual bag assembly shipped with the unit.

Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit. Failure to follow these instructions will void the owner’s warranty and may present a fire hazard.

The Heat & Glo Warranty will be voided by, and Heat & Glo disclaims any responsibility for, the following actions:

Installation of any damaged fireplace or vent system component.

Modification of the fireplace or direct vent system.

Installation other than as instructed by Heat & Glo.

Improper positioning of the gas logs or the glass door.

Installation and/or use of any component part not manu- factured and approved by Heat & Glo, not withstanding any independent testing laboratory or other party approval of such component part or accessory.

ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD.

When planning a fireplace installation, it’s necessary to determine:

Where the unit is to be installed.

The vent system configuration to be used.

Gas supply piping.

Electrical wiring.

Framing and finishing details.

Whether optional accessories—devices such as a fan, wall switch, or remote control—are desired.

If the fireplace is to be installed on carpeting or tile, or on any combustible material other than wood flooring, the fireplace should be installed on a metal or wood panel that extends the full width and depth of the fireplace.

Heat & Glo • 6000TV-OAK, 6000TV-OAK-IPI384-900 Rev. N • 11/05

9

Image 9
Contents What to do if you smell gas Installation and OperationSafety and Warning Information Table of Contents Log Set Assembly Service Parts6000TV-OAK, 6000TV-OAK-IPI Service Parts ListIntermittent Pilot Ignition Valve AssemblyStanding Pilot Ignition 6000TV-OAKHigh Altitude Installations Installation Codes1Approvals and Codes Appliance Certification2Getting Started Pre-install PreparationIntroducing the Heat & Glo Gas Fireplaces ANY Such Action MAY Possibly Cause a Fire HazardDiagram of the 6000TV-OAK Constructing the Chase 3Installing the FireplaceLocating the Fireplace Clearance RequirementsInstalling Optional Outside Make-up Air Framing DimensionsFraming the Fireplace Negative Pressure Make-up AirSystem Components Installing the Vent System A. Vent System ApprovalsRise to RUN Ratio = Maximum NO. Of Elbows 2 90o or 4 45oPositioning, Leveling, and Securing the Fireplace Vice Must be Wired to the Fireplace Junction BOXGas Control Systems Roof PitchGas Pressure Requirements Gas Supply LinePressure Natural Gas Propane Standing PilotFor Standing Pilot Ignition Wiring Appliance Requirements Wiring the FireplaceOptional Accessories Wall SwitchOperation using Battery Power For Intermittent Pilot Ignition IPI Wiring Volt TransformerFinishing Installing Trim, Logs and Ember MaterialDouble-check for faulty components After the InstallationBefore Lighting the Fireplace Lighting the FireplaceFireplace Maintenance 4Maintaining and Servicing Your FireplaceImportant Turn OFF the GAS Before Servicing Your Fireplace