Heat & Glo LifeStyle 36DV owner manual Appliance Setup

Page 35

12 Appliance Setup

A. Remove Shipping Materials

Remove shipping materials from inside or underneath the firebox.

B. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity.

C. Accessories

Install approved accessories per instructions included with accessories. See Service Parts List for appropriate accessories. Refer to Section 16.

WARNING

Shock or fire risk.

Use ONLY optional accessories approved for this appliance.

•Using non-listed accessories voids warranty.

•Using non-listed accessories may result in a safety hazard.

•Only Hearth & Home Technologies approved

accessories may be used safely.

D. Installing the Optional Heat-Zone-Gas Kit

1.Remove the knockout from the top of the appliance and discard it (see Figure 12.1).

2.Center the duct collar around the exposed hole and attach it to the appliance with 3 screws. Note: Do this BEFORE final positioning of the appliance.

3.Determine the location for the air register/fan housing assembly.

Reference the Heat-Zone-Gas kit instructions for the remaining installations steps.

HEAT-ZONE-GAS

KNOCKOUTS

Figure 12.1

E. Ember Placement

WARNING

Explosion Risk.

•Follow ember placement instructions in manual.

•Do NOT place embers directly over burner ports.

•Replace ember material annually.

Improperly placed embers interferes with proper burner operation.

Placing the Ember Material

Ember material is shipped with this gas appliance. To place the ember material:

•Remove the ash lip (see Figure 12.2) that is located in front of the glass.

Figure 12.2. Ash Lip

•Remove the side panels located in front of the glass.

•Remove the pull mesh firescreen by unhooking from the appliance.

•Pull and release the four glass latches (2 per side) located on the sides of the glass frame.

•Grasping the upper lip with one hand and the lower lip with the other, pull the bottom of the glass out first. Guide the bottom while letting the top drop down under the top of the opening.

•There are two types of ember shipped with the unit. Embers for the burner surface and Mystic Embers for the floor of the unit.

•Do NOT place embers between log #3 and log #4. They may disrupt the flames and are not visible.

•Place Mystic Embers on the floor of unit. Use Mystic Embers to hide the pilot wires on left side of the burner.

•Save the remaining ember materials for use during appliance servicing.

•Replace glass firescreen and door front trim on the unit.

Heat & Glo • Escape-36DV • 2012-900 • Rev. AA • 04-08

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Hot glass will cause burns Model Escape-36DVWhat to do if you smell gas Homeowner Reference Information CongratulationsTable of Contents Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide DetectorsTools and Supplies Needed Installation to ensure maximum safety and benefitGetting Started Selecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseHearth Extension Mantel ProjectionsSee .4 for specific clearances Termination LocationsVent Termination Minimum Clearances Alcove Applications Measuring Standards Vent Information and DiagramsVent Table Key Use of ElbowsMinimum Maximum Vent DiagramsTop Vent Horizontal Termination One Elbow Two ElbowsV1 + V2 Minimum Maximum Top Vent Horizontal Termination Three ElbowsFlue Restrictor Instructions Top Vent Vertical Termination No Elbow V1 = 40 ft. Max .2 m+ V 2 Minimum Maximum V1 + V2 Minimum H1 + H2 Maximum Top Vent Vertical Termination Three ElbowsCombustible Wall Penetration Vent Clearances and FramingPipe Clearances to Combustibles Wall Penetration FramingVertical Penetration Framing Installing the Ceiling FirestopInstalling Attic Shield Securing and Leveling the Appliance Removing Non-combustible Facing Mate- rial AssemblyAppliance Preparation Attaching Non-combustible Facing Material Installing Non-combustible Facing MaterialAssembling Pipe Sections Installing Vent PipeAssembly of Vent Sections DVP Pipe Attaching Vent to the Firebox AssemblyAssembling DVP-12A Slip Sections Assembling Minimum Installations MI SectionsHorizontal Sections Disassembly of Vent SectionsSecuring the Vent Sections Vertical Sections Heat Shield Requirements for Horizontal Termination Installing Heat Shield and Horizontal Termination CapInstalling the Horizontal Termination Cap Roof Pitch Min. Ft Installing Roof Flashing and Vertical Termination Cap17 Assembling the Storm Collar Around the Pipe Assembling and Installing Storm CollarPressure Natural Gas Propane Gas InformationFuel Conversions Gas Connection Gas PressuresHigh Altitude Installations Electrical Information Recommendation for WireConnecting to the Appliance Intellifire Ignition System WiringDetail a Romex Connector Junction Box InstallationFacing Material FinishingFinishing Requirements Appliance Setup LOG #1 SRV750-706 TWO Positioning the LogsStep LOG #4 SRV2012-162 LOG #2 SRV569-705LOG #3 SRV2012-161 LOG #7 SRV2012-165 LOG #5 SRV2012-163LOG #6 SRV2012-164 Final Step LOG #8 SRV2012-166Replacing Glass Assembly Glass AssemblyAir Shutter Setting Removing Glass AssemblyBefore Lighting Appliance Operating InstructionsFinal inspection by Turn off all electric power to the applianceOn position. The ON/OFF switch may Lighting Appliance IPI IgnitionAfter Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Sympton Possible Cause Corrective Action TroubleshootingIntellifire Ignition System Symptom Possible Cause Corrective Action Maintaining and Servicing Appliance Maintenance TasksReplacing Light Bulb Doors, Surrounds Inspect Maintenance TasksLocation Inches Millimeters Appliance Dimension DiagramReference Materials DVP vent components Vent Components DiagramsHorizontal Termination Cap Kit Horizontal Termination Cap Wall Shield FirestopHeat Shield Cap Shield Flashing 13-7/8 352 mm 241 mm 787 mm 13-1/4 367 mm 24-5/8 625 mm 27-1/2 127 mmRoof Flashing Multi-pak 13-3/4 11-7/8 349 mm 127 mm 302 mm 13-3/4 13-7/8 352 mm 349 mmDVP-TVHW Ending Manufacturing Date Service PartsLog Set Assembly Beginning Manufacturing Date SeptAt Depot Service Parts ListStocked Be ordered from an authorized dealer Limited Lifetime Warranty Heat & GLO GAS Appliance Products Limited Lifetime WarrantyContact Information
Related manuals
Manual 26 pages 27.68 Kb

36DV specifications

The Heat & Glo LifeStyle 36DV is a state-of-the-art gas fireplace designed for modern living spaces. This model stands out for its seamless blend of aesthetics, performance, and efficiency. With its sleek design and innovative technologies, the LifeStyle 36DV redefines how people experience warmth and ambiance in their homes.

One of the standout features of the LifeStyle 36DV is its powerful heating capability. This direct vent gas fireplace efficiently circulates warm air throughout the room while maintaining optimal energy usage. With an impressive heating output, it can effectively warm spaces of varying sizes, making it suitable for both large living areas and cozy nooks.

The LifeStyle 36DV is engineered with advanced gas technology. The fireplace utilizes a unique ignition system that ensures reliable starts and consistent performance. This system not only enhances ease of use but also increases safety, minimizing any risks associated with traditional ignition methods.

Additionally, the fireplace is equipped with a dynamic, glass-front design that maximizes the viewing area of the flames. With a variety of media options available, including traditional logs and modern glass media, homeowners can customize the look and feel of their fireplace to match their unique style. The LifeStyle 36DV can serve as a focal point in any room, providing both warmth and visual appeal.

Another noteworthy characteristic of the LifeStyle 36DV is its intuitive control system. With the ability to operate via remote control, wall switch, or smartphone app, adjusting the fireplace's settings has never been easier. Users can effortlessly change the flame height, control fan speed, and set timers, allowing for a personalized experience tailored to individual preferences.

The energy efficiency of the LifeStyle 36DV also cannot be overlooked. This fireplace is designed to meet stringent environmental standards, providing homeowners with a cost-effective heating solution that doesn't compromise on style. By utilizing innovative insulation and venting technology, the LifeStyle 36DV keeps the warmth inside where it belongs.

In summary, the Heat & Glo LifeStyle 36DV is a remarkable gas fireplace offering a perfect combination of modern technology and traditional warmth. With its stylish design, powerful heating capabilities, customizable aesthetics, and user-friendly controls, it stands out as a premier choice for homeowners looking to enhance their living spaces. Whether for cozy family gatherings or romantic evenings, the LifeStyle 36DV provides an inviting atmosphere that is hard to match.
Top Page Image Contents