Desa CF26PR installation manual Installing Blower Assembly GA3450T, Installing Snap Bushings

Page 10

CF26PR

VENT-FREE PROPANE/LP BAY FRONT FIREPLACE

INSTALLATION

Continued

4.Place brass trim on the shoulder screws located on the side and top of the fireplace. Firmly snap the brass trim over the shoul- der screws on fireplace (see Figure 13).

5.Place mantel base close to wall in de- sired fireplace location.

6.Install gas line. See Connecting To Gas Supply, page 12

7.Carefully place fireplace on mantel base and center left to right. Check for gas leaks. See Checking Gas Connections, page 14.

8.Refer to instructions provided with the mantel for permanent attachment to wall.

9.Slide mantel around fireplace. Be care- ful not to damage wall or mantel.

10.Adjust assembly to remove any gaps. From back side of fireplace, attach two 2" wood screws through base mount- ing blocks attached to bottom sides of mantel into base (see instructions pro- vided with mantel).

11.Attach remaining two 3" wood screws from hardware pack through openings inside of fireplace sides into the mantel. See Figure 12, page 9, for screw hole location.

INSTALLING BLOWER ASSEMBLY - GA3450T

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improperanddangerousoperation.

CAUTION: Verify proper op- eration after servicing.

Note: If you are using a mantel with your heater, use the following instructions. If your heater is built-in, see For Built-In In- stallation on page 11.

1.Screen and hood should be removed from fireplace (see page 9). Remove log set and set aside.

2.Install snap bushings found in hardware kit into both holes in rear of blower control shield (see Figure 14).

Blower

 

Control

Snap

Shield

Bushing

3.Make sure the wire harness is firmly connected to the terminals on the blower bracket assembly.

4.Note the wire locations on back of AUTO/OFF/ON switch. Carefully re- move red wire from the AUTO termi- nal and blue wire from the ON termi- nal. Black wire can remain on the middle or OFF terminal (see Figure 15).

5.Carefully disconnect green and white wires from power cord harness at their insulated connectors.

6.In top of the heater cabinet, locate the four mounting holes on the outer cas- ing. Align these four holes with those on the blower bracket assembly. Attach blower bracket assembly to the outer casing with 4 - #10 screws provided (see Figure 15).

7.Route the wire harness through the hole to the left side of heat deflector. Pull wire harness through lower opening to the left of the blower control shield. (see Figure 15).

8.Insert the 4 wire harness into one of the round holes in the rear of the blower con- trol shield and through the rectangular hole in the front of shield (see Figure 15).

Shoulder

Figure 14 - Installing Snap Bushings

Screws

 

 

 

Blower Bracket

 

Assembly

 

 

Screw

 

 

Switch

 

Assembled

 

Wire Harness

 

 

Brass Trim

 

Power

 

 

Cord

Figure13-AttachingBrassTrimtoFireplace

Blue

Red

 

 

 

Switch Plate

Wire

 

 

Harness

Blower

Control

Shield

Shield Cover

Wiring

Routing Hole

Heat Deflector

Figure 15 - Installing Blower Bracket Assembly

For more information, visit www.desatech.com

10

105442

Page 9 Page 11
Image 10
Page 9 Page 11
Contents VENT-FREE PROPANE/LP GAS BAY Front Fireplace What to do if YOU Smell GASSafety Information VENT-FREE PROPANE/LP BAY Front FireplaceLocal Codes Product FeaturesRemote Control Accessories UnpackingUnusually Tight Construction AIR for Combustion and VentilationProviding Adequate Ventilation Confined and Unconfined SpaceDetermining FRESH-AIR Flow for Fireplace Location AIR for Combustion VentilationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Check GAS Type InstallationInstallation Items Locating FireplaceBUILT-IN Fireplace Installation DepthRemoving Brick Liner Retainer Mantel Clearances for BUILT-IN InstallationOptional Mantel Installation Assembling Brass TrimInstalling Blower Assembly GA3450T Installing Snap BushingsFor Built-In Installation Blower Control Shield Clamp WireConnecting to GAS Supply With 1/8 NPT TapConnecting Fireplace to GAS Supply Installation Items NeededPressure Testing Gas Supply Piping System Pressure Testing Fireplace Gas ConnectionsChecking GAS Connections Installing Wireless Remote Control Accessory Installing LogsOptional Wireless HAND- Held Remote Control Accessories Cghrc & Cghrct Series Installing ReceiverFor Your Safety Read Before Lighting Instructions Operating FireplaceTo Turn OFF GAS To Appliance Manual Lighting ProcedureOperating Heater Optional Remote OperationBurner Flame Pattern Inspecting BurnersPilot Flame Pattern Burner Primary AIR HolesCleaning and Maintenance Replacement PartsTroubleshooting Observed Problem Possible Cause RemedyMaintenance, Top Technical Service Parts Centrals SpecificationsService Hints Wiring DiagramIllustrated Parts Breakdown CF26PRParts List KEY Part Number Description QTY20-1 11-1 20-2 20-3 11-2 KEY CF26PR Description QTY Accessories Brass Accent Trim GA6095105442 Warranty Information International

CF26PR specifications

Desa CF26PR is a cutting-edge energy-efficient home solution that combines contemporary design with advanced technology to create a sustainable living environment. This model is particularly popular among eco-conscious homeowners looking to minimize their carbon footprint while enjoying modern comforts.

One of the standout features of the Desa CF26PR is its innovative insulation technology, which ensures optimal thermal performance throughout the year. The advanced insulation materials used in the walls and roof effectively prevent heat loss in the winter and heat gain in the summer, contributing to lower energy bills and enhanced comfort. The design also allows for natural ventilation, promoting air circulation and reducing reliance on artificial cooling systems.

The home is equipped with a state-of-the-art solar energy system, harnessing sunlight to generate electricity and significantly reducing dependency on traditional power sources. This solar technology powers essential appliances and lighting within the home, further contributing to its energy-efficient profile. Smart home integration is another key characteristic of the Desa CF26PR, allowing residents to control lighting, heating, and security systems through mobile devices or voice commands.

The interior layout of Desa CF26PR is thoughtfully designed for functionality and aesthetics, featuring open-concept living spaces that maximize natural light. High ceilings and large windows create an inviting atmosphere, making the home feel spacious and airy. The choice of sustainable materials in construction and interior finishes illustrates a commitment to both quality and environmental responsibility.

Additionally, the Desa CF26PR offers a range of customizable options, allowing buyers to tailor the design elements and features to suit their individual needs. This adaptability makes it suitable for families of all sizes, providing ample space with smart storage solutions.

In conclusion, Desa CF26PR stands out as an exemplary model in the realm of sustainable housing. Its integration of energy-efficient technologies, sustainable materials, and modern design features positions it as a leading choice for environmentally-conscious homeowners. Whether it's the advanced insulation, solar energy capabilities, or smart technology integration, the Desa CF26PR embodies the future of smart and sustainable living.
Top Page Image Contents