Desa (V)T32EN Removing/Replacing Glass Door, Removing Louver Panels, Removing Glass Door

Page 19

Fireplace Installation

Continued

Removing/Replacing Glass Door

CAUTION: Do not operate this fireplace with a bro- ken glass door panel or without the glass door panel securely in place. For replacement part information see Replacement Parts, page 28.

CAUTION: Wear gloves and safety glasses while handling or removing broken glass. Do not remove if glass is hot. Keep children and pets away from glass.

WARNING: If fireplace has been running, turn off and unplug fireplace. Let cool before removing glass door or louvers.

Removing Louver Panels

Remove the top and bottom louver panels by simultaneously pulling both top end spring latches towards the center of the appliance until they are disengaged from the locating holes (see Figure 36). Repeat for bottom spring latches and pull the louvers outward. To install or replace items removed, simply reverse the procedures above.

Spring Latch

Louver Panel

Figure 36 - Removing Louver Panel

Removing Glass Door

If replacement of glass is necessary, the entire assembly, glass and frame, must be replaced. If glass is broken, wear gloves and tape the remaining fragments onto the frame.

1.Remove screen assembly by pushing the rod either left or right and then down and forward to remove screen/rod assembly from the firebox. Set assembly aside.

2.Lift up on latches to unlock. There are two on top of firebox and two below firebox that hold glass door in place (see Figure 37).

3.While holding glass door to prevent it from falling and causing injury, remove the five screws from the hinge located on the left side of door frame assembly (see Figure 37).

4.Remount the new frame at the hinge with five new screws before closing door. This will ensure seating of the gasket.

5.Close glass door frame. Lock latches by placing the bar under the tab on door and pushing down and back on latch (see Figure 37).

6.Replace screen/rod assembly by reversing step 1.

7.Replace louvers by reversing procedure under Removing Lou- ver Panels.

Unlock Lock

Latch

Hinge

Screw

Glass

Frame

Assembly

Figure 37 - Removing/Replacing Glass Door

Cleaning Glass Door

See Cleaning and Maintenance on page 25.

Installing Optional Brick liner Models BL32D, BL36D(S), BL36DH(S)

WARNING: If fireplace has been running, turn off and

unplug fireplace. Let cool before installing brick liner.

This brick liner kit is optional. You may purchase brick liner from your local retailer or see Accessories, page 29.

CAUTION: Always handle brick panels with two hands. Do not force brick panels into place. Excessive force will break brick panels.

1.Remove top and bottom louvers to allow access to door latches.

2.Unlock door latches and open glass door. See steps 1 and 2 of

Removing/Replacing Glass Door.

3.If installing brick liner in new fireplace, go to step 4. If install- ing brick liner in an existing fireplace, carefully remove logs, lava rock, and ember material.

4.Remove three screws from deflector shield on the inside top of firebox. Set shield and screws aside.

108860-01D

www.desatech.com

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents What to do if YOU Smell GAS For Your SafetySafety Information Table of ContentsProduct Identification Product FeaturesLocal Codes Location and space requirements Pre-Installation PreparationClearances Framing and finishing Framing Clearances for Installation Against an Exterior WallTermination CAP AIR Supply Inlet GAS Meter Location of Termination CapHorizontal Termination Installation Venting Installation InstructionsInstallation Precautions Installation PlanningVent Pipe Connections Installing Siding Standoff Square Termination Horizontal Termination ConfigurationsVenting with Two 90 Elbows Snorkel Termination InstallationOffset with Wall Strap and 45 Elbows Flat Ceiling InstallationVertical Venting Vertical Termination ConfigurationsInstalling optional blower accessories Fireplace InstallationHigh Altitude Installation Parts lists for venting kits and componentsBlower Model BK Model BKT InstallationBlower Wiring Diagram Installing Gas Piping to Fireplace LocationInstallation Items Needed Installation Items Needed Connecting Fireplace to GAS SupplyTest Pressures In Excess Of 1/2 Psig 3.5 kPa Pressure Testing Gas Supply Piping SystemPressure Testing Fireplace Gas Connections Checking GAS ConnectionsRemoving Louver Panels Cleaning Glass DoorUnplug fireplace. Let cool before installing brick liner Removing/Replacing Glass DoorInstalling Log No Installing logs, lava rock and glowing embersInstalling Logs No and No Wall Switch Installation Wiring DiagramOptional Remote control Installation model WRC To Turn OFF GAS To Appliance For your safety read Before lightingOperating Fireplace Lighting InstructionsBurner Flame Pattern Operating optional Blower accessoryPilot assembly Inspecting BurnersLogs Cleaning MaintenanceGlass Door Pilot and burnersTo clean pilot. This can damage pilot unit TroubleshootingTop above Gas leak. See Warning statement atSpecifications Replacement PartsService Hints Technical ServiceAccessories Illustrated Parts Breakdown VT32EPRB Parts List109 Parts List 23-5 23-3 23-4 23-2 23-1 VT36ENR 109 2917 KEY Description Keep this Warrant Warranty Information

(V)T32EN specifications

Desa (V)T32EN is a cutting-edge vehicle designed to meet the growing demands of modern transportation while ensuring efficiency, safety, and sustainability. This remarkable vehicle is the embodiment of innovative engineering and advanced technology, making it a key player in both the commercial and personal vehicle sectors.

One of the standout features of the Desa (V)T32EN is its powerful and efficient powertrain. The vehicle is equipped with a state-of-the-art engine that incorporates hybrid technology, allowing it to seamlessly switch between electric and gasoline modes. This flexibility not only helps reduce emissions but also provides impressive fuel efficiency, making it ideal for long-distance travel or urban commuting. The hybrid system is complemented by regenerative braking, which captures energy during braking and feeds it back into the vehicle’s battery, enhancing overall efficiency.

Another significant characteristic of the Desa (V)T32EN is its advanced safety features. The vehicle is designed with a robust safety framework that includes a suite of sensors and cameras for 360-degree awareness. This technology enables features such as automatic emergency braking, lane departure warning, and adaptive cruise control, ensuring a safer driving experience for both the driver and passengers. Additionally, the vehicle includes a reinforced chassis that meets high safety standards, providing peace of mind on the road.

In terms of comfort and convenience, the Desa (V)T32EN excels with its spacious interior and modern infotainment system. The cabin is thoughtfully designed, providing ample legroom and storage options. The infotainment system features a large touchscreen display that integrates seamlessly with smartphones, allowing for hands-free operation of navigation, music, and communication apps. Furthermore, climate control and adjustable seating settings enhance the overall driving experience, making long journeys enjoyable.

Technological sophistication extends to the vehicle’s connectivity features. The Desa (V)T32EN boasts advanced connectivity options that allow for real-time updates on traffic, weather, and vehicle performance. With built-in Wi-Fi and mobile app integration, users can stay connected to the digital world while on the move.

In conclusion, the Desa (V)T32EN is not just a vehicle; it represents the future of transportation. Its combination of hybrid technology, advanced safety features, and user-friendly connectivity makes it a formidable contender in the automotive landscape. As consumers increasingly prioritize sustainability and safety, the Desa (V)T32EN stands out as a leading option that aligns with these values, ensuring it meets the diverse needs of today’s drivers.
Top Page Image Contents