Desa CGCF26PRA Mantel Clearances for BUILT-IN Installation, Optional Mantel Installation

Page 10

VENT-FREE PROPANE COMPACT FIREPLACE

INSTALLATION

Continued

MANTEL CLEARANCES FOR BUILT-IN INSTALLATION

If placing mantel above built-in fireplace, you must meet minimum clearance between mantel shelf and top of fireplace opening. If your installation does not meet the mini- mum clearances in Figure 11, you must:

• raise the mantel to an acceptable height,

OR

• remove the mantel.

OPTIONAL MANTEL

INSTALLATION

Note: Refer to instructions provided with the mantel for assembly instructions. Refer to instructions below for system installa- tion. Refer to instructions on page 4 for firebox assembly. Blower accessory should be installed if it is being used (see Accesso- ries, page 24).

1.Unscrew four brass screws that attach top louver to fireplace. Remove louver from fireplace and set aside.

2.Place fireplace on wood base.

3.Place mantel around fireplace/base as- sembly.

4.Assemble brass trim kit. See Assem- bling Brass Trim.

5.Firmly snap brass trim kit on shoulder screws. Shoulder screws are located on fireplace cabinet (see Figure 12).

6.Align brass trim kit for flush fit around opening.

7.Use two 3" wood screws provided and attach fireplace base to wooden base (see Figure 12).

8.Remove brass trim kit and mantel. Be careful not to damage wall or mantel.

9.Place wood base next to wall at instal- lation location.

10.Attach wood base to floor with two 1 3/4" black screws provided (see Figure 13). If the floor is concrete use anchor method (see Attaching Wood Base to Solid Floor, page 11).

11.Install gas line. See Connecting To Gas Supply, page 11.

12.Check for leaks. See Checking Gas Connections, page 13.

13.Place mantel around fireplace. Be care- ful not to damage wall or mantel.

14.Place brass trim kit on the shoulder screws located on the side and top of the fireplace. Firmly snap the brass trim over the shoulder screws on fireplace (see Figure 12).

15.Adjust assembly to remove any gaps. Attach remaining two 3" wood screws from hardware pack through openings inside of fireplace sides into the man- tel. The openings are located at top be- hind the area for the brass louvers (see Figure 13).

16.Reinstall top brass louvers.

Mantel Shelf

Note: All vertical

10"

measurements

are from top of

8"

fireplace

6"

opening to

2

1/2"

bottom of

 

 

mantel shelf.

Minimum Non-

Combustible

Material

13"

16"

19"

21"

Figure 11 - Minimum Mantel Clearances for Built-In Installation

Hole for 3" wood

screw for attaching

Shoulder Screws fireplace to wooden base

Hole for 3" wood

Assembled

screw for attaching

Brass Trim

fireplace to mantel

 

Figure 12 - Attaching Brass Trim to Fireplace

1 3/4" Screw

Wood Base

Figure 13 - Attaching Wood Base to Floor

Assembling Brass Trim (Brass trim shipped with mantel)

1.Remove packaging from three remain- ing pieces of brass trim.

2.Locate two adjusting plates with set screws, and two shims in the hardware packet.

3.Align shim under adjusting plate as shown in Figure 14.

4.Slide one end of adjusting plate/shim in slot on mitered edge of top brass trim (see Figure 14).

5.Slide other end of adjusting plate/shim in slot on mitered edge of side brass trim (see Figure 14).

6.While firmly holding edges of brass trim together, tighten both set screws on the adjusting plate with slotted screwdriver.

7.Repeat steps 1 through 6 for other corner.

8.Set Brass Assembly aside for later in- stallation.

Slot

Set ScrewsTop

Brass

Trim

Shim

Mitered Edge

 

Adjusting

Plate

Side

SlotBrass

Trim

Figure 14 - Assembling Brass Trim

10

105616

Image 10
Contents VENT-FREE PROPANE/LP GAS Compact Fireplace What to do if YOU Smell GASSafety Information VENT-FREE Propane Compact FireplaceProduct Identification Product FeaturesRemote Control Accessories Local CodesAssembling Fireplace AssemblyInstalling Log Assembling HoodUnusually Tight Construction AIR for Combustion and VentilationProviding Adequate Ventilation Confined and Unconfined SpaceDetermining FRESH-AIR Flow for Fireplace Location AIR for Combustion VentilationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Check GAS Type InstallationInstallation Items Locating FireplaceBUILT-IN Fireplace Installation DepthOptional Mantel Installation Mantel Clearances for BUILT-IN InstallationAssembling Brass Trim Brass trim shipped with mantel Connecting to GAS Supply Attaching Wood Base to Solid FloorConnecting Fireplace to GAS Supply Installation Items NeededPressure Testing Fireplace Gas Connections Pressure Testing Gas Supply Piping SystemChecking GAS Connections Installing Receiver Installing 9-Volt Battery in Hand- Held Remote Control UnitOperating Fireplace For Your Safety Read Before LightingLighting Instructions To Turn OFF GAS To Appliance Manual Lighting ProcedureOptional Remote Operation Cleaning and Maintenance Inspecting BurnersTechnical Service Replacement PartsSpecifications Service HintsTroubleshooting Observed Problem Possible Cause RemedyMaintenance, Top Illustrated Parts Breakdown CGCF26PRAParts List KEY Description QTYAccessories Parts Centrals Halco EnterprisesWarranty Information

CGCF26PRA specifications

Desa CGCF26PRA is a modern heater that combines advanced technology with user-friendly features to deliver efficient warmth for home and outdoor spaces. This product is particularly known for its reliability and performance as a convection heater.

One of the standout features of the Desa CGCF26PRA is its powerful 26,000 BTU output, enabling it to effectively heat large areas quickly. This makes it an ideal choice for both residential and commercial applications, especially during the colder months when efficient heating solutions are critical. The heater is designed to operate on liquid propane, which is both cost-effective and readily available, ensuring users can keep their environments comfortably warm without breaking the bank.

In terms of technology, the Desa CGCF26PRA is equipped with an electronic ignition system that provides a reliable start-up with the push of a button. This modern feature eliminates the need for matches or lighters, enhancing convenience and safety. Additionally, the heater is built with safety features such as a safety shut-off valve, which automatically turns off the gas supply in the event of a malfunction, ensuring peace of mind for users concerned about safety.

The design of the Desa CGCF26PRA facilitates easy mobility, thanks to its lightweight construction and integrated handle. It features a compact size that allows it to fit effortlessly in various spaces, whether it's a garage, workshop, or outdoor setting. The heater also has a versatile design that complements a wide range of environments without being an eyesore.

Furthermore, the heater operates quietly, which is an essential characteristic for maintaining a comfortable atmosphere without disruptive noise. Its durable construction ensures longevity, even when subjected to regular use in demanding conditions.

In conclusion, the Desa CGCF26PRA heater stands out for its robust heating capability, modern ignition technology, safety features, portability, and quiet operation. These characteristics make it an excellent investment for anyone in need of an effective heating solution for various settings and applications.