Desa (V)T32EN installation manual Vent Pipe Connections

Page 8

Venting Installation

instructions

Continued

2.Direct vent pipe sections and components are designed with special twist-lock connections.

Twist-Lock Procedure: The female ends of the pipes have locking lugs (indentations). These lugs will slide straight into matching slots on the male ends of adjacent pipes. Push pipe sections together and twist one section clockwise approxi- mately one-quarter turn until the sections are fully locked (see Figure 8). Note: Horizontal runs of vent must be supported every three feet. Use wall straps for this purpose.

3.Use a 45° elbow to connect venting system to fireplace flue collar. The elbow is designed to be twist-locked onto the flue collar as described in step 2. IMPORTANT: Do not attempt to alter the configuration of the elbow by cutting, twisting, bending, etc.

4.Assemble the desired combination of pipe and elbows to the fireplace. If there are long portions of venting run, pre-as- sembled pipe sections may be installed as subassemblies for convenience.

5.Carefully determine the location where the vent pipe assembly will penetrate the outside wall. The center of the hole should line up with the center-line of the horizontal vent pipe. Mark the wall for a 10" x 10" square hole. Cut and frame the square hole in the exterior wall where the vent will be terminated. If the wall being penetrated is constructed of noncombustible material, such as masonry block or concrete, a 7 3/4" hole with zero clearance is acceptable (see Figure 9).

WARNING: Do not recess vent termination into any wall. This will cause a fire hazard.

6.Noncombustible Exterior Wall: Position the horizontal vent cap in the center of the 7 3/4" round hole and attach to the exterior wall with four wood screws provided. Before attach- ing the vent cap to exterior wall, run a bead of non-hardening mastic (pliable sealant) around the outside edges to make a seal between it and the outside wall. Note: The four wood screws provided should be replaced with appropriate fasteners for stucco, brick, concrete, or other types of sidings.

Combustible Exterior Wall: For vinyl siding, stucco, or wood exteriors, a siding standoff must be installed between the vent cap and exterior wall. The siding standoff prevents excessive heat from damaging the siding materials. Siding material must be cut to accommodate standoff. Bolt the vent cap to the standoff. Apply non-hardening mastic around outside edge of standoff. Position the standoff/cap assembly in the center of the 10" square hole and attach to exterior wall with wood screws provided (see Figure 11, page 9). The siding standoff must sit flush against the exterior fascia material.

Female

Locking Lugs

Male

Slots

Figure 8 - Vent Pipe Connections

Vent Opening

Combustible Wall 10" Inside Framing

10"(254 mm) (254 mm)

10"

 

(254 mm)

 

 

(Framing

Vent Opening

Detail)

 

Noncombustible Wall

 

7 3/4"

 

(197 mm)

Center

 

of Hole

Figure 9 - Vent Opening Requirements

Apply Mastic to

All Four Sides

Vent Cap

Wood Screw

Figure 10 - Installing Horizontal Vent Cap

www.desatech.com

108860-01D

Page 7 Page 9
Image 8
Page 7 Page 9
Contents For Your Safety What to do if YOU Smell GASTable of Contents Safety InformationLocal Codes Product FeaturesProduct Identification Clearances Pre-Installation PreparationLocation and space requirements Framing Clearances for Installation Against an Exterior Wall Framing and finishingLocation of Termination Cap Termination CAP AIR Supply Inlet GAS MeterVenting Installation Instructions Installation PrecautionsInstallation Planning Horizontal Termination InstallationVent Pipe Connections Installing Siding Standoff Horizontal Termination Configurations Square TerminationSnorkel Termination Installation Venting with Two 90 ElbowsFlat Ceiling Installation Offset with Wall Strap and 45 ElbowsVertical Termination Configurations Vertical VentingFireplace Installation High Altitude InstallationParts lists for venting kits and components Installing optional blower accessoriesModel BKT Installation Blower Model BKInstallation Items Needed Installing Gas Piping to Fireplace LocationBlower Wiring Diagram Connecting Fireplace to GAS Supply Installation Items NeededPressure Testing Gas Supply Piping System Pressure Testing Fireplace Gas ConnectionsChecking GAS Connections Test Pressures In Excess Of 1/2 Psig 3.5 kPaCleaning Glass Door Unplug fireplace. Let cool before installing brick linerRemoving/Replacing Glass Door Removing Louver PanelsInstalling logs, lava rock and glowing embers Installing Log NoInstalling Logs No and No Optional Remote control Installation model WRC Wiring DiagramWall Switch Installation For your safety read Before lighting Operating FireplaceLighting Instructions To Turn OFF GAS To ApplianceOperating optional Blower accessory Pilot assemblyInspecting Burners Burner Flame PatternCleaning Maintenance Glass DoorPilot and burners LogsTroubleshooting To clean pilot. This can damage pilot unitGas leak. See Warning statement at Top aboveReplacement Parts Service HintsTechnical Service SpecificationsAccessories Illustrated Parts Breakdown Parts List VT32EPRB109 Parts List 23-5 23-3 23-4 23-2 23-1 VT36ENR 109 2917 KEY Description Warranty Information Keep this Warrant

(V)T32EN specifications

Desa (V)T32EN is a cutting-edge vehicle designed to meet the growing demands of modern transportation while ensuring efficiency, safety, and sustainability. This remarkable vehicle is the embodiment of innovative engineering and advanced technology, making it a key player in both the commercial and personal vehicle sectors.

One of the standout features of the Desa (V)T32EN is its powerful and efficient powertrain. The vehicle is equipped with a state-of-the-art engine that incorporates hybrid technology, allowing it to seamlessly switch between electric and gasoline modes. This flexibility not only helps reduce emissions but also provides impressive fuel efficiency, making it ideal for long-distance travel or urban commuting. The hybrid system is complemented by regenerative braking, which captures energy during braking and feeds it back into the vehicle’s battery, enhancing overall efficiency.

Another significant characteristic of the Desa (V)T32EN is its advanced safety features. The vehicle is designed with a robust safety framework that includes a suite of sensors and cameras for 360-degree awareness. This technology enables features such as automatic emergency braking, lane departure warning, and adaptive cruise control, ensuring a safer driving experience for both the driver and passengers. Additionally, the vehicle includes a reinforced chassis that meets high safety standards, providing peace of mind on the road.

In terms of comfort and convenience, the Desa (V)T32EN excels with its spacious interior and modern infotainment system. The cabin is thoughtfully designed, providing ample legroom and storage options. The infotainment system features a large touchscreen display that integrates seamlessly with smartphones, allowing for hands-free operation of navigation, music, and communication apps. Furthermore, climate control and adjustable seating settings enhance the overall driving experience, making long journeys enjoyable.

Technological sophistication extends to the vehicle’s connectivity features. The Desa (V)T32EN boasts advanced connectivity options that allow for real-time updates on traffic, weather, and vehicle performance. With built-in Wi-Fi and mobile app integration, users can stay connected to the digital world while on the move.

In conclusion, the Desa (V)T32EN is not just a vehicle; it represents the future of transportation. Its combination of hybrid technology, advanced safety features, and user-friendly connectivity makes it a formidable contender in the automotive landscape. As consumers increasingly prioritize sustainability and safety, the Desa (V)T32EN stands out as a leading option that aligns with these values, ensuring it meets the diverse needs of today’s drivers.
Top Page Image Contents