Desa H) AND VM42(B, H) AND VM42P(B, M36P Operating Fireplace, For Your Safety Read Before Lighting

Page 16

16

OPERATING FIREPLACE

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

A. This appliance has a pilot which must be lighted by hand.

When lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all around the appliance area

for gas. Be sure to smell next to the floor because some gas

is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

•

Do not try to light any appliance.

•

Do not touch any electric switch; do not use any phone

9.Push in the knob all the way and hold in. Immediately light the pilot manually. Continue to hold the control knob in for about (1) minute after the pilot is lit. Release knob and it will pop back up. Pilot should remain lit. If it goes out, repeat steps 5 through 9.

•If knob does not pop up when released, stop and imme- diately call your service technician or gas supplier.

•If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call your service technician or gas supplier.

10.Turn gas control knob counterclockwise to “ON”. Knob can be turned to “ON” only if the control knob is popped out.

11.Replace front refractory brick access panel.

12.Fully close glass doors if installed.

13.Turn on all electric power to the appliance.

•

in your building.

Immediately call your gas supplier from a neighborʼs

•

phone. Follow the gas supplierʼs instructions.

If you cannot reach your gas supplier, call the fire de-

 

partment.

C. Use only your hand to push in or turn the gas control knob.

Never use tools. If the knob will not push in or turn by hand,

donʼt try to repair it, call a qualified service technician or

gas supplier. Force or attempted repair may result in a fire

or explosion.

IN

Gas Control Knob

ON

T

O

L

I

P

OFF

IN OUT

Pilot

Adjustment

Screw

D. Do not use this appliance if any part has been under water.

Immediately call a qualified service technician to inspect

the appliance and to replace any part of the control system

and any gas control which has been under water.

LIGHTING

INSTRUCTIONS

NOTICE: During initial operation of new heater, burning logs will give off a paper-burning smell. Orange flame will also be present. Open damper or window to vent smell. This will only last a few hours.

1.STOP! Read the safety information, above.

2.Turn wall switch to the OFF position.

3.Turn off all electric power to the appliance.

4.Fully open glass doors if installed.

5.Remove front refractory brick access panel.

6.Turn gas control knob clockwise to the OFF position (see Figure 39).

7.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information above. If you donʼt smell gas, go to the next step.

8.Turn control knob counterclockwise to the PILOT position.

Position Indicator

Figure 39 - Control Knob in the PILOT position

TO TURN OFF GAS

TO APPLIANCE

1.Turn off the wall switch.

2.Turn off all electric power to the appliance if service is to be performed.

3.Fully open glass doors if installed.

4.Remove front hearth brick and control access panel.

5.Turn gas control knob clockwise to “OFF”. Do not force.

6.Replace front refractory brick access panel.

7.Fully close glass doors if installed.

Pilot Burner

Thermopile

Ignitor

Figure 40 - Pilot

For more information, visit www.desatech.com

108795-01M

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Vent Decorative GAS Fireplace OWNER’S Operation and Installation ManualWhat to do if YOU Smell GAS Table of Contents Safety InformationSafety Information UnpackingIntroduction Before YOU BeginProduct Specifications GAS Rating NaturalSelecting Location PRE-INSTALLATION PreparationClearances Mantel Clearances and Wall Details 229mm Materials Header 152mm BSpacer 76mm 38mm MaxInstalling Transition Pipe and Starter Collar PRE-INSTALLATION PreparationFraming Venting Installation Typical B-Vent ConfigurationVenting Installation Checking for Proper VentingWall Switch Installation InstallationOptional Wireless HAND-HELD Remote Control Installation Installation GAS Line HOOK-UPEmber and PAN Material Placement LOG Placement for M36, M36P, VM36 and VM36P ModelsLOG Placement for M42, M42P, VM42 and VM42P Models Lava rock provided around the front and sides of the burnerCombustion AIR KIT Model AK4 Optional Appliance EnclosureInstalling Optional Glass Door Accessory Opening Vent DamperFor Your Safety Read Before Lighting Operating FireplaceLighting Instructions To Turn OFF GAS To AppliancePilot Assembly Inspecting BurnersOperating Fireplace Optional HAND-HELD Remote OperationCleaning Maintenance Service Hints Technical ServiceReplacement Parts Wiring DiagramTroubleshooting Observed Problem Possible Cause RemedyTroubleshooting MainGas leak. See Warning statement at Illustrated Parts Breakdown ModelsParts List Parts Available not ShownIllustrated Parts Breakdown Logsets for ModelsOwners Registration Form Postage Required Accessories Warranty Information

VM36P, H) AND VM42(B, M42P, H) AND VM42P(B, M36P specifications

Desa H), M36P, H) and VM42P(B, M42P, H) and VM42(B are notable entities in the realm of technological solutions, particularly in the fields of engineering and manufacturing. These designations often pertain to advanced machine models or systems that incorporate various characteristics tailored for specific industrial applications.

The Desa H) series is recognized for its robust performance in industrial settings. It typically features enhanced efficiency and durability, making it suitable for rigorous operational environments. The key technologies integrated into the Desa H) models include high-performance motors and precision control systems that ensure optimal functionality. In particular, these systems are designed to minimize energy consumption while maximizing output across diverse applications.

Meanwhile, the M36P and its variants, including the M36P,H), are engineered with versatility in mind. They are equipped with modular components that allow for easy customization based on user requirements. This adaptability is a significant advantage, as it enables operators to modify the system to suit various tasks without extensive reconfiguration. Noteworthy features of the M36P series include advanced user interfaces that facilitate ease of operation and monitoring.

The VM42P(B, M42P, H) series takes innovation a step further by integrating state-of-the-art automation technologies. With features like smart sensors and AI-driven analytics, the VM42 models provide unprecedented levels of precision and reliability. These technologies enable predictive maintenance, allowing users to anticipate potential issues before they arise, thus reducing downtime and operational costs. The VM42(B) variant is particularly appreciated for its high throughput capabilities, making it ideal for mass production settings.

All models share common characteristics such as rugged construction, user-friendly interfaces, and compliance with international safety standards. Additionally, they are designed for scalability, which ensures that businesses can expand their operations with ease as demand grows. Enhanced connectivity options and IoT integration further allow for real-time data analysis and remote monitoring, fostering smarter production environments.

In summary, the Desa H), M36P, H) and VM42P(B, M42P, H) and VM42(B series represent a fusion of innovative engineering and practical application. Each model’s distinct features cater to a broad range of industrial needs, making them indispensable tools in modern manufacturing and engineering landscapes. Through their commitment to efficiency, adaptability, and intelligent technology, these systems pave the way for enhanced productivity and sustainability in various sectors.
Top Page Image Contents