Heart & Home Collectables MHR36, MHC36 Position the Hearth Extension, Finishing Material, Mantel

Page 21

MHC36 AND MHR36 INSTALLATION INSTRUCTIONS

15.Position the Hearth Extension

Position and secure the hearth extension over the protective metal strips that have been placed partially under the fireplace front. These strips should be protruding approximately 2 in. from under the fireplace front and 2 in. on both sides of the fireplace opening. Seal the crack between the hearth extension and fireplace with a bead of noncombustible sealant. See Figure 21. Apply a noncombustible finishing material of your choice to the hearth extension.

Figure 21 - Position the Hearth Extension

16.Finishing Material

Do not install combustible materials over the black face of the fireplace! This poses a safety hazard and may start a fire. You may only use noncombustible material over the black face of the fireplace.

a.Combustible Material

Material which is made of or surfaced with wood, compressed paper, plant fibers, plastics, or any material capable of igniting and burning, whether flame proofed or not, plastered or unplastered.

b.Noncombustible Material

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

c.Noncombustible Sealant Material

Sealants which will not ignite and burn; General Electric RTV103 Black (or equivalent), Rutland, Inc. Fireplace Mortar #63 (or equivalent).

After completing the framing and applying the facing material (dry wall) over the framing, a 1/2 in. wide (maximum) bead of noncombustible sealant must be used to close off any gaps at the top and sides between the fireplace and facing to prevent cold air leaks.

Only noncombustible materials may be used to cover the black metal fireplace front.

17.Mantel

A combustible mantel may be positioned no lower than 12 in. above the top of the fireplace opening. The combustible mantel may have a maximum depth of 12 in. Combustible trim pieces that project no more than 1-1/2 in. from the face of the fireplace can be placed no closer than 6 in. from the top of the fireplace opening. Combustible trim must not cover the black metal surfaces of the fireplace. This mantel clearance is in accordance with Section 7-3.3.3 of ANSI/ NFPA211.

18.Glass Doors

This fireplace has been tested and listed for use with doors as specified in Section “C. Fireplace System Components”. Please refer to the manual packed with each set of doors for installation instructions.

08/04

31072 Rev G

21

Image 21
Contents Installation & Operating Instructions Table of Contents Design and Installation Considerations Description of the Fireplace System Listings and Code ApprovalsHeatilator fireplace system consists of the following Optional Components IncludeFireplace Components System ComponentsAS8 Chimney ComponentsAS8 Fireplace Locations and Space Requirements PRE-INSTALLATION PreparationMHC36 and MHR36 Installation Instructions Framing the Fireplace Frame the FireplaceSidewalls/Surrounds Chimney RequirementsOffset Chart Using Offsets and ReturnsNumber of Sections Required Chimney Height Requirements above roof linePosition the Fireplace Fireplace InstallationPlace the Protective Metal Hearth Strips Level the FireplaceAssemble Chimney Sections Install the Firestop SpacersDouble-check the Chimney Assembly Attic Insulation ShieldSecure the Chimney System See Figures 14 MH842 Ceiling/Roof ThimbleTermination Cap Install the Outside Air KitGas Log/Lighter Provisions Complete the EnclosureField Constructed Hearth Extension Hearth ExtensionFinishing Material Position the Hearth ExtensionMantel Glass DoorsOperating Instructions General Information Outside AirFlue Damper Grate FirescreenWood Fuel Starting a Fire Draft ProblemsFlue Draft Chimney Cleaning Maintenance InstructionsDisposal of Ashes Creosote and SootIndex Replacement Parts Advantage Limited WarrantyHow to Obtain Service Heatilator Woodburning Fireplace