Desa H) AND VM42P(B, H) AND VM42(B, VM36P PRE-INSTALLATION Preparation, Framing

Page 7

PRE-INSTALLATION

PREPARATION

Continued

FRAMING

1.Frame appliance enclosure as illustrated in Figures 7 and 8.

Note: If a wall covering is used to line the enclosure, then all measurements must be from the surface of the covering.

2.Place the appliance into the framing and secure it.

Note: If appliance is to be raised above floor level, a platform must be built to support the appliance.

3.Install the supply line to the appliance using a 1/2" NPT black iron gas line terminating 2 5/16" above the bottom of the ap- pliance. The gas line must be installed through the lower left side access point or alternate access hole in the bottom of the appliance (see Figure 19, page 11).

4.Repack insulation around the gas line to cover any remaining openings in the conduit sleeve. Prepare the incoming gas line with teflon tape or pipe joint compound and hook-up incoming gas line to the flexible gas line.

Note: If 1/2" NPT black iron pipe does not mate with fitting at the end of flexible gas line, remove fitting and replace with a 37 degree flare 3/4"-12, 1/2" NPT (female) fitting.

WARNING: When finishing appliance, do not overlap combustible material onto the black front face. Brick, tile or other noncombustible materials may be applied to the face provided that any gap is between the mate- rial used and the face is caulked with a noncombustible caulking.

7

These Dimensions Allow for a 3/4" Clearance at Sides and Back of Fireplace. However, 0" Clearance is Permitted

D

C

A 3/4" Clearance

Not Required

at Nailing

Flanges

B

 

M36(B,H), M36P(B,H)

M42(B,H), M42P(B,H)

 

VM36(B,H), VM36P(B,H)

VM42(B,H), VM42P(B,H)

A

24 1/2" (622.3 mm)

27 9/16" (700.1 mm)

B

73 7/8" (1876.4 mm)

83 7/8" (2130.4 mm)

C

52 3/16" (1326 mm)

59 5/16" (1506.6 mm)

D

17 1/4" (438.2 mm)

19 1/2" (495.3 mm)

Figure 8 - Corner Installation Guidelines

INSTALLING TRANSITION PIPE AND STARTER COLLAR

The transition pipe and starter collar shown in Figure 9 are supplied with the fireplace, unattached and ready for installation. Remove the starter collar and set aside. Slide the transition pipe over the vent collar and attach with a minimum of three screws. Replace the starter collar over the transition pipe and attach using four screws located on the leg stands (five used on the model M42). To install B-vent piping, slide the first piece of B-vent over the transition pipe and attach with either a minimum of two screws or other means approved by the vent manufacturer.

B-Vent Piping

 

 

A

Starter Collar

 

 

 

 

B

 

 

 

C

 

Transition Pipe

 

 

 

 

M36(B,H), M36P(B,H)

M42(B,H), M42P(B,H)

 

 

VM36(B,H), VM36P(B,H)

VM42(B,H), VM42P(B,H)

Vent Collar

A

40 3/8" (1020 mm)

44 3/8" (1121 mm)

 

B

21 3/8" (543 mm)

23 1/8" (587 mm)

 

C

41 1/4" (1048 mm)

48 1/4" (1226 mm)

 

Figure 9 - Installing Transition Pipe and Starter Collar

Figure 7 - Rough Opening for Installing in Wall

For more information, visit www.desatech.com

108795-01M

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Vent Decorative GAS Fireplace OWNER’S Operation and Installation ManualWhat to do if YOU Smell GAS Safety Information Table of ContentsBefore YOU Begin Safety InformationUnpacking IntroductionGAS Rating Natural Product SpecificationsSelecting Location PRE-INSTALLATION PreparationClearances 229mm Materials Header 152mm BSpacer 76mm 38mm Max Mantel Clearances and Wall DetailsInstalling Transition Pipe and Starter Collar PRE-INSTALLATION PreparationFraming Typical B-Vent Configuration Venting InstallationChecking for Proper Venting Venting InstallationWall Switch Installation InstallationOptional Wireless HAND-HELD Remote Control Installation GAS Line HOOK-UP InstallationLOG Placement for M36, M36P, VM36 and VM36P Models Ember and PAN Material PlacementLava rock provided around the front and sides of the burner LOG Placement for M42, M42P, VM42 and VM42P ModelsAppliance Enclosure Combustion AIR KIT Model AK4 OptionalOpening Vent Damper Installing Optional Glass Door AccessoryTo Turn OFF GAS To Appliance For Your Safety Read Before LightingOperating Fireplace Lighting InstructionsOptional HAND-HELD Remote Operation Pilot AssemblyInspecting Burners Operating FireplaceWiring Diagram Cleaning Maintenance Service HintsTechnical Service Replacement PartsObserved Problem Possible Cause Remedy TroubleshootingMain TroubleshootingGas leak. See Warning statement at Models Illustrated Parts BreakdownParts Available not Shown Parts ListLogsets for Models Illustrated Parts BreakdownOwners Registration Form Postage Required Accessories Warranty Information

VM36P, H) AND VM42(B, M42P, H) AND VM42P(B, M36P specifications

Desa H), M36P, H) and VM42P(B, M42P, H) and VM42(B are notable entities in the realm of technological solutions, particularly in the fields of engineering and manufacturing. These designations often pertain to advanced machine models or systems that incorporate various characteristics tailored for specific industrial applications.

The Desa H) series is recognized for its robust performance in industrial settings. It typically features enhanced efficiency and durability, making it suitable for rigorous operational environments. The key technologies integrated into the Desa H) models include high-performance motors and precision control systems that ensure optimal functionality. In particular, these systems are designed to minimize energy consumption while maximizing output across diverse applications.

Meanwhile, the M36P and its variants, including the M36P,H), are engineered with versatility in mind. They are equipped with modular components that allow for easy customization based on user requirements. This adaptability is a significant advantage, as it enables operators to modify the system to suit various tasks without extensive reconfiguration. Noteworthy features of the M36P series include advanced user interfaces that facilitate ease of operation and monitoring.

The VM42P(B, M42P, H) series takes innovation a step further by integrating state-of-the-art automation technologies. With features like smart sensors and AI-driven analytics, the VM42 models provide unprecedented levels of precision and reliability. These technologies enable predictive maintenance, allowing users to anticipate potential issues before they arise, thus reducing downtime and operational costs. The VM42(B) variant is particularly appreciated for its high throughput capabilities, making it ideal for mass production settings.

All models share common characteristics such as rugged construction, user-friendly interfaces, and compliance with international safety standards. Additionally, they are designed for scalability, which ensures that businesses can expand their operations with ease as demand grows. Enhanced connectivity options and IoT integration further allow for real-time data analysis and remote monitoring, fostering smarter production environments.

In summary, the Desa H), M36P, H) and VM42P(B, M42P, H) and VM42(B series represent a fusion of innovative engineering and practical application. Each model’s distinct features cater to a broad range of industrial needs, making them indispensable tools in modern manufacturing and engineering landscapes. Through their commitment to efficiency, adaptability, and intelligent technology, these systems pave the way for enhanced productivity and sustainability in various sectors.
Top Page Image Contents