Desa CGCFTP, CGCFTN 14, HDCFTN Installing Blower Accessory, Removing Upper Louver Assembly

Page 13

INSTALLATION

Continued

13.Place mantel around fireplace. Be careful not to damage wall or mantel.

14.Place brass trim kit on the shoulder screws located on the side and top of the fireplace. Firmly snap the brass trim over the shoulder screws on fireplace (see Figure 13, page 12).

15.Adjust assembly to remove any gaps. Attach remaining two 3" wood screws from hardware pack through openings inside of fireplace sides into the mantel. The openings are located at top behind the area for the louvers (see Figure 13, page 12).

16.Reinstall top louvers.

1 3/4" Screw

Wood Base

Figure 14 - Attaching Wood Base to

Floor

ASSEMBLING BRASS TRIM (Brass trim shipped with mantel)

1.Remove packaging from three remaining pieces of brass trim.

2.Locate two adjusting plates with set screws and two shims in the hardware packet.

3.Align shim under adjusting plate as shown in Figure 15.

4.Slide one end of adjusting plate/shim in slot on mitered edge of top brass trim (see Figure 15).

5.Slide other end of adjusting plate/shim in slot on mitered edge of side brass trim (see Figure 15).

6.While firmly holding edges of brass trim to- gether, tighten both set screws on the adjusting plate with slotted screwdriver.

7.Repeat steps 1 through 6 for other corner.

8.Set brass assembly aside for later installation.

 

 

Top Brass

 

 

Trim

 

 

Set Screws

Slot

 

Adjusting

 

 

Plate

 

 

 

 

 

Side

 

 

Mitered

Brass

 

 

Edge

Trim

 

Shim

 

 

 

Slot

 

 

 

Figure 15 - Assembling Brass Trim

INSTALLING BLOWER ACCESSORY

GA3450T

 

 

Removing Upper Louver Assembly

To install the blower accessory, you must first

remove the upper louver assembly.

 

1.

Lift screen off heater.

 

2.

Remove 4 screws from louver assembly (see

 

Figure 16). Save these screws.

 

3.

Pull louver assembly straight out from the

 

cabinet. Be careful not to scratch the paint.

 

Set louver assembly and screws aside.

 

 

Blower Bracket

 

 

Mounting Holes

 

 

Upper

 

Screws

Louver

 

Assembly

 

 

Figure 16

- Removing Upper Louver

Assembly

 

 

111044-01F

www.desatech.com

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents HDCFTP, HDCFTN, Cgcftp and Cgcftn Shown with Optional Cabinet Mantel/Hearth Base Accessory14,000 to 26,000 Btu/Hr with Thermostat Table of Contents Safety Information Product Information Local CodesProvide adequate clearances around air openings Assembly Product FeaturesUnpacking Assembling Hood Providing Adequate VentilationDetermining FRESH-AIR Flow for Heater Location AIR for Combustion VentilationConfined and Unconfined Space Determining if You Have a Confined or Unconfined SpaceVentilation AIR InstallationVentilation Air From Inside Building Ventilation Air From OutdoorsCheck GAS Type Installation ItemsLocating Fireplace Rough Opening for Installing Wall BUILT-IN Fireplace InstallationAttaching Fireplace to Wall Studs If you have not assembled firebox, follow instructions onOptional Mantel Installation Mantel Clearances for BUILT- in InstallationRemoving Upper Louver Assembly Installing Blower AccessoryRemoving Valve Cover Shield Installing Blower Assembly Models Cgcftp and CgcftnClose lower louver door For Built-In InstallationAttaching Wood Base to Solid Floor Connecting to GAS SupplyExtension Cord Installation Items Needed Connecting Equipment Shutoff Valve to Heater ControlTest Pressures In Excess Of 1/2 Psig 3.5 kPa Checking GAS ConnectionsTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Read Before Lighting For Your SafetyEquipment Shutoff Valve Propane/LPLighting Instructions Operating FireplaceTo Turn OFF GAS To Appliance Shutting Off FireplaceInspecting Burner Manual Lighting ProcedureThermostat Control Operation Burner Flame PatternBurner Injector Holder and Pilot AIR Inlet Hole Cleaning MaintenanceCabinet Air PassagewaysObserved Problem Possible Cause Remedy TroubleshootingDelayed ignition of burner Manifold pressure is too low Out when control knob is reODS/pilot lights but flame goes Press in control knob fullyGas regulator defective Nance, Replace gas regulator Burner orifice Clean burner see CleaningAir in gas line Minute Operate burner until air is Air passageways on fireplaceGas leak. See Warning Replacement Parts SpecificationsService Hints Technical ServiceModels CGCFTP, CGCFTN, Hdcftp and Hdcftn Illustrated Parts BreakdownPart Number KEY Hdcftp Hdcftn Cgcftp Cgcftn Description QTY Parts ListAccessories FBD Parts CentralsKeep this Warranty Warranty InformationLimited Warranty VENT-FREE Compact Fireplace

CGCFTP, CGCFTN 14, HDCFTN specifications

Desa HDCFTN, CGCFTP, and CGCFTN 14 represent a significant advancement in the landscape of modern digital architecture. These entities are characterized by their unique blend of features, technologies, and characteristics that cater to various applications and industries.

At the core of these systems is the high-density computing and flexible trading network (HDCFTN) structure, which allows for scalable operations and enhanced processing capabilities. This architecture is designed to efficiently handle large volumes of data transactions, making it ideal for sectors such as finance, telecommunications, and research institutions. By incorporating distributed computing, HDCFTN can optimize resource allocation and significantly reduce latency compared to traditional centralized systems.

CGCFTP, or the Cloud-based Grid Computing for Financial Transactions Platform, serves as a robust framework that integrates real-time data processing and analysis. Its cloud-native design ensures seamless connectivity and scalability, enabling organizations to operate in a flexible environment. The platform utilizes microservices architecture, which allows for independent deployment and scaling of different components, leading to improved performance and resilience.

Meanwhile, CGCFTN 14 focuses on providing end-to-end solutions for trading and financial operations. It incorporates advanced security protocols and compliance features, addressing the increasing regulatory demands prevalent in the financial sector. Utilizing blockchain technology, CGCFTN 14 ensures data integrity and transparency, creating trust among users while minimizing the risk of fraud or misconduct.

The combination of artificial intelligence (AI) and machine learning (ML) within these frameworks enhances predictive analytics and decision-making processes. With algorithms that learn from historical data, organizations can anticipate market trends and adjust their strategies accordingly. The integration of big data analytics further fuels real-time insights, empowering businesses to respond swiftly to market changes.

Moreover, these innovative systems embrace interoperability, connecting with various existing technologies and platforms. This flexibility allows organizations to leverage their current investments while still benefiting from new technological advancements. In summary, Desa HDCFTN, CGCFTP, and CGCFTN 14 exemplify the future of digital infrastructure, characterized by high density, cloud integration, advanced security, and intelligent analytics, driving efficiency and innovation across industries.
Top Page Image Contents