Desa CF26PR Installing Logs, Optional Wireless HAND- Held Remote Control Accessories

Page 15

OWNER’S MANUAL

INSTALLATION

Continued

INSTALLING LOGS

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury.

CAUTION: After installation and periodically thereafter, check to ensure that no flame comes in contact with any log. With the heater set to High, check to see if flames contact any log. If so, re- position logs according to the log installation instructions in this manual. Flames contacting logs will create soot.

It is very important to install the logs exactly as instructed. Do not modify logs. Only use logs supplied with heater.

Place one-piece log set on grate to fit as illustrated in Figure 25. Make sure back section of log set is seated into “U”-shaped cutout in center of chassis (see Figure 25). IMPORTANT: Make sure log does not cover any burner ports (see Figure 26).

One Piece Log Set

Burner

Burner

One Piece Log Set

Ports

 

Figure 26 - Installing One-Piece Log set (Top View)

OPTIONAL WIRELESS HAND- HELD REMOTE CONTROL ACCESSORIES

(CGHRC & CGHRCT Series)

Installing Receiver

1.Disconnect switch wires from the con- trol valve.

2.Remove screws and nuts.

3.Remove switch plate (see Figure 27). Discard after removing.

4.Install remote receiver unit onto gas log heater base using clips (2) and insulat- ing washers provided.

5.Push clips firmly into place (see Fig- ure 28).

6.Connect wires as shown in Figure 29.

Front

Screw

Back

Back

Nut

Nut Wires

Figure 27 - Switch Plate and Wiring Harness (Switch Plate and Orientation May Vary Depending On Model)

Front

Mounting

Clips

Back

Remote

Receiver

Insulating Washers

Figure 28 - Installing Remote Receiver

Valve

White Wire

From Receiver

Red Wire From

Receiver

Figure 29 - Connecting Wires

INSTALLING WIRELESS REMOTE CONTROL ACCESSORY

Two 9-volt alkaline batteries (not included) are required to operate this heater with the wireless hand held remote control set. One battery must be installed in the receiver and one in the hand-held remote control unit. Note: Only use alkaline batteries.

Installing 9-Volt Battery in Receiver

1.Locate back of receiver under front burner of heater.

2.Locate the battery clip mounted on the back of the receiver.

3.Slide a 9-volt battery through the clip.

4.Attach the terminal wires to the battery.

Receiver

"U"-shaped

Chassis Cutout in Chassis

Figure 25 - Installing One-Piece Log Set

9-Volt Battery

Terminal

Wires

Battery

Clip

Figure 30 - Installing Receiver on the

Back of the Base

Continued

105442

15

For more information, visit www.desatech.com

Image 15
Contents What to do if YOU Smell GAS VENT-FREE PROPANE/LP GAS BAY Front FireplaceVENT-FREE PROPANE/LP BAY Front Fireplace Safety InformationUnpacking Product FeaturesRemote Control Accessories Local CodesConfined and Unconfined Space AIR for Combustion and VentilationProviding Adequate Ventilation Unusually Tight ConstructionAIR for Combustion Ventilation Determining FRESH-AIR Flow for Fireplace LocationDetermining if You Have a Confined or Unconfined Space Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Locating Fireplace InstallationInstallation Items Check GAS TypeDepth BUILT-IN Fireplace InstallationAssembling Brass Trim Mantel Clearances for BUILT-IN InstallationOptional Mantel Installation Removing Brick Liner RetainerInstalling Snap Bushings Installing Blower Assembly GA3450TBlower Control Shield Clamp Wire For Built-In InstallationWith 1/8 NPT Tap Connecting to GAS SupplyInstallation Items Needed Connecting Fireplace to GAS SupplyPressure Testing Fireplace Gas Connections Pressure Testing Gas Supply Piping SystemChecking GAS Connections Cghrc & Cghrct Series Installing Receiver Installing LogsOptional Wireless HAND- Held Remote Control Accessories Installing Wireless Remote Control AccessoryOperating Fireplace For Your Safety Read Before Lighting InstructionsOptional Remote Operation Manual Lighting ProcedureOperating Heater To Turn OFF GAS To ApplianceBurner Primary AIR Holes Inspecting BurnersPilot Flame Pattern Burner Flame PatternReplacement Parts Cleaning and MaintenanceObserved Problem Possible Cause Remedy TroubleshootingMaintenance, Top Wiring Diagram SpecificationsService Hints Technical Service Parts CentralsCF26PR Illustrated Parts BreakdownKEY Part Number Description QTY Parts List20-1 11-1 20-2 20-3 11-2 KEY CF26PR Description QTY Brass Accent Trim GA6095 Accessories105442 International Warranty Information

CF26PR specifications

Desa CF26PR is a cutting-edge energy-efficient home solution that combines contemporary design with advanced technology to create a sustainable living environment. This model is particularly popular among eco-conscious homeowners looking to minimize their carbon footprint while enjoying modern comforts.

One of the standout features of the Desa CF26PR is its innovative insulation technology, which ensures optimal thermal performance throughout the year. The advanced insulation materials used in the walls and roof effectively prevent heat loss in the winter and heat gain in the summer, contributing to lower energy bills and enhanced comfort. The design also allows for natural ventilation, promoting air circulation and reducing reliance on artificial cooling systems.

The home is equipped with a state-of-the-art solar energy system, harnessing sunlight to generate electricity and significantly reducing dependency on traditional power sources. This solar technology powers essential appliances and lighting within the home, further contributing to its energy-efficient profile. Smart home integration is another key characteristic of the Desa CF26PR, allowing residents to control lighting, heating, and security systems through mobile devices or voice commands.

The interior layout of Desa CF26PR is thoughtfully designed for functionality and aesthetics, featuring open-concept living spaces that maximize natural light. High ceilings and large windows create an inviting atmosphere, making the home feel spacious and airy. The choice of sustainable materials in construction and interior finishes illustrates a commitment to both quality and environmental responsibility.

Additionally, the Desa CF26PR offers a range of customizable options, allowing buyers to tailor the design elements and features to suit their individual needs. This adaptability makes it suitable for families of all sizes, providing ample space with smart storage solutions.

In conclusion, Desa CF26PR stands out as an exemplary model in the realm of sustainable housing. Its integration of energy-efficient technologies, sustainable materials, and modern design features positions it as a leading choice for environmentally-conscious homeowners. Whether it's the advanced insulation, solar energy capabilities, or smart technology integration, the Desa CF26PR embodies the future of smart and sustainable living.