Desa CF26PR Mantel Clearances for BUILT-IN Installation, Removing Brick Liner Retainer

Page 9

OWNER’S MANUAL

INSTALLATION

Continued

MANTEL CLEARANCES FOR BUILT-IN INSTALLATION

NOTICE: Surface temperatures of adjacent walls and mantels be- come hot during operation. Walls and mantels above the firebox may become hot to the touch. If installed properly, these tempera- tures meet the requirement of the national product standard. Fol- low all minimum clearances shown in this manual.

If placing mantel above built-in fireplace, you must meet minimum clearance between mantel shelf and top of fireplace opening.

NOTICE: If your installation does not meet the minimum clearances shown, you must do one of the following:

raise the mantel to an accept- able height

remove the mantel

Note: All vertical

 

Mantel Shelf

10"

 

 

 

 

measurements

 

 

 

 

are from top of

8"

 

 

 

 

 

 

 

 

fireplace

6"

 

 

 

 

opening to

 

 

 

 

2 1/2"

 

 

 

 

bottom of

 

 

 

 

mantel shelf.

 

 

 

 

 

Minimum Non-

 

 

 

 

 

Combustible

 

 

 

 

 

Material

13"

16"

19"

21"

 

 

 

 

 

 

 

 

 

Figure 8 - Minimum Mantel Clearances for Built-In Installation

REMOVING BRICK LINER RETAINER

1.Using Phillips screw driver, remove 2 screws attaching brick liner retainers to vertical sides.

2.Remove brick liner retainers and discard. Replace 2 screws into vertical sides.

ASSEMBLING BRASS TRIM

(Brass trim shipped with mantel)

1.Remove packaging from three pieces of brass trim.

2.Locate two adjusting plates with set screws, and two shims in the hardware packet.

3.Align shim under adjusting plate as shown in Figure 9.

4.Slide one end of adjusting plate/shim in slot on mitered edge of top brass trim (see Figure 9).

5.Slide other end of adjusting plate/shim in slot on mitered edge of side brass trim (see Figure 9).

6.While firmly holding edges of brass trim together, tighten both set screws on the adjusting plate with slotted screwdriver.

7.Repeat steps 1 through 6 for other corner.

8.Set brass assembly aside for later installation.

 

Slot

Top

Set Screws

Brass

 

 

 

Trim

 

Shim

Mitered

 

Edge

 

 

Adjusting

 

Side

Plate

 

 

Brass

Slot

 

 

Trim

 

 

Figure 9 - Assembling Brass Trim

OPTIONAL MANTEL

INSTALLATION

Note: Refer to instructions provided with the mantel for assembly instructions. Refer to instructions below for system installa- tion. If using blower accessory (see Acces- sories, page 28), see installation instruc- tions on pages 10 and 11.

1.Choose location for fireplace and in- stall gas supply line.

2.Remove screen from fireplace by re- moving screws in each end of screen rod (see Figure 10). Hold screen rod cover while removing five hex head screws underneath hood (see Figure 11). Carefully lift and pull out hood (see Figure 12).

3.Assemble brass trim kit. See Assem- bling Brass Trim, column 2.

Figure 10 - Removing Screen

Hood

Screen

Rod

Cover

Screw

Figure 11 - Removing Hood Screws

Mantel Screw

Location

Figure 12 - Removing Hood

Continued

105442

9

For more information, visit www.desatech.com

Image 9
Contents What to do if YOU Smell GAS VENT-FREE PROPANE/LP GAS BAY Front FireplaceVENT-FREE PROPANE/LP BAY Front Fireplace Safety InformationRemote Control Accessories Product FeaturesLocal Codes UnpackingProviding Adequate Ventilation AIR for Combustion and VentilationUnusually Tight Construction Confined and Unconfined SpaceAIR for Combustion Ventilation Determining FRESH-AIR Flow for Fireplace LocationDetermining if You Have a Confined or Unconfined Space Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Installation Items InstallationCheck GAS Type Locating FireplaceDepth BUILT-IN Fireplace InstallationOptional Mantel Installation Mantel Clearances for BUILT-IN InstallationRemoving Brick Liner Retainer Assembling Brass TrimInstalling Snap Bushings Installing Blower Assembly GA3450TBlower Control Shield Clamp Wire For Built-In InstallationWith 1/8 NPT Tap Connecting to GAS SupplyInstallation Items Needed Connecting Fireplace to GAS SupplyPressure Testing Fireplace Gas Connections Pressure Testing Gas Supply Piping SystemChecking GAS Connections Optional Wireless HAND- Held Remote Control Accessories Installing LogsInstalling Wireless Remote Control Accessory Cghrc & Cghrct Series Installing ReceiverOperating Fireplace For Your Safety Read Before Lighting InstructionsOperating Heater Manual Lighting ProcedureTo Turn OFF GAS To Appliance Optional Remote OperationPilot Flame Pattern Inspecting BurnersBurner Flame Pattern Burner Primary AIR HolesReplacement Parts Cleaning and MaintenanceObserved Problem Possible Cause Remedy TroubleshootingMaintenance, Top Service Hints SpecificationsTechnical Service Parts Centrals Wiring DiagramCF26PR Illustrated Parts BreakdownKEY Part Number Description QTY Parts List20-1 11-1 20-2 20-3 11-2 KEY CF26PR Description QTY Brass Accent Trim GA6095 Accessories105442 International Warranty Information

CF26PR specifications

Desa CF26PR is a cutting-edge energy-efficient home solution that combines contemporary design with advanced technology to create a sustainable living environment. This model is particularly popular among eco-conscious homeowners looking to minimize their carbon footprint while enjoying modern comforts.

One of the standout features of the Desa CF26PR is its innovative insulation technology, which ensures optimal thermal performance throughout the year. The advanced insulation materials used in the walls and roof effectively prevent heat loss in the winter and heat gain in the summer, contributing to lower energy bills and enhanced comfort. The design also allows for natural ventilation, promoting air circulation and reducing reliance on artificial cooling systems.

The home is equipped with a state-of-the-art solar energy system, harnessing sunlight to generate electricity and significantly reducing dependency on traditional power sources. This solar technology powers essential appliances and lighting within the home, further contributing to its energy-efficient profile. Smart home integration is another key characteristic of the Desa CF26PR, allowing residents to control lighting, heating, and security systems through mobile devices or voice commands.

The interior layout of Desa CF26PR is thoughtfully designed for functionality and aesthetics, featuring open-concept living spaces that maximize natural light. High ceilings and large windows create an inviting atmosphere, making the home feel spacious and airy. The choice of sustainable materials in construction and interior finishes illustrates a commitment to both quality and environmental responsibility.

Additionally, the Desa CF26PR offers a range of customizable options, allowing buyers to tailor the design elements and features to suit their individual needs. This adaptability makes it suitable for families of all sizes, providing ample space with smart storage solutions.

In conclusion, Desa CF26PR stands out as an exemplary model in the realm of sustainable housing. Its integration of energy-efficient technologies, sustainable materials, and modern design features positions it as a leading choice for environmentally-conscious homeowners. Whether it's the advanced insulation, solar energy capabilities, or smart technology integration, the Desa CF26PR embodies the future of smart and sustainable living.