Desa HDCFTN Cleaning Maintenance, Burner Injector Holder and Pilot AIR Inlet Hole, Cabinet

Page 22

CLEANING AND

MAINTENANCE

WARNING: Turn off fireplace and let cool before cleaning.

CAUTION: You must keep control areas, burner and cir- culating air passageways of fireplace clean. Inspect these areas of fireplace before each use. Have fireplace inspected yearly by a qualified service person. Fireplace may need more frequent cleaning due to excessive lint from carpeting, bedding material, pet hair, etc.

WARNING: Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting and property damage.

BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLE

The primary air inlet holes allow the proper amount of air to mix with the gas. This provides a clean burning flame. Keep these holes clear of dust, dirt, lint and pet hair. Clean these air inlet holes prior to each heating season. Blocked air holes will create soot. We recommend that you clean the unit every three months during operation and have heater inspected yearly by a qualified service person.

We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than 30 PSI. Your local computer store, hardware store or home center may carry compressed air in a can. You can use a vacuum cleaner in the blow position. If using com- pressed air in a can, please follow the directions on the can. If you don't follow directions on the can, you could damage the pilot assembly.

1.Shut off the unit, including the pilot. Allow the unit to cool for at least thirty minutes.

2.Inspect burner, pilot and primary air inlet holes on injector holder for dust and dirt (see Figure 36).

3.Blow air through the ports/slots and holes in the burner.

4.Check the injector holder located at the end of the burner tube again. Remove any large particles of dust, dirt, lint or pet hair with a soft cloth or vacuum cleaner nozzle.

5.Blow air into the primary air holes on the injector holder.

6.In case any large clumps of dust have now been pushed into the burner repeat steps 3 and 4.

Clean the pilot assembly also. A yellow tip on the pilot flame indicates dust and dirt in the pilot as- sembly. There is a small pilot air inlet hole about two inches from where the pilot flame comes out of the pilot assembly (see Figure 37). With the unit off, lightly blow air through the air inlet hole. You may blow through a drinking straw if compressed air is not available.

Ports/Slots

Injector

Holder

Burner Tube

Primary Air

Inlet Holes

Figure 36 - Injector Holder On Outlet

Burner Tube

Pilot Assembly

Pilot Air Inlet Hole

Figure 37 - Pilot Inlet Air Hole

(Propane/LP Shown)

CABINET

Air Passageways

•Use a vacuum cleaner or pressurized air to clean.

Exterior

•Use a soft cloth dampened with a mild soap and water mixture. Wipe the cabinet to remove dust.

22

www.desatech.com

111044-01F

Page 21 Page 23
Image 22
Page 21 Page 23
Contents HDCFTP, HDCFTN, Cgcftp and Cgcftn Shown with Optional Cabinet Mantel/Hearth Base Accessory14,000 to 26,000 Btu/Hr with Thermostat Table of Contents Safety Information Product Information Local CodesProvide adequate clearances around air openings Assembly Product FeaturesUnpacking Providing Adequate Ventilation Assembling HoodConfined and Unconfined Space AIR for Combustion VentilationDetermining FRESH-AIR Flow for Heater Location Determining if You Have a Confined or Unconfined SpaceVentilation Air From Inside Building InstallationVentilation AIR Ventilation Air From OutdoorsCheck GAS Type Installation ItemsLocating Fireplace BUILT-IN Fireplace Installation Rough Opening for Installing WallIf you have not assembled firebox, follow instructions on Attaching Fireplace to Wall StudsMantel Clearances for BUILT- in Installation Optional Mantel InstallationInstalling Blower Accessory Removing Upper Louver AssemblyInstalling Blower Assembly Models Cgcftp and Cgcftn Removing Valve Cover ShieldFor Built-In Installation Close lower louver doorAttaching Wood Base to Solid Floor Connecting to GAS SupplyExtension Cord Connecting Equipment Shutoff Valve to Heater Control Installation Items NeededTest Pressures In Excess Of 1/2 Psig 3.5 kPa Checking GAS ConnectionsTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Equipment Shutoff Valve For Your SafetyRead Before Lighting Propane/LPTo Turn OFF GAS To Appliance Operating FireplaceLighting Instructions Shutting Off FireplaceThermostat Control Operation Manual Lighting ProcedureInspecting Burner Burner Flame PatternCabinet Cleaning MaintenanceBurner Injector Holder and Pilot AIR Inlet Hole Air PassagewaysTroubleshooting Observed Problem Possible Cause RemedyODS/pilot lights but flame goes Out when control knob is reDelayed ignition of burner Manifold pressure is too low Press in control knob fullyAir in gas line Minute Operate burner until air is Burner orifice Clean burner see CleaningGas regulator defective Nance, Replace gas regulator Air passageways on fireplaceGas leak. See Warning Service Hints SpecificationsReplacement Parts Technical ServiceIllustrated Parts Breakdown Models CGCFTP, CGCFTN, Hdcftp and HdcftnParts List Part Number KEY Hdcftp Hdcftn Cgcftp Cgcftn Description QTYAccessories Parts Centrals FBDKeep this Warranty Warranty InformationLimited Warranty VENT-FREE Compact Fireplace

CGCFTP, CGCFTN 14, HDCFTN specifications

Desa HDCFTN, CGCFTP, and CGCFTN 14 represent a significant advancement in the landscape of modern digital architecture. These entities are characterized by their unique blend of features, technologies, and characteristics that cater to various applications and industries.

At the core of these systems is the high-density computing and flexible trading network (HDCFTN) structure, which allows for scalable operations and enhanced processing capabilities. This architecture is designed to efficiently handle large volumes of data transactions, making it ideal for sectors such as finance, telecommunications, and research institutions. By incorporating distributed computing, HDCFTN can optimize resource allocation and significantly reduce latency compared to traditional centralized systems.

CGCFTP, or the Cloud-based Grid Computing for Financial Transactions Platform, serves as a robust framework that integrates real-time data processing and analysis. Its cloud-native design ensures seamless connectivity and scalability, enabling organizations to operate in a flexible environment. The platform utilizes microservices architecture, which allows for independent deployment and scaling of different components, leading to improved performance and resilience.

Meanwhile, CGCFTN 14 focuses on providing end-to-end solutions for trading and financial operations. It incorporates advanced security protocols and compliance features, addressing the increasing regulatory demands prevalent in the financial sector. Utilizing blockchain technology, CGCFTN 14 ensures data integrity and transparency, creating trust among users while minimizing the risk of fraud or misconduct.

The combination of artificial intelligence (AI) and machine learning (ML) within these frameworks enhances predictive analytics and decision-making processes. With algorithms that learn from historical data, organizations can anticipate market trends and adjust their strategies accordingly. The integration of big data analytics further fuels real-time insights, empowering businesses to respond swiftly to market changes.

Moreover, these innovative systems embrace interoperability, connecting with various existing technologies and platforms. This flexibility allows organizations to leverage their current investments while still benefiting from new technological advancements. In summary, Desa HDCFTN, CGCFTP, and CGCFTN 14 exemplify the future of digital infrastructure, characterized by high density, cloud integration, advanced security, and intelligent analytics, driving efficiency and innovation across industries.
Top Page Image Contents