Desa M36, VM42 installation manual Framing, Installing Transition Pipe and Starter Collar

Page 8

8

PRE-INSTALLATION PREPARATION

Framing

Installing Transition Pipe and Starter Collar

PRE-INSTALLATION

PREPARATION

Continued

FRAMING

1.Frame appliance enclosure as illustrated in Figures 7 and 8.

Note: If a wall covering is used to line the enclosure, then all measurements must be from the surface of the covering.

2.Place the appliance into the framing and secure it.

Note: If appliance is to be raised above floor level, a platform must be built to support the appliance.

3.Install the supply line to the appliance using a 1/2" NPT black iron gas line terminating 2 5/16" above the bottom of the appli- ance. The gas line may be installed from either side or from the bottom of the appliance (see Figure 19, page 12).

4.Feed flexible gas line through one of three gas line conduit sleeve and repack insulation to cover any openings. Prepare the incom- ing gas line with teflon tape or pipe joint compound and hook-up incoming gas line to the flexible gas line.

Note: If 1/2" NPT black iron pipe does not mate with fitting at the end of flexible gas line, remove fitting and replace with a 37 degree flare 3/4"-12, 1/2" NPT (female) fitting.

WARNING: When finishing appliance, do not overlap combustible material onto the black front face. Brick, tile, or other noncombustible materials may be applied to the face provided that any gap is between the material used and the face is caulked with a noncombustible caulking.

These Dimensions Allow for a 3/4" Clearance at Sides and Back of Fireplace. However, 0" Clearance is Permitted

D

C

A

3/4" Clearance

Not Required

 

 

 

 

at Nailing

 

 

Flanges

 

 

B

 

M36(B,H)/VM36(B,H)

M42(B,H)/VM42(B,H)

A

24 1/2"(622.3mm)

27 9/16"(700.1mm)

B

73 7/8"(1876.4mm)

83 7/8"(2130.4mm)

C

52 3/16"(1326mm)

59 5/16"(1506.6mm)

D

17 1/4"(438.2mm)

19 1/2"(495.3mm)

 

 

 

Figure 8 - Corner Installation Guidelines

INSTALLING TRANSITION PIPE AND STARTER COLLAR

The transition pipe and starter collar shown in Figure 9 are supplied with the fireplace, unattached and ready for installation. Remove the starter collar and set aside. Slide the transition pipe over the vent collar and attach with a minimum of three screws. Replace the starter collar over the transition pipe and attach using four screws located on the leg stands (five used on the model M42). To install B-vent piping, slide the first piece of B-vent over the transition pipe and attach with a minimum of two screws.

 

 

A

 

B

 

 

C

 

 

M36(B,H)/VM36(B,H)

M42(B,H)/VM42(B,H)

A

40 3/8" (1020mm)

44 3/8" (1121mm)

B

21 3/8" (543mm)

23 1/8" (587mm)

C

41 1/4" (1048mm)

48 1/4" (1226mm)

Figure 7 - Rough Opening for Installing in Wall

B-Vent Piping

Starter Collar

Transition Pipe

Vent Collar

Figure 9 - Installing Transition Pipe and Starter Collar

For morevisit www..com

108795-01E

Page 7 Page 9
Image 8
Page 7 Page 9
Contents For Your Safety Vent Decorative GAS FireplaceNatural GAS What to do if YOU Smell GASTable of Contents Safety InformationUnpacking M36B,H/VM36B,H M42B,H/VM42B,H IntroductionBefore YOU Begin Product Specifications ModelClearances PRE-INSTALLATION PreparationSelecting Location Mantel Clearances and Wall Details M36B,H M42B,HVM36B,H VM42B,H M36B,H M42B,H VM36B,H VM42B,HInstalling Transition Pipe and Starter Collar FramingVenting Installation Typical B-Vent ConfigurationChecking for Proper Venting Min Roof PitchInstallation Wall Switch InstallationOptional Wireless HAND-HELD Remote Control Installation Installing ReceiverInstalling 9-Volt Battery in Hand-Held Remote Control Unit GAS Line HOOK-UPEmber and PAN Material Placement OvertightenLOG Placement for M36/VM36 Models Installing Logs 3LOG Placement for M42/VM42 Models Rest the lower part of log 5 on the log 4 and onAppliance Enclosure Installing Optional Glass Door AccessoryCombustion AIR KIT Model AK4 Optional Opening Vent Damper Removing Glass DoorsFor Your Safety Read Before Lighting Operating FireplaceLighting Instructions To Turn OFF GAS to AppliancePilot Assembly Inspecting BurnersOptional HAND-HELD Remote Operation Burner Flame PatternService Hints Replacement Parts Cleaning Maintenance Technical ServiceWiring Diagram Troubleshooting Observed Problem Possible Cause RemedyTroubleshooting Top Gas leak. See Warning statement atIllustrated Parts Breakdown VM42B,H ModelsParts List Description QTYLogset for M42B, H/VM42B, H Models Logs for M36B,H, M42B,H, VM36B,H and VM42B,H ModelsLogset for M36B, H/VM36B, H Models Accessories Warranty Information

M36, VM42 specifications

Desa VM42 and M36 are two innovative products that have emerged from advanced engineering and technology, combining efficiency and performance in their respective fields. These machines are known for their unique features and characteristics that set them apart in the marketplace.

Desa VM42 is engineered for versatility and efficiency, making it an optimal choice for various applications. Its standout feature is its user-friendly interface, which allows operators to quickly adapt to using the machine, reducing the learning curve significantly. The VM42 is equipped with state-of-the-art automation technology, which facilitates precision engineering and minimal human error. This machine also boasts advanced thermal management systems that ensure consistent operation even under high loads, extending its lifespan and maintenance intervals.

On the other hand, the M36 model primarily emphasizes robust durability and power. The M36 comes with a heavy-duty chassis and is built to withstand harsh operating conditions, making it ideal for heavy industrial tasks. Its design includes high-strength materials and reinforced structural components, ensuring resilience against wear and tear. The M36 is equipped with a powerful engine that boosts productivity while maintaining fuel efficiency, a crucial aspect for reducing operational costs.

Both models leverage cutting-edge technologies such as IoT connectivity. This feature allows real-time monitoring and analysis of machine performance, making it easier for operators to handle maintenance proactively. Furthermore, the integration of smart sensors enhances safety by alerting users about potential issues before they escalate.

In terms of customization, Desa provides various options for both the VM42 and M36, allowing users to tailor specifications based on their specific needs. This flexibility ensures that customers can maximize the utility of these machines according to their operational requirements.

Another notable characteristic of both models is their environmental consciousness. Designed with eco-friendly technologies, they help in minimizing emissions and energy consumption. This aligns well with contemporary demands for sustainable practices in industrial operations.

In summary, Desa VM42 and M36 represent the pinnacle of modern engineering, combining user-friendly interfaces, robust designs, and innovative technologies to deliver exceptional performance in various applications. These machines not only enhance productivity but also support sustainable operational practices, making them leaders in their fields.
Top Page Image Contents