Desa FMH26TN 14 Optional Mantel Installation, Mantel Clearances for Built-InInstallation

Page 10
Mantel Clearances for Built-In Installation

NATURAL GAS VENT-FREE FIREPLACE SYSTEM

INSTALLATION

Continued

Mantel Clearances for Built-In Installation

If placing mantel above built-in fireplace, you must meet minimum clearance between mantel shelf and top of fireplace opening.

NOTICE: Surface temperatures of adjacent walls and mantels be- come hot during operation. Walls and mantels above the firebox may become hot to the touch. If installed properly, these tempera- tures meet the requirement of the national product standard. Fol- low all minimum clearances shown in this manual.

NOTICE: If your installation does not meet the minimum clearances shown, you must do one of the following:

raise the mantel to an accept- able height

remove the mantel

OPTIONAL MANTEL

INSTALLATION

Note: Refer to instructions provided with the mantel for assembly instructions. Refer to instructions below for system installa- tion. Refer to instructions on page 4 for firebox assembly. Blower accessory should be installed if it is being used (see Accesso- ries, page 26).

1.Unscrew four brass screws that attach top louver to fireplace. Remove louver from fireplace and set aside.

2.Place fireplace on wood base.

3.Place mantel around fireplace/base assembly.

4.Assemble brass trim kit. See Assem- bling Brass Trim, page 11.

5.Firmly snap brass trim kit on shoulder screws. Shoulder screws are located on fireplace cabinet (see Figure 13).

6.Align brass trim kit for flush fit around opening.

7.Use two 3" wood screws provided and attach fireplace base to wooden base (see Figure 13).

8.Remove brass trim kit and mantel. Be careful not to damage wall or mantel.

9.Place wood base next to wall at instal- lation location.

10.Attach wood base to floor with two 1 3/4" black screws provided (see Figure 14). If the floor is concrete use anchor method (see Attaching Wood Base to Solid Floor, page 14).

11.Install gas line. See Connecting To Gas Supply, page 14.

Mantel Shelf

Note:

10"

 

 

 

8"

 

 

 

All vertical

 

 

 

measurements

6"

 

 

 

 

 

 

are from top of

 

 

 

2 1/2"

 

 

 

fireplace

 

 

 

opening to

 

 

 

 

bottom of

 

 

 

 

mantel shelf. All

 

 

 

 

measurements

 

 

 

 

are in inches.

 

 

 

 

Side of

13"

16"

19"

21"

 

 

 

 

Firebox

 

 

 

 

 

 

 

 

Figure 12 - Minimum Mantel Clearances for Built-In Installation

12.Check for leaks. See Checking Gas Connections, page 16.

13.Place mantel around fireplace. Be care- ful not to damage wall or mantel.

14.Place brass trim kit on the shoulder screws located on the side and top of the fireplace. Firmly snap the brass trim over the shoulder screws on fireplace (see Figure 13).

15.Adjust assembly to remove any gaps. Attach remaining two 3" wood screws from hardware pack through openings inside of fireplace sides into the man- tel. The openings are located at top be- hind the area for the black louvers (see Figure 13).

16.Reinstall top black louvers.

Hole for 3"

 

wood screw

Shoulder

for attaching

fireplace to

Screws

mantel

 

 

Hole for 3"

Assembled

wood screw

for attaching

Brass Trim

fireplace to

 

wooden base

Figure 13 - Attaching Brass Trim to Fireplace

1 3/4" Screw

Wood Base

Figure 14 - Attaching Wood Base to Floor

10

107105

Image 10
Contents Do not try to light any appliance VENT-FREENATURAL GAS FIREPLACE SYSTEMWHAT TO DO IF YOU SMELL GAS OWNER’S OPERATION AND INSTALLATION MANUALNATURAL GAS VENT-FREEFIREPLACE SYSTEM SAFETY INFORMATIONWARNINGS LOCAL CODES PRODUCT FEATURESSAFETY PILOT UNPACKINGcessories, page 26. Install optional ASSEMBLYInstalling Log blower now. Follow installation inUnusually Tight Construction AIR FOR COMBUSTION AND VENTILATIONPROVIDING ADEQUATE VENTILATION Confined and Unconfined SpaceAIR FOR COMBUSTION AND VENTILATION DETERMINING FRESH-AIRFLOW FOR FIREPLACE LOCATIONNATURAL GAS VENT-FREEFIREPLACE SYSTEM ContinuedVentilation Air From Outdoors VENTILATION AIRVentilation Air From Inside Building AIR FOR COMBUSTION AND VENTILATIONCHECK GAS TYPE INSTALLATIONINSTALLATION ITEMS LOCATING FIREPLACEINSTALLATION BUILT-INFIREPLACE INSTALLATIONContinued INSTALLATION OPTIONAL MANTEL INSTALLATIONMantel Clearances for Built-InInstallation NATURAL GAS VENT-FREEFIREPLACE SYSTEMInstalling Blower Assembly INSTALLING BLOWER ACCESSORY GA3450TRemoving Upper Louver Assembly Removing Valve Cover ShieldNATURAL GAS VENT-FREEFIREPLACE SYSTEM INSTALLATION9. Install the switch plate on the valve ContinuedINSTALLATION For Built-InInstallationContinued Attaching Wood Base to Solid Floor CONNECTING TO GAS SUPPLYExtension Cord INSTALLATIONINSTALLATION Installation Items NeededContinued CHECKING GAS CONNECTIONS Pressure Testing Gas Supply Piping SystemPressure Testing Fireplace Gas Connections INSTALLATIONOPERATING FIREPLACE FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS TO TURN OFF GAS TO APPLIANCE MANUAL LIGHTING PROCEDUREINSPECTING BURNER THERMOSTAT CONTROL OPERATIONCABINET CLEANING AND MAINTENANCEBURNER FLAME PATTERN Air PassagewaysPOSSIBLE CAUSE TROUBLESHOOTINGOBSERVED PROBLEM REMEDYOBSERVED PROBLEM Maintenance, pageTROUBLESHOOTING ContinuedTROUBLESHOOTING ing Gas Connections, page1. Refer to Air for Combustion and Venti OBSERVED PROBLEMSERVICE HINTS SPECIFICATIONSREPLACEMENT PARTS TECHNICAL SERVICEFMH26TN ILLUSTRATED PARTS BREAKDOWNNATURAL GAS VENT-FREEFIREPLACE SYSTEM DESCRIPTION PARTS LISTFMH26TN PARTS AVAILABLE - NOT SHOWNEQUIPMENT SHUTOFF VALVE - GA5010 ACCESSORIESCLEANING KIT - GCK BRASS TRIM KIT - GA6094Page NOT A UPC WARRANTY INFORMATIONLIMITED WARRANTY Model Serial No Date Purchased