Desa VSGF33PRB, EFS33NRB, EFS33PRB, VSGF33NRB Conventional Fireplace Installation, Access Hole

Page 10

INSTALLATION

Continued

CONVENTIONAL FIREPLACE INSTALLATION

Conventional installation of this fireplace involves installing fireplace along with the corner, face, or cabinet mantel with hearth base accessories against a wall in your home. Follow the instructions in this section to install the fireplace in this manner. Note: The instructions in this section show instal- lation using the cabinet mantel and the G3333F/G3334U/G3004W/G3335F/G3007U se- ries hearth base accessories. The hearth base ac- cessory shown is optional for this installation. You can install fireplace and cabinet/corner mantel di- rectly on the floor. The corner mantel accessory cannot be installed with the G3333F/G3334U/ G3004W/G3335F/G3007U hearth base. The cor- ner mantel can be paired with the G3008F/ G3009U/G3010F corner hearth base. If mounting fireplace and cabinet or corner mantel to the floor, an optional G3005J/3005S/3005B Slim Base kit may be installed.

1.Assemble cabinet mantel, hearth base, and trim accessories. Assembly instructions are in- cluded with each accessory.

2.When installing blower, install a properly grounded, 120 volt three-prong electrical out- let at fireplace location if an outlet is not there. If possible, locate outlet so cabinet mantel will cover it when installed (see Figure 9).

3.Install gas piping to fireplace location. This installation includes an approved flexible gas line (if allowed by local codes) after the equip- ment shutoff valve. The flexible gas line must be the last item installed on the gas piping. See Installing Gas Piping to Fireplace Loca- tion, pages 12 and 13.

Electrical Outlet

Rigid Pipe and Gas

Shutoff Valve

Hearth Base

Gas Line

Access Hole

 

Figure 9 - Placing Hearth Base

Accessory Against Wall

4.Place hearth base accessory against wall at installation location. Cut an access hole in hearth top to run flexible gas line to fireplace (see Figure 9). Make sure to locate access hole so cabinet mantel will cover it when installed. Note: You can secure base to floor using wood screws. Countersink screw heads and putty over.

5.Route flexible gas line through access hole in hearth base.

6.Center cabinet mantel on hearth base (see Fig- ure 10). Make sure mantel is flush against wall.

7.Break off nailing flanges (see Figure 11) with hammer or pliers.

8.Place cardboard or other protective material on top of hearth base. Carefully set fireplace on protective material, with back of fireplace inside mantel opening.

9.Attach flexible gas line from fireplace gas regulator to gas supply. See Connecting Fire- place to Gas Supply, page 14.

10.If blower is installed, route blower electrical cord through access holes in either side of fire- place. Note: Bushing may be moved if neces- sary. Plug electrical cord into electrical outlet.

Cabinet

Mantel

Figure 10 - Installing Cabinet Mantel

Nailing

Flanges

Figure 11 - Location of Nailing Flanges

10

www.desatech.com

113132-01A

Image 10
Contents What to do if YOU Smell GAS Table of Contents Safety Information Log Base Assembly VSGF33NRB Shown Product IdentificationUnpacking Product FeaturesLocal Codes AIR for Combustion VentilationUnusually Tight Construction Providing Adequate VentilationDetermining FRESH-AIR Flow for Fireplace Location Confined and Unconfined SpaceVentilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Check GAS Type InstallationInstalling Hood Electrical HookupInstallation Clearances TopConventional Fireplace Installation Access HoleFront Width BUILT-IN Fireplace InstallationActual Framing Height DepthMantel Clearances for Built-In Installation Installing GAS Piping to Fireplace LocationInstallation Items Needed Propane/LP Gas ConnectionConnecting Fireplace to GAS Supply Hex socket wrench or nut-driver Phillips screwdriverPressure Testing Fireplace Gas Connections Pressure Testing Gas Supply Piping SystemChecking GAS Connections Damage or personal injury Lighting For Your Safety Read Before LightingOperating Fireplace InstructionsOptional HAND-HELD Remote Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance Shutting Off HeaterON/OFF Model Ghrcb Thermostat Model GhrctbPilot Flame Pattern Inspecting BurnersOptional Blower Operation Main BurnerCleaning Maintenance Burner Injector Holder and Pilot AIR Inlet HoleSpecifications Wiring DiagramLogs Troubleshooting Observed Problem Possible Cause RemedyDiagram, Ventilation requirements Statement on Gas leak. See WarningGas leak. See Warning statement on Technical Service Replacement PartsService Hints Parts Under WarrantyIllustrated Parts Breakdown Parts List Fireplace Models EFS33NRB, VSGF33NRB, EFS33PRB and VSGF33PRB Parts Available not Shown Accessories Cabinet Mantel and Full Hearth Base Laminate Trim for Hearth or MantelReceiver and HAND-HELD Remote Control KIT Ghrcb Receiver and HAND-HELD Thermostat Remote Control KIT GhrctbFirebox Brick Liner G8005 113132-01A Keep this Warranty Warranty InformationLimited Warranty VENT-FREE GAS Fireplace

VSGF33PRB, EFS33PRB, VSGF33NRB, EFS33NRB specifications

Desa EFS33PRB, VSGF33PRB, EFS33NRB, and VSGF33NRB are four highly regarded heating appliances known for their efficient performance and user-friendly features. Each of these models offers a unique set of characteristics, making them suitable for different heating needs and preferences.

The Desa EFS33PRB is a prominent model designed with energy efficiency in mind. It utilizes advanced combustion technology that maximizes heat output while reducing fuel consumption. This model features a sleek, modern design complemented by a user-friendly control panel. The adjustable thermostat allows users to set their desired temperature easily, ensuring comfort throughout the space. Additionally, the EFS33PRB is equipped with an automatic shut-off mechanism for enhanced safety, providing peace of mind during usage.

On the other hand, the VSGF33PRB stands out with its high-velocity fan that ensures rapid and even heat distribution across larger areas. This model features a robust build quality and is designed to operate quietly, making it an excellent option for residential spaces where noise levels must be kept to a minimum. The VSGF33PRB also incorporates a range of settings for different heating needs, allowing users to customize their heating experience.

Moving to the EFS33NRB model, it emphasizes versatility with its multi-fuel capability. This appliance can efficiently utilize various fuel types, making it suitable for different environments and preferences. The EFS33NRB is designed with user convenience in mind, featuring easy maintenance capabilities, such as a removable ash pan for hassle-free cleaning. It also includes an electronic ignition system, ensuring quick and reliable startup every time.

Lastly, the VSGF33NRB shares many characteristics with its counterparts but enhances its appeal with an increased focus on eco-friendliness. This model is crafted to produce lower emissions, contributing positively to environmental sustainability. It boasts a high-efficiency rating, thus not only providing effective heating solutions but also reducing energy bills.

In summary, the Desa EFS33PRB, VSGF33PRB, EFS33NRB, and VSGF33NRB collectively represent a complete range of heating options suitable for various applications. Their dedication to efficiency, safety, and user convenience makes them desirable choices for consumers seeking reliable and innovative heating solutions. Whether it be through advanced technology, enhanced safety features, or eco-friendly capabilities, these models stand out in the competitive market of heating appliances.