Desa H) AND VM42P(B, M36P Unpacking, Introduction, Safety Information, Before YOU Begin

Page 3

SAFETY INFORMATION

Continued

9.You must keep control compartments, burners and circulating air passages clean. More frequent cleaning may be needed due to excessive lint and dust from carpeting, bedding material, etc. Turn off the gas valve and pilot light before cleaning fireplace.

10.Have venting system inspected annually by a qualified service person. If needed, have venting system cleaned or repaired. See Cleaning and Maintenance, page 18.

11.Keep the area around your fireplace clear of combustible ma- terials, gasoline and other flammable vapor and liquids. Do not run fireplace where these are used or stored. Do not place items such as clothing or decorations on or around fireplace.

12.Do not use this fireplace to cook food or burn paper or other objects.

13.Do not use any solid fuels (wood, coal, paper, cardboard, etc.) in this fireplace. Use only the gas type indicated on fireplace nameplate.

14.This appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or the Canadian Electrical Code, CSA C22.1.

15.Do not obstruct the flow of combustion and ventilation air in any way. Provide adequate clearances around air openings into the combustion chamber along with adequate accessibility clearance for servicing and proper operation.

16.Do not install fireplace directly on carpeting, vinyl tile or any combustible material other than wood. The fireplace must set on a metal or wood panel extending the full width and depth of the fireplace.

17.Do not use fireplace if any part has been exposed to or under water. Immediately call a qualified service person to arrange for replacement of the unit.

18.Do not operate fireplace if any log is broken.

19.Do not use a blower insert, heat exchanger insert or other ac- cessory not approved for use with this fireplace.

20.Provide adequate clearances around air openings.

UNPACKING

The following items are packed inside the firebox. Remove before positioning firebox into framing.

•Transition Collar - For vent connection

•Ceramic Log Pack - Shrink-wrapped on cardboard

•Three (3) plastic bags containing lava rock, pan and ember ma- terials

•Rear Log - Remove the two plastic quick ties from around the burner and grate

•Grate Stand - Lift off of burner pan

Check all items for any shipping damage. If damaged, promptly inform dealer or distributor where you bought the product.

Safely retain these items for later installation.

3

INTRODUCTION

Models M36(P)(B,H), VM36(P)(B,H), M42(P)(B,H) and VM42(P)(B,H) are vented gas fireplaces that use a millivolt gas control valve with a millivolt ignition system. A 6" B-Type venting system and a listed type vent cap are not supplied but are required for proper operation. See venting instructions on pages 9 and 10.

WARNING: This gas appliance must not be con- nected to a chimney flue servicing a solid fuel burning appliance.

Models M36(B,H), VM36(B,H), M42(B,H) and VM42(B,H) are factory equipped for use with natural gas and must be converted when intended for use with propane/LP gas. A respective model PCBM-36 or PCBM-42 conversion kit may be purchased for simple conversion to propane/LP gas. See Accessories, page 27.

BEFORE YOU BEGIN

Before beginning the installation of your appliance, read these instructions through completely.

This DESA appliance and its approved components are safe when installed according to this installation manual and are operated as recommended by DESA. Unless you use DESA approved com- ponents tested for this appliance, YOU MAY CAUSE A FIRE

HAZARD!

The DESA warranty will be voided by and DESA disclaims any responsibility for the following actions :

A)Modification of the appliance or any of the components.

B)Use of any component part not approved by DESA in combina- tion with this appliance.

C)Installation and/or operation in a manner other than instructed in this manual.

D)The burning of anything other than the type of gas approved for use in this gas appliance.

The installation must conform with local codes or, in the absence of local codes, with the current National Fuel Gas Code, ANSI Z223.1/NFPA 54 or with the current CAN/CGA B149 Installation Codes.

This appliance complies with ANSI Z21.50-2000and CSA 2.22-2000 as Vented Gas Fireplaces and is listed and tested by the Canadian Standards Association to the above test standards.

WARNING: Installation of this appliance should be done by a qualified service person well trained in the installation of such appliances. You will also need a building permit from your local Building and Safety Com- missioner before installing this appliance; otherwise your insurance co. may not cover this appliance.

NOTICE: This appliance is not intended to be used as a primary source of heat.

For more information, visit www.desatech.com

108795-01M

Page 2 Page 4
Image 3
Page 2 Page 4
Contents OWNER’S Operation and Installation Manual Vent Decorative GAS FireplaceWhat to do if YOU Smell GAS Safety Information Table of ContentsBefore YOU Begin Safety InformationUnpacking IntroductionGAS Rating Natural Product SpecificationsPRE-INSTALLATION Preparation Selecting LocationClearances 229mm Materials Header 152mm BSpacer 76mm 38mm Max Mantel Clearances and Wall DetailsPRE-INSTALLATION Preparation Installing Transition Pipe and Starter CollarFraming Typical B-Vent Configuration Venting InstallationChecking for Proper Venting Venting InstallationInstallation Wall Switch InstallationOptional Wireless HAND-HELD Remote Control Installation GAS Line HOOK-UP InstallationLOG Placement for M36, M36P, VM36 and VM36P Models Ember and PAN Material PlacementLava rock provided around the front and sides of the burner LOG Placement for M42, M42P, VM42 and VM42P ModelsAppliance Enclosure Combustion AIR KIT Model AK4 OptionalOpening Vent Damper Installing Optional Glass Door AccessoryTo Turn OFF GAS To Appliance For Your Safety Read Before LightingOperating Fireplace Lighting InstructionsOptional HAND-HELD Remote Operation Pilot AssemblyInspecting Burners Operating FireplaceWiring Diagram Cleaning Maintenance Service HintsTechnical Service Replacement PartsObserved Problem Possible Cause Remedy TroubleshootingMain TroubleshootingGas leak. See Warning statement at Models Illustrated Parts BreakdownParts Available not Shown Parts ListLogsets for Models Illustrated Parts BreakdownOwners Registration Form Postage Required Accessories Warranty Information

VM36P, H) AND VM42(B, M42P, H) AND VM42P(B, M36P specifications

Desa H), M36P, H) and VM42P(B, M42P, H) and VM42(B are notable entities in the realm of technological solutions, particularly in the fields of engineering and manufacturing. These designations often pertain to advanced machine models or systems that incorporate various characteristics tailored for specific industrial applications.

The Desa H) series is recognized for its robust performance in industrial settings. It typically features enhanced efficiency and durability, making it suitable for rigorous operational environments. The key technologies integrated into the Desa H) models include high-performance motors and precision control systems that ensure optimal functionality. In particular, these systems are designed to minimize energy consumption while maximizing output across diverse applications.

Meanwhile, the M36P and its variants, including the M36P,H), are engineered with versatility in mind. They are equipped with modular components that allow for easy customization based on user requirements. This adaptability is a significant advantage, as it enables operators to modify the system to suit various tasks without extensive reconfiguration. Noteworthy features of the M36P series include advanced user interfaces that facilitate ease of operation and monitoring.

The VM42P(B, M42P, H) series takes innovation a step further by integrating state-of-the-art automation technologies. With features like smart sensors and AI-driven analytics, the VM42 models provide unprecedented levels of precision and reliability. These technologies enable predictive maintenance, allowing users to anticipate potential issues before they arise, thus reducing downtime and operational costs. The VM42(B) variant is particularly appreciated for its high throughput capabilities, making it ideal for mass production settings.

All models share common characteristics such as rugged construction, user-friendly interfaces, and compliance with international safety standards. Additionally, they are designed for scalability, which ensures that businesses can expand their operations with ease as demand grows. Enhanced connectivity options and IoT integration further allow for real-time data analysis and remote monitoring, fostering smarter production environments.

In summary, the Desa H), M36P, H) and VM42P(B, M42P, H) and VM42(B series represent a fusion of innovative engineering and practical application. Each model’s distinct features cater to a broad range of industrial needs, making them indispensable tools in modern manufacturing and engineering landscapes. Through their commitment to efficiency, adaptability, and intelligent technology, these systems pave the way for enhanced productivity and sustainability in various sectors.
Top Page Image Contents