Desa HDCFTN Mantel Clearances for BUILT- in Installation, Optional Mantel Installation

Page 12

INSTALLATION

Continued

MANTEL CLEARANCES FOR BUILT- IN INSTALLATION

If placing mantel above built-in fireplace, you must meet minimum clearance between mantel shelf and top of fireplace opening.

NOTICE: Surface temperatures of adjacent walls and mantels become hot during operation. Walls and mantels above the firebox may become hot to the touch. If installed properly, these temperatures meet the requirement of the national product standard. Follow all minimum clearances shown in this manual.

NOTICE: If your installation does not meet the minimum clear- ances shown, you must do one of the following:

•raise the mantel to an accept- able height

•remove the mantel

OPTIONAL MANTEL INSTALLATION

Note: Refer to instructions provided with the man- tel for assembly instructions. Refer to instructions below for system installation. Refer to instructions on page 4 for firebox assembly. Blower accessory should be installed if it is being used (see Installing Blower Accessory GA3450T, page 13).

1.

Unscrew four brass screws that attach top lou-

 

ver to fireplace. Remove louver from fireplace

 

and set aside.

2.

Place fireplace on wood base.

3.

Place mantel around fireplace/base assembly.

4.

Assemble brass trim kit. See Assembling Brass

 

Trim, page 13.

5.

Firmly snap brass trim kit on shoulder screws.

 

Shoulder screws are located on fireplace cabi-

 

net (see Figure 13).

6.

Align brass trim kit for flush fit around opening.

7.

Use two 3" wood screws provided and attach

 

fireplace base to wooden base (see Figure 13).

8.

Remove brass trim kit and mantel. Be careful

 

not to damage wall or mantel.

9.

Place wood base next to wall at installation

 

location.

10.

Attach wood base to floor with two 1 3/4"

 

black screws provided (see Figure 14, page

 

13). If the floor is concrete use anchor method

 

(see Attaching Wood Base to Solid Floor, page

 

14, page 13).

11.

Install gas line. See Connecting To Gas Sup-

Note: All vertical measurements are from top of fireplace opening to bottom of mantel shelf. All measurements are in inches.

Mantel Shelf

10"

8"

6"

2 1/2"

ply, page 16.

12. Check for leaks. See Checking Gas Connec-

tions, page 18.

Hole for 3" Wood Screw for Attaching Fireplace to Mantel

Shoulder Screws

Side of

 

 

 

 

Firebox

13"

16"

19"

21"

 

Figure 12 - Minimum Mantel Clearances

for Built-In Installation

 

Hole for 3"

 

Wood Screw

 

for Attaching

Assembled

Fireplace to

Wooden Base

Brass Trim

 

Figure 13 - Attaching Brass Trim to

 

Fireplace

12

www.desatech.com

111044-01F

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Shown with Optional Cabinet Mantel/Hearth Base Accessory HDCFTP, HDCFTN, Cgcftp and Cgcftn14,000 to 26,000 Btu/Hr with Thermostat Table of Contents Safety Information Local Codes Product InformationProvide adequate clearances around air openings Product Features AssemblyUnpacking Providing Adequate Ventilation Assembling HoodAIR for Combustion Ventilation Determining FRESH-AIR Flow for Heater LocationConfined and Unconfined Space Determining if You Have a Confined or Unconfined SpaceInstallation Ventilation AIRVentilation Air From Inside Building Ventilation Air From OutdoorsInstallation Items Check GAS TypeLocating Fireplace BUILT-IN Fireplace Installation Rough Opening for Installing WallIf you have not assembled firebox, follow instructions on Attaching Fireplace to Wall StudsMantel Clearances for BUILT- in Installation Optional Mantel InstallationInstalling Blower Accessory Removing Upper Louver AssemblyInstalling Blower Assembly Models Cgcftp and Cgcftn Removing Valve Cover ShieldFor Built-In Installation Close lower louver doorConnecting to GAS Supply Attaching Wood Base to Solid FloorExtension Cord Connecting Equipment Shutoff Valve to Heater Control Installation Items NeededChecking GAS Connections Test Pressures In Excess Of 1/2 Psig 3.5 kPaTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa For Your Safety Read Before LightingEquipment Shutoff Valve Propane/LPOperating Fireplace Lighting InstructionsTo Turn OFF GAS To Appliance Shutting Off FireplaceManual Lighting Procedure Inspecting BurnerThermostat Control Operation Burner Flame PatternCleaning Maintenance Burner Injector Holder and Pilot AIR Inlet HoleCabinet Air PassagewaysTroubleshooting Observed Problem Possible Cause RemedyOut when control knob is re Delayed ignition of burner Manifold pressure is too lowODS/pilot lights but flame goes Press in control knob fullyBurner orifice Clean burner see Cleaning Gas regulator defective Nance, Replace gas regulatorAir in gas line Minute Operate burner until air is Air passageways on fireplaceGas leak. See Warning Specifications Replacement PartsService Hints Technical ServiceIllustrated Parts Breakdown Models CGCFTP, CGCFTN, Hdcftp and HdcftnParts List Part Number KEY Hdcftp Hdcftn Cgcftp Cgcftn Description QTYAccessories Parts Centrals FBDWarranty Information Keep this WarrantyLimited Warranty VENT-FREE Compact Fireplace

CGCFTP, CGCFTN 14, HDCFTN specifications

Desa HDCFTN, CGCFTP, and CGCFTN 14 represent a significant advancement in the landscape of modern digital architecture. These entities are characterized by their unique blend of features, technologies, and characteristics that cater to various applications and industries.

At the core of these systems is the high-density computing and flexible trading network (HDCFTN) structure, which allows for scalable operations and enhanced processing capabilities. This architecture is designed to efficiently handle large volumes of data transactions, making it ideal for sectors such as finance, telecommunications, and research institutions. By incorporating distributed computing, HDCFTN can optimize resource allocation and significantly reduce latency compared to traditional centralized systems.

CGCFTP, or the Cloud-based Grid Computing for Financial Transactions Platform, serves as a robust framework that integrates real-time data processing and analysis. Its cloud-native design ensures seamless connectivity and scalability, enabling organizations to operate in a flexible environment. The platform utilizes microservices architecture, which allows for independent deployment and scaling of different components, leading to improved performance and resilience.

Meanwhile, CGCFTN 14 focuses on providing end-to-end solutions for trading and financial operations. It incorporates advanced security protocols and compliance features, addressing the increasing regulatory demands prevalent in the financial sector. Utilizing blockchain technology, CGCFTN 14 ensures data integrity and transparency, creating trust among users while minimizing the risk of fraud or misconduct.

The combination of artificial intelligence (AI) and machine learning (ML) within these frameworks enhances predictive analytics and decision-making processes. With algorithms that learn from historical data, organizations can anticipate market trends and adjust their strategies accordingly. The integration of big data analytics further fuels real-time insights, empowering businesses to respond swiftly to market changes.

Moreover, these innovative systems embrace interoperability, connecting with various existing technologies and platforms. This flexibility allows organizations to leverage their current investments while still benefiting from new technological advancements. In summary, Desa HDCFTN, CGCFTP, and CGCFTN 14 exemplify the future of digital infrastructure, characterized by high density, cloud integration, advanced security, and intelligent analytics, driving efficiency and innovation across industries.
Top Page Image Contents